SCANSTRUT SC-CW-05F ROKK Edge Waterproof Wireless 10W Phone Charging Mount Instruction Manual
- June 4, 2024
- SCANSTRUT
Table of Contents
ROKK Wireless Edge 10W SC-CW-05F
Technical formation.
Input voltage range :
Input current max:
Output power:
Standby power draw:
Waterproof rating:
Certifications:| 10.30V DC (12/24V system) 2A
10W (9.1 V, 1.1.N
< 0.2W
IPX6 front and back
C$, CE, FCC, ROHS, UKCA,
UNECE R10 E24, IC, PSE
---|---
For the latest tech info visit: www.scanstrutcom/rokli-
wireless
READ IMPORTANT SAFETY INFORMATION LEAFLETS BEFORE INSTALLING. 
-
Select an optimum mounting location.
-
Check to view angle (a), full jaw extension (b), and 90° adjustability (c).
-
Cut out the drill template, check alignment and stick it down.
-
– Drill 06mm (0.24″) hole in the centre. – Drill 3 pilot holes (see tools required table – page 1).
-
– Lightly de-burr 6mm (0.24″) hole. – Feed the wire through the hole. – Rotate to Landscape – Apply sealant to 3 x holes. – Evenly screw the mount into place.
-
Connect wires to 12/24V supply, ensuring a waterproof connection. Fuse according to the input voltage and current.
USER GUIDE:
Place the device centrally within the ROKK Wireless Edge jaws.
CARE: wash down carefully with fresh water.
Smart LED light guide:
Solid red
The product has power and is ready to charge.
Solid green
Product charging.
Flashing red
-
Foreign object detection:
Metallic object placed on top that is not Qi-compatible. or -
Thermal cutout: internal temperature is too high/ low.
Wait for the product to return to operating temperature.
Flashing green/red
The input current is too low.
This product is designed to securely mount phones under normal usage
conditions. The end user is entirely responsible for the conditions in which
their device is used. See
WARRANTY section for further details.
Scanstrut recommends installation is carried out by a qualified electrician.
No liability is accepted for damage and/or injury caused by incorrect
installation.
WARNING:
This product is to be connected to a 12V DC or 24V DC battery power source
only.
The power supply must be switched off before installation.
An appropriate fuse or circuit breaker must be used between the battery/power
source and this product. Check for the correct polarity of all wiring before
switching the power on.
This product may contain high voltages. Do not tamper with the product.
This product is NOT approved for use in hazardous/flammable atmospheres. Do
NOT install in a hazardous/flammable atmosphere e.g. engine room.
Before drilling any holes, ensure the area behind the mounting location is
clear of wires, fuel, and all other hazardous objects.
Ensure any holes cut will not significantly weaken the structure of the
mounting surface.
If the product needs to be mounted outside, it must be mounted in a location
safely above the waterline, where it is not at risk of being submerged.
IN EXTREME USAGE ENVIRONMENTS PERFORMANCE MAY VARY.
CAUTION:
The product is designed specifically for the charging of Qi-compatible
devices.
The cable must be retained and not interfere with mechanical systems.
This product contains no user-serviceable components. Do NOT attempt to repair
or alter the product in any way.
This product will charge through non-metallic phone cases up to ~3mm thick.
Phone cases may alter overall charge performance.
When used in a very high/low ambient temperature/direct or prolonged sunlight
the product may temporarily shut down, this is a safety feature of the
electronics.
The IP rating is only valid if correctly installed as per these instructions
and on a perfectly flat, nonporous, smooth surface.
When selecting a mounting location, avoid places exposed to heat-radiating
appliances and poorly ventilated areas.
EMC INSTALLATION GUIDELINES:
Scanstrut products conform to Electromagnetic Compatibility (EMC) regulations,
to ensure that electromagnetic interference between equipment is minimized.
Correct installation is required to ensure that electromagnetic interference
is kept to a minimum.
WIRING:
When extending the cable from the battery/power source to the product, ensure
there is consistently a minimum of 10V being provided to the product. A wire
gauge of 18AWG (0.82mm2) is recommended for any length of cable extension.
The schematic in step 6 is to illustrate how the product should be connected
to a 12V DC or 24V DC battery/power supply.
ENVIRONMENTAL PROTECTION:
Waste electrical products should not be disposed of with household waste.
Please recycle where facilities exist. Check with your Local Authority or
retailer for recycling advice.
IMPORTANT:
Scanstrut Ltd. accepts no responsibility for any injuries or other damages
arising from the use of its products in any circumstances.
WARRANTY:
A 2-year, non-transferrable warranty covers this Scanstrut product only and
not any devices that are mounted in it or on it. No warranty is given for
users’ devices and users expose their devices to hazards, known or unknown, at
their own risk.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>