Westinghouse SR32SL02H-02 Solar LED Color Changing Spot Light Instruction Manual
- October 30, 2023
- Westinghouse
Table of Contents
Westinghouse SR32SL02H-02 Solar LED Color Changing Spot Light
Product Information
The Solar LED Color Changing w/Color Lock Spot Light is a product that provides a bright and colorful lighting solution for outdoor spaces. It comes with a solar panel that charges the batteries during daylight hours, and a motion sensor that activates the lights at night. The lights are factory linked, and can not be linked with more of the same type light or any other lights. The package includes 2 lights.
INSTRUCTIONS
FOR FIRST-TIME USE: THE SOLAR LIGHT NEEDS TO CHARGE 8-12 HOURS IN FULL SUNLIGHT TO FULLY CHARGE THE BATTERIES
INSTALLATION
Choose your installation method:
- To place in soft ground, please use method A.
- To install on wall, please use method B.
A: Insert into the ground with ground stake
- Slide the ground stake into the keyholes of the mounting bracket.
- If the ground is hard and packed, moisten the ground with water before inserting the stake to avoid breakage.
- Apply pressure to light not to solar panel to insert.
B: Mounted on the wall with screws
- Mark the location where you want to mount the light fixture (CC).
- Measure the width of two holes on the mounting bracket of the light to align holes for the 2 screws (BB) on the surface. The distance between the two holes is 2.76in. (70mm). Drill two holes.
- Insert the wall anchors (AA) so they are flush with the surface.
- Insert the screws (BB) and leave at least 1/4in. (6.3mm) of the screws (BB) outside of the surface for holding the light.
- Mount the light (CC) on the screws (BB) by placing the keyholes on the mounting bracket of the light over the screw heads.
Operation
Slide the power switch (FF) to ON position before charging the battery. The spot light will not charge when power switch (FF) is in the OFF position. Light fixtures use radio frequency technology to link, and light fixtures should not be greater than 65 feet (20 m) apart for linked function to work properly. When one light is triggered by motion, both lights will activate and deliver up to 1000 lumens.
- Slide the power switch (FF) to “ON” position.
- Turn selector switch (EE) to WHITE, for white color mode, then this spot light has two performance levels: Light fixture will stay on for 30 seconds when triggered by motion delivering up to 1000 Lumens and revert back to standby mode delivering up to 50 lumens until motion is detected.
- Turn selector switch (EE) to to CYCLE, for color changing mode.
- Turn selector switch (EE) to LOCK, for color select mode. You can select the color you want.
- Adjust the solar panel to be in direct sunlight for 8-12 hours to fully charge the light.
- Loosen the wing nut to adjust the light base up and down (The maximum adjustable angle is 90°), or rotate the light base (The maximum adjustable angle is less than 360°.),and adjust two light panels (The maximum adjustable angle is 90°) to desired positions for optiomal lighting coverage.
NOTE: Slide the power switch (FF) to “ON” position before charging the
battery. The spot light will not charge when power switch (FF) is in the “OFF”
position. Motion detection range is up to 20 feet (6 m), motion detection
angle is up to 120°.
Light fixtures use radio frequency technology to link, and light fixtures
should not be greater than 65 feet (20 m) apart for linked function to work
properly. When one light is triggered by motion, both lights will activate and
deliver up to 1000 lumens. The package includes 2 lights. These 2 lights are
factory linked, and can not be linked with more of the same type light or any
other lights.
NOTE: If there are performance or quality issues, both units need to be replaced with another set
Troubleshooting
If the light does not turn on, remove the battery, wipe both ends with a clean, dry cloth and reinstall the battery. Check the battery to ensure that it is making secure contact with the terminals. If this does not work, replace with a new battery.
REPLACING THE BATTERY
- Slide the power switch (FF) to “OFF” position.
- Open the light panels, remove 6 screws from the light base using a Phillips head screwdriver.
- Pull out and remove 2 screws holding the battery compartment.
- Remove 2 old batteries and replace with 2 new 3.7V, 2000 mAh lithium (18650) rechargeable batteries.
- Secure the battery compartment and the light base with the 8 screws removed earlier.
- Slide the power switch (FF) to “ON” position.
For optimal performance, place solar spot light in direct sunlight for 8-12 hours to fully charge the batteries.
FCC Warning
Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user authority to operate the equipment. Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio / TV technician for help. RF EXPOSURE: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be.
Notes: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency enerqy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
However, there is no quarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio / TV technician for help.
RF EXPOSURE: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance of 20 cm between the radiator and your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
WARNING: Do not dispose of lithium batteries in municipal waste stream or by fire as batteries may explode. Do not open, short circuit, or destroy batteries. Dispose of batteries in accordance with Local, State, and Federal regulations. Do not mix old and new batteries. Do not mix alkaline, standard (carbon-zinc), or rechargeable (nickel cadmium, nickel metal hydride or lithium ion) batteries .
For additional help and information regarding installation, contact customer
service at 1-844-551-0680, 8am-5pm, CST Monday – Friday
customerservice@idctexas.com
and Westinghouse are trademarks of Westinghouse Electric Corporation. Used
under license by Sky Rich Star Limited. All Rights Reserved.
SOLAR LED COLOR CHANGING w/COLOR LOCK
SPOTLIGHT (FACTORY LINKED)
ITEM: SR32SL02H-02
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>