Westinghouse 6125200 Indoor Lighting Fixture Owner’s Manual
- October 30, 2023
- Westinghouse
Table of Contents
Owner’s Manual
Indoor Lighting Fixture
Installation Instructions
FIXTURE WARRANTY
This Westinghouse lighting fixture is warranted against defects in material
and workmanship for a period of five years from purchase date. This warranty
is in lieu of all other warranties expressed or implied.
This warranty does not cover acts of nature such as lightening damage, or
corrosion and discoloration of components, nor does it cover damages caused
through abuse, improver installation, surges in electric current, or acts of
third parties.
This warranty does not cover the costs of removing and re-installing the
lighting fixture.
If this product fails for any reason covered by this warranty, please contact
us at www.westinghouselighting.com/contact-
us.
ASSEMBLY INSTRUCTIONS FOR INDOOR LIGHTING FIXTURE
Congratulations on your Westinghouse purchase. This fixture has been designed
to give you many years of beauty and service. For questions and comments,
please visit www.westinghouselighting.com/contact-
us.
NOTE: Carefully unpack fixture and parts. Make sure all parts are
included before discarding any packing materials (see figure1).
WARNING: ELECTRICAL SHOCK CAN RESULT IN SERIOUS INJURY.
Read and follow instructions exactly as shown. If instructions are unclear, do
not proceed. Contact a qualified electrician. Read all instructions before
beginning. Proper wiring is essential for safe operation of this fixture. When
cutting or drilling into walls or ceilings, do not damage electrical wiring,
gas lines, or water lines. If any of the fixture or wiring components are
damaged, do not install fixture. Return to place of purchase.
For fixtures provided with 75° C or 90° C supply wire warning only. (These
warnings are provided on the U.L. label and on the fixture carton.) Risk of
fire. Most dwellings built before 1985 have supply wires rated 60° C. Consult
a qualified electrician before installing.
FIGURE 1.
Line art shown may not exactly match the fixture enclosed.
However, the installation instructions do apply to this fixture.
*NOT SUPPLIED
MOUNTING AND WIRING INSTRUCTIONS
NOTE: Underwriters Laboratories (UL) does not require all fixtures to have ground wires. These fixtures meet all UL specifications.
- Turn off power at fuse box to avoid possible electric shock.
- Thread mounting screw (A) into the matching hole of mounting bar (B).
- Secure the mounting bar (B) to outlet box (C) with outlet box screws (D) (if applicable).
- Identify color coding of fixture wires (see figure 2).
- Connect the black wire from the fixture with the black wire (live wire) from the outlet box (C) by wire connector (E), and wrap the wire connector (E) with electrical tape for a more secure connection.
- Connect the white wire from the fixture with the white wire (neutral wire) from the outlet box (C) by wire connector (E), and wrap the wire connector (E) with electrical tape for a more secure connection.
- Partially thread green grounding screw (J) into side hole (K) on cross bar (B) (see figure 1).
- Wrap grounding wire from fixture around green grounding screw (J) leaving enough excess wire, then connect the excess grounding wire from the fixture with the grounding wire from outlet box (C) by wire connector (E) (if applicable), then wrap the wire connector (E) with electrical tape for a more secure connection.
- Tighten grounding screw (J). Do not over tighten.
- Tuck wires inside outlet box (C) (see figure 1).
ADJUSTING LENGTH OF CORD
(if needed)
These steps should only be performed by someone familiar with working with
electrical wiring. Care must be taken when adjusting the length of the cord to
ensure insulation on internal wires is not damaged. If you are not familiar
with these steps, seek the aid of a qualified electrician.
- Loosen the screw in strain relief (Q) until cord slides easily, being careful not to completely remove screw. Slide canopy down cord until the fixture is the desired distance below the canopy. Tighten the screw in the strain relief (Q) until cord does not slide.
- Cut excess cord approximately six to seven inches (6”-7”) above canopy.
- Leaving at least one inch (1”) of outer insulation above the canopy, carefully cut through outer insulation of cord, being careful not to damage inner insulation. Remove outer insulation. Strip inner insulation from end of both wires, leaving approximately 1/2 inch of wire exposed.
- For cords without differently colored inner insulation, identify the tracer lines on the new ends of the inner wires to match the labels on the original ends and connect to house wiring as described in the appropriate step listed below in the Mounting and Wiring Instructions section.
FIXTURE ASSEMBLY INSTRUCTIONS
Warning: This fixture is for indoor use only.
- Thread the decorative tube (F) onto the stud (G).
- After wires are connected, tuck them carefully inside outlet box (C). Raise canopy (H) allowing the mounting screw (A) to protrude through the hole in the canopy (H), and secure with cap nuts (L).
- Install lamp(s). Do not exceed recommended wattage.
WARNING
Turn off electricity to the mounting site before beginning installation.
Mounting instructions must be followed exactly as shown for the fixture to be
safely supported.
CLEANING AND CARE
To clean, wipe fixture with soft cloth. Clean glass with mild soap. Spray from chemical cleaners can discolor the finish of fixture. Do not use scouring pads, powders, steel wool or abrasive paper to clean this fixture.
ORDERING PARTS
Keep this manual for future reference, and in case replacement parts are needed. Available parts can be ordered from place of purchase. Use exact wording from diagrams when ordering parts.
Westinghouse Lighting, Philadelphia, PA 19154-1029,
U.S.A.
www.westinghouselighting.com
and Westinghouse are trademarks of Westinghouse Electric Corporation.
Used under license by Westinghouse Lighting.
All Rights Reserved.
Made in China
References
- LED & Conventional lighting solutions | Philips lighting
- Ceiling Fans | Lighting Fixtures | Lamps
- Contact Us
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>