lionelo Babyline 6.2 Baby Video Monitor User Manual

June 9, 2024
lionelo

lionelo Babyline 6.2 Baby Video Monitor

lionelo Babyline 6.2 Baby Video Monitor-product

Important information

  1. Before using the product, read the instruction manual and keep it for future reference.
  2. This product is not a toy. Do not let children play with it.
  3. The product is only suitable for use in dry areas. Do not use it outdoors or on a wet surface.
  4. Do not touch the product with wet hands.
  5. If the product does not work as it should or has been dropped or flooded, contact the manufacturer’s service department.
  6. Do not disassemble the product yourself.
  7. Use only the power adapter included in the set.
  8. Do not place the product near a stove or other heat sources.
  9. Installation must be performed only by an adult. Keep smaller pieces of the set away from the child.
  10. Electronic nannies are not a substitute for proper parental care and attention.
  11. Do not place the product and its wires in the playpen or within  reach of the child. Place them at a distance of at least 1 m.
  12. Do not place the product near water or a fire source.
  13. Do not touch the contacts of the plug with sharp or metal objects.
  14. Do not use the device if the cable or plug is damaged.
  15. To unplug the device grab the plug, not the cord.
  16. If the device will not be used for an extended period of time, unplug it from the power supply.

The product complies with the requirements of European Union directives. In accordance with Directive 2012/19/EU, this product is subject to separate collection. The product should not be disposed of with municipal waste as it may pose a risk to the environment and human health. Return the used product to the recycling centre for electrical and electronic equipment.

The set (fig. A)

  1. LCD monitor
  2. Camera
  3. Power supply x 2
  4. USB-C cable
  5. Micro-USB cable
  6. Screwslionelo Babyline 6.2 Baby Video Monitor-fig-1

List of camera parts (fig. B)

  1. Lens
  2. Light sensor
  3. MicroSD card port (max. 64 GB)
  4. Temperature sensor
  5. Reset button
  6. Speaker
  7. MicroUSB portlionelo Babyline 6.2 Baby Video Monitor-fig-2

List of monitor parts (fig. C)

  1. Diode
    The diode glows green when the device is running and red when it is charging. When fully charged, the diode turns green again.

  2. Menu button
    In monitoring mode, press this button to enter the main menu. In the main menu, press the button to go to the previous page.

  3. Camera switch button
    Press this button to switch the camera. The status bar shows which camera is currently working.

  4. Direction buttons
    In the menu, buttons are used to move around the screen.

  5. USB-C port

  6. OK button
    In the main menu, press this button to confirm the selected option or action.

  7. Brightness and volume settings button

  8. Two-way audio communication button

  9. Microphone

  10. VOX mode button

  11. Monitor on/off switch
    Press and hold to turn the monitor on or off. Press briefly to activate standby mode.

  12. External antenna
    Place the antenna up for the best signal.

  13. Bracket

  14. Speaker

  15. MicroSD card port (max. 64 GB)lionelo Babyline 6.2 Baby Video Monitor-fig-3

Monitor icons (fig. D)

  1. Low battery level
  2. No signal
  3. VOX mode / Audible alarm enabled
  4. Temperature alarm
  5. Feeding time alarmlionelo Babyline 6.2 Baby Video Monitor-fig-4

Instructions for use Power supply

  1. It is recommended to fully charge the monitor before use.
  2. Connect the plug of the power cord to the monitor and the other end to the power supply. Connect the power supply to the power outlet (fig. 1).
    NOTE: Use only the power supply included in the set.lionelo Babyline 6.2
Baby Video Monitor-fig-5

Device operation

NOTE! The monitor and camera are paired by default. No re-pairing is necessary.

  1. Connect the plug of the power cord to the camera and the other end to the power supply. Connect the power supply to the power outlet (fig. 2). The device will beep.
  2. Press and hold the switch (11, fig. C) for 3-5 seconds to turn the monitor on. After about 10 seconds, the camera image will be displayed on the monitor.
  3. Place the camera in a convenient location and point it in the direction you want to monitor.
    NOTE
    Do not place the camera or wires in the baby’s crib or within reach of the baby (min. 1 meter distance) due to the risk of injuring or suffocating the baby. In the event of image or sound interference, place the devices in a different location and make sure they are not near other electrical devices.lionelo Babyline 6.2 Baby Video Monitor-fig-6

Adding a camera

It is possible to pair a total of 4 cameras.

  1. Press the back button (2, fig. C) to enter the main menu.
  2. Select the “Cameras” option, then select the channel to which the new camera is to be added (fig. 3a) and press the OK button. The camera was paired with the monitor (fig. 3b).
  3. If you have problems adding a camera, make sure the camera is connected to a power source. If so, reset the camera by pressing the reset button (5, fig. B), then add the camera manually (see: Adding a Camera) and make sure the camera and monitor are within 2 meters of each other.lionelo Babyline 6.2 Baby Video Monitor-fig-7lionelo Babyline 6.2 Baby Video Monitor-fig-8

Feeding time alarm settings

  1. In the main menu, select the “Feeding” option (fig. 4).
  2. Select the time after which the alarm should be triggered (A, fig. 4). Select whether the alarm is to be triggered once or in a loop (B, fig. 4).
  3. To turn off the feeding time alarm function, select OFF.lionelo Babyline 6.2 Baby Video Monitor-fig-9

Sound detection

Select “Sound alarm” in the main menu, then choose the sound detection sensitivity level: low, medium or high, or turn off the sound alarm completely by selecting OFF (fig. 5).

  • Low level: the device detects the baby’s crying.
  • Medium level: the device detects a loud voice.
  • High level: the device detects normal speech.
    If the receiver detects sound above the set volume level, the screen will display the icon ( ) and beep for about 30 seconds. Press any button to turn off the sound alarm.lionelo Babyline 6.2 Baby Video Monitor-
fig-10

Sound detection in energy-saving VOX mode

Before enabling VOX mode, sound detection must be enabled (see: Sound detection). To enable VOX mode, press the VOX button (10, fig. C), an icon will appear in the upper left corner ( ). The screen in sleep mode will wake up automatically when sound is detected. To turn off VOX mode, press the button again.

Temperature alarm settings

  1. In the main menu, select “Temperature alarm” (A, fig. 6).
  2. Select the unit in which the room temperature is to be displayed
  3. degrees Celsius or Fahrenheit (B, fig. 6).
  4. If the temperature exceeds or falls below a value in the default range of 18 – 30°C (64 – 86°F), an alarm lasting about 30 seconds will be triggered and an icon will appear on the screen ( ).
  5. To turn off the temperature alarm, select OFF (B, fig. 6).lionelo Babyline 6.2 Baby Video Monitor-fig-11

Melodies

  1. In the main menu, select “Music” (fig. 7). Select one of the eight available lullabies (A, fig. 7) or nature sounds (B, fig. 7) and press the OK button.
  2. It is possible to play a selected melody in continuous mode (C, fig. 7) or all melodies in a loop (D, fig. 7). The selected melody will play on both the camera and the monitor.lionelo Babyline 6.2 Baby Video Monitor-fig-12

Display settings

  1. In the main menu, select the “Display” option.
  2. Select the time after which the display should go into sleep mode (fig. 8): 1 minute, 10 minutes, 30 minutes, or continuously on (fig. 8).lionelo Babyline 6.2 Baby Video Monitor-fig-13

Brightness and volume settings

Press the button (7, fig. C), then adjust the brightness of the screen with the upper and lower direction buttons, and the volume with the right and left buttons.

Two-way audio communication

Press and hold the two-way communication button (8, fig. C) to start audio transmission, release to abort.

Video recording

  1. Insert the microSD card into the port on the monitor (15, fig. C) or the port on the camera (3, fig. B).
  2. In the main menu, select the “Recording” option (fig. 9). Make sure the date and time are up to date before recording.lionelo Babyline 6.2 Baby Video Monitor-fig-14

The camera with a microSD card can record 19201080 resolution video, which is not playable directly on the monitor. The monitor with a microSD card can record video at 800480 resolution, which can be played directly on the monitor.

Video playback

Select “Playback” from the main menu, then find the video you want to play by selecting the date or channel (fig. 10a).lionelo Babyline 6.2 Baby Video
Monitor-fig-15 Options available during playback (fig. 10b):

  • Search
  • Rewind
  • Playback/pause
  • Scroll forward
  • Fullscreenlionelo Babyline 6.2 Baby Video Monitor-fig-16

Settings

  1. In the main menu, select “System” (fig. 11). Available options include date and time settings, reset, advanced settings and system information.lionelo Babyline 6.2 Baby Video Monitor-fig-17
  2. Select the current date and time and the time format (fig. 12).lionelo Babyline 6.2 Baby Video Monitor-fig-18
  3. To return to the factory settings, select “Factory settings” and then OK (fig. 13).lionelo Babyline 6.2 Baby Video Monitor-fig-19
  4. To enter advanced settings, select “Advanced settings” (fig. 14). You can check the total and remaining capacity of the card, as well as enable or disable image rotation.lionelo Babyline 6.2 Baby Video Monitor-fig-20
  5. To view device information, select “Version” (fig. 15)lionelo Babyline 6.2 Baby Video Monitor-fig-21

Language selection

English is the device’s default language. In the main menu, select the “Language” option (fig. 16). Select one of the available languages. The device will restart automatically.lionelo Babyline 6.2 Baby Video Monitor-
fig-22

Mounting

Drill two holes in the surface where you want to mount the device (fig. 17), and then insert the wall plugs and screws into them (fig. 18). Attach the camera to the screws, hooking them through the holes in the bottom of the device (fig. 19).lionelo Babyline 6.2 Baby Video Monitor-
fig-23 lionelo Babyline 6.2 Baby Video Monitor-
fig-24

Troubleshooting

lionelo Babyline 6.2 Baby Video Monitor-
fig-28 lionelo Babyline 6.2 Baby Video Monitor-
fig-29

Dear Customer!

In case of any questions or comments on the purchased product, please contact us: at help@lionelo.com

Producer:

BrandLine Group Sp. z o. o.
ul. A. Kręglewskiego 1,
61-248 Poznań,
Poland

Information about the device

Transmission frequency: Wi-Fi 2.4 GHz
Operating temperature: 0 – 40°C
Operating environment humidity range: <85%

The photos are for reference only, the actual look of the products may differ from the ones shown in the pictures.

Simplified EU declaration of conformity BrandLine Group Sp. z o. o. hereby declares that the “BABYLINE 6.2” product complies with the directive: 2014/53/EU – RED Directive,2014/30/EU – EMC Directive, 2014/35/EU – LVD Directive, 2011/65/EU – RoHS Directive. Full content of EU declaration of conformity is available on the following website:

Detailed warranty conditions are available on the website:

 www.lionelo.com

Thank you for purchasing our product

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals