Westinghouse PWSC12 12 Surface Cleaner for Pressure Washers Owner’s Manual

Westinghouse PWSC12 12 Surface Cleaner for Pressure Washers

Product Specifications

• Product Name : PWSC12 Surface Cleaner
• Compatible with Westinghouse Pressure Washers up to 2500 PSI
• Maximum Flow Rate : 2.3 GPM
• Operating Pressure : 1400 to 2500 PSI

Product Usage Instructions

Installing the Surface Cleaner

1. If necessary, remove the nozzle from the end of the lance.
2. Pull back the quick-connect collar and insert the inlet adapter. Push the quick-connect collar forward to lock.
3. Ensure the surface cleaner is securely locked into the lance before use.

Using the Surface Cleaner

1. Place the surface cleaner on the horizontal surface being cleaned and start the pressure washer.
2. Squeeze the trigger and move slowly to allow the unit to clean the surface.
3. If swirling or striping occurs, slow down your pace. Clean nozzles if needed.
4. Avoid hitting raised obstacles to prevent damage. Stop if a higher vibration occurs.

Nozzle Maintenance

1. Turn off the pressure washer and water supply. Release water pressure by pulling the trigger.
2. Disconnect the surface cleaner from the lance using the quick-connect collar.
3. Clean clogged nozzles using a cleaning tool or fine needle.
4. Back-flush the nozzle with a garden hose to remove debris (avoid facing the nozzle outlet towards your face).
5. Reconnect and resume cleaning after maintenance.

Replacing the High-Pressure Filter

1. If water flow issues persist, replace the high-pressure filter.
2. Turn off the pressure washer and water supply. Release water pressure by pulling the trigger.
3. Disconnect the surface cleaner from the lance.
4. Use a slotted screwdriver to remove and replace the filter as instructed.
5. Reconnect and resume cleaning after replacing the filter.

FAQ

• Q: Can I use this surface cleaner on vertical surfaces?
  • A : No, the surface cleaner is designed for flat, horizontal surfaces only to prevent injury or damage.
• Q: What should I do if I experience a pulsing sensation while using the surface cleaner?
  • A : This may indicate a clogged nozzle. Follow the Nozzle Maintenance instructions to resolve the issue.

WARNING

Do not use for commercial use. Users must read and understand the operator’s manual for their pressure washer before using this accessory to reduce the risk of injury. Before beginning any cleaning activity, spray the pressure stream in a safe direction to make sure that all accessories are connected properly in order to minimize the danger of injury or property damage. Fits most pressure washers. Before using this attachment, make sure it is compatible and is correctly installed. Risk of fluid injections. Do not point at people, pets, electrical devices, or the unit itself. Wear eye protection designated to conform with ANSI Z87.1. Before adding, replacing, or modifying accessories, turn off the pressure washer, release the water pressure in the trigger handle, and lock the trigger handle’s lock out (if one is provided with your pressure washer). Use only with cold water and only outdoors. Store the accessory indoors. Save these guidelines. Use them to train other users and refer to them frequently. Give the user of the tool these instructions as well.

PRODUCT SPECIFICATIONS

• Connection …………………………………………..1/4 in. Quick Connect Plug Inlet
• Width of Deck …………………………………………………………………………… 12 in.
• Maximum Pressure…………………………………………………………up to 2500 psi
• Minimum Pressure………………………………………………………………….1400 psi
• Maximum Water Flow…………………………………………………………….2.3 GPM
• Minimum Water Flow……………………………………………………………..1.1 GPM
• Maximum Water Temperature ……………………………………………………..140°F

APPLICATIONS

You may use this product for the purpose(s) listed below:

Cleaning decks, sidewalks, and driveways

INSTALLING THE SURFACE CLEANER

See Figure 1.

If necessary, remove the nozzle from the end of the lance.

Pull back the quick-connect collar and insert the inlet adapter. Push the quick-connect collar forward to lock.

NOTE : Be sure the surface cleaner is securely locked into the lance before use.

WARNING

Only use the surface cleaner on flat, horizontal surfaces. To reduce the risk of injection or injury, never lift the surface cleaner from the cleaning surface while operating the pressure washer.

USING THE SURFACE CLEANER

See Figure 2.

Place the surface cleaner on the horizontal surface being cleaned and start the pressure washer.
Squeeze the trigger and move slowly allowing the unit to clean the surface

NOTE : Swirling or striping in the cleaned surface indicates you may be moving too quickly. If a slower pace doesn’t stop the condition, the surface cleaner nozzles may be clogged. See Nozzle Maintenance to clean the nozzles.

WARNING

Avoid striking any raised obstacles while using the surface cleaner as damage may occur to the unit. If contact occurs and a higher vibration of the unit begins during use, release the trigger and discontinue use. Continuing use could result in serious injury or damage to the unit.

NOZZLE MAINTENANCE

See Figure 3.

The surface cleaner comes assembled. The nozzles are approved for use with pressure washers operating at 1400 to 2500 PSI with a maximum flow rate of 2.3 GPM (1.1 GPM minimum).
A pulsing sensation felt while squeezing the trigger and/or a higher vibration in the surface cleaner may be the result of a clogged or dirty nozzle.

• Turn off the pressure washer and shut off the water supply. Place unit on the ground and pull the trigger to release the water pressure in the lance.
• Pull back the quick-connect collar to disconnect the surface cleaner from the lance.
• Use a nozzle cleaning tool or a fine needle to free any foreign materials that are clogging or restricting the nozzle.
• Use a garden hose to back-flush the nozzle and force out the debris.
  • NOTE : Never point the nozzle outlet at your face.
• Reconnect the surface cleaner to the lance.
• Turn on the water supply and start the pressure washer to resume cleaning.

REPLACING THE HIGH-PRESSURE FILTER

• See Figure 4.
• If the water still doesn’t flow freely after cleaning the deck nozzles, it may be necessary to replace the high-pressure filter. Replacement filters are available by calling our Service Hotline at 855-944-3571.
• Turn off the pressure washer and shut off the water supply. Place unit on the ground and pull the trigger to release the water pressure in the lance.
• Disconnect the surface cleaner from the lance.
• Insert a slotted screwdriver into the slot of the filter as shown and turn counterclockwise to remove.
• Insert the new filter into the inlet plug.
• Turn the filter clockwise with the slotted screwdriver until it is inside the inlet adapter and no longer visible above the top of the adapter.

REPLACEMENT PARTS

• Replacement parts are available from our Service Hotline at 855-944-3571.
• Nozzle……………………………………………………………………………..02000600-0
• High-pressure Filter…………………………………………………………..03000434-0

Service Hotline:855-944-3571

777 Manor Park Drive, Columbus, OH 43228 and Westinghouse are trademarks of Westinghouse Electric Corporation. Used under license by MWE Investments, LLC.

© 2023 MWE Investments, LLC All Rights Reserved.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>