MINKA LAVERY 5062-66A Kearney Park 2-Light Black and Soft Brass Bath Vanity Installation Guide

MINKA LAVERY 5062-66A Kearney Park 2-Light Black and Soft Brass Bath

Vanity

Product Information

Specifications:

• Item Number: 5062-66A
• Manufacture Date: New. 2023/12/7
• Maximum Wattage: 60 watts per candelabra base bulb
• Weight: Over 10 lbs

Product Usage Instructions

Installation:
WARNING: Before starting the installation process, ensure that the power is shut off at the fuse box or circuit breaker.

1. Mounting the Fixture: Shut off power at the fuse box or circuit breaker.
2. Connecting the Wires: Connect electrical wires as shown in Fig. 2, ensuring all wire connectors are secured. Ground wire should be connected to the fixture’s ground wire or mounting plate using the green screw provided.
3. Finishing the Installation: Place fixture body over mounting plate and secure with screws. Install candelabra base bulbs up to 60 watts each or CFL/LED equivalent. Carefully insert the glass panel into the frame of the fixture body and secure them by pressing the clips on the frame.

Usage :

• After completing the installation, return power to the outlet box and test the fixture. Ensure not to exceed the maximum wattage rating specified for the bulbs.
• Note: Remove all glasses before removing canopy from mounting plate for future wire connection inspection. This will allow you to hold the fixture body securely during inspection or removal.

Maintenance:
Regularly check the fixture for any loose connections or signs of wear. Clean the glass panel and fixture body as needed using a soft, damp cloth. Avoid using harsh chemicals that may damage the fixture.

FAQ (Frequently Asked Questions)

• Q: What should I do if my outlet box does not have a ground wire?
  A: In this case, connect the fixture’s ground wire directly to the mounting plate using the green screw provided.

• Q: Can I use bulbs with wattage higher than 60 watts?
  A: No, do not exceed the maximum wattage rating of 60 watts per candelabra base bulb as specified for the fixture.

• Q: How should I handle the fixture if it weighs over 10 lbs?
  A: Ensure to remove all glasses before handling the fixture, especially when removing the canopy from the mounting plate. This will provide better support while inspecting wire connections or during fixture removal.

INSTALLATION INSTRUCTIONS

Item#5062-66A (New. 2023/12/7)
READ AND SAVE THESE INSTRUCTIONS

WARNING ! SHUT POWER OFF AT FUSEOR CIRCUIT BREAKER .

MOUNTING THE FIXTURE (Fig.1)

1. Shut off power at the fuse box or circuit breaker box and remove the old fixture including the mounting hardware.

2. Carefully unpack your new fixture and lay out all the parts in a clear area. Take care not to misplace any small parts necessary for installation.

3. Position mounting plate (A) on wall and mark location of the two mounting holes. Pre-drill holes for plastic anchors (G). Insert plastic anchors (G) into wall.

4. Attach mounting plate (A) using mounting screws (B) (Size: #8-32N*L1”) to outlet box (Not included). The side of the mounting plate marked “GND” must face out. Secure mounting plate (A) by inserting wood screws (F) through holes on mounting plate into the plastic anchors (G).
   CONNECTING THE WIRES (Fig. 2)

5. Connect electrical wires as shown in Fig. 2, making sure that all wire connectors are secured. If your outlet box has a ground wire (green or bare copper), connect fixture’s ground wire to it. Otherwise, connect fixture’s ground wire directly to mounting plate using green screw provided.

6. Tuck wire connections neatly into the outlet box.
   FINISHING THE INSTALLATION (Fig.1)

7. Place fixture body (D) over mounting plate (A), and secure with screws (C).

8. Install (2) two candelabra base bulbs up to 60 watts each or CFL or LED equivalent (not included) in accordance with the fixture specification—DO NOT EXCEED THE MAXIMUM WATTAGE RATING! (NE PAS DEPASSER LA PUISSANCE NOMINALE MAXIMALE!)

9. Carefully insert glass panel (E) into frame of fixture body (D), then secure them by pressing the clips on frame.

Your installation is now complete. Return power to the outlet box and test the fixture.
The fixture is over 10 lbs. Please remove all glasses before removing canopy from mounting plate to inspect wire connections in the future. This will allow you to hold the fixture body during wire connection inspection or fixture removal.

Min 75℃ supply conductors.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>