Westinghouse WSF6606 Dishwasher User Manual

Westinghouse WSF6606 Dishwasher User Manual

IMPORTANT SAFETY INSTRUCTIONS

These warnings have been provided in the interest of safety. You MUST read them carefully before installing or using the appliance. Please read the user manual carefully and store in a handy place for later reference. Pass the user manual on to possible new owners of the appliance. If you need assistance, contact your Customer Care Department. The manufacturer will not accept liability, should these instructions or any other safety instructions incorporated in this book be ignored.

Safety Information
When you take delivery of your machine

• Check for any damage to your machine or to its packaging. Never start a damaged machine, makesure to contact an authorised technician.
• Unwrap the packaging materials as indicated and dispose of them in accordance with the rules. The points to pay attention during machine installation
• Choose a suitable, safe and level location to install your machine.
• Carry out the installation and connection of your machine by following the instructions.
• This machine should be installed and repaired by an authorised technician only
• Only original spare parts should be used with the machine.
• Before commencing the dishwasher installation, be sure that the machine is unplugged.
• Check whether the indoor electrical fuse system is connected according to the regulations.
• Make sure that the electrical information on the rating plate is the same as the power supply. If not, contact an electrician.
• Always use a correctly installed shockproof socket.
• Make sure not to cause damage to the mains plug and to the mains cable. Should the mains cable need to be replaced, this must be carried out by our
• Authorised Service Centre.
• Connect the mains plug to the mains socket only at the end of the installation. Make sure that there is access to the mains plug after the installation.
• Do not pull the mains cable to disconnect the appliance. Always pull the mains plug.
• If the supply cord is damaged, it must be replaced by the manufacturer, its Authorised Service Centre orsimilarly qualified persons in order to avoid a hazard.
• Pay special attention and make sure that the machine does not crush the power cord.
• Never use an extension cord or a multiple socket to make a connection. The plug should be easilyaccessible after the machine has been installed.
• After installing the machine, run it unloaded for the first time.

In daily use

• Do not use water spray and steam to clean the appliance.
• Do not stand, sit or place a load on the open door of the dishwasher, it may fall over.
• Only use detergents and rinse aids which are produced specifically for dishwashers. Otherwise Electrolux does not take any responsibility for damage that might occur to your machine.

WARNING
The water in the machine’s washing section is not drinking water, do not drink it.

• Due to danger of explosion, do not put into the machine’s washing section any chemical agents such as solvents.
• Check whether plastic items are heat-resistant before washing them in the machine.
• Do not put into your machine those items which are not suitable for dishwashing. Also, do not overload basket.
• The machine door should not be opened while the machine is in operation, to avoid the risk of hot water spraying out. A safety device ensures that the machine stops if the door is opened.

SAFETY INFORMATION AND RECOMMENDATIONS

WARNING
PERMANENT DISABILITY
Place knives and other sharp ended objects in the cutlery basket in the point down position.

• This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety

For your children’s safety

• After removing the machine’s packaging, make sure that the packaging material is out of reach of children.
• Do not allow children to play with or start the machine.
• Keep your children away from detergents and rinse aids.
• Keep children away from the machine while it is open because there may still be residues of cleaning substances inside the machine.
• Be sure that your old machine does not pose any threat to children. Remove the dishwasher door lock and power supply cord.

In case of malfunctioning

• Any malfunction in the machine should be repaired by qualified persons. Any repair work performed by anyone other than the authorised service personnel will cause your machine to be left outside the scope of warranty.
• Prior to any repair work on the machine, be sure to unplug the dishwasher from the power supply. Do not pull by the cable when unplugging. Make sure to turn off the water tap.

Recommendations

• For energy and water saving, remove coarse residues on your dishes before placing the dishes into the machine. Start your machine after having fully loaded it.
• Use the pre-wash program only whenever necessary.
• Place items such as bowls, glasses and pots into the machine face down.

WARNING
Some dishwasher detergents are strongly alkaline. They can be extremely dangerous if swallowed. Avoid contact with the skin and eyes and keep children away from the dishwasher when the door is open. Check that the detergent compartment is empty after completion of wash cycle.

DESCRIPTION OF YOUR APPLIANCE

1. Worktop
2. Upper basket with racks
3. Upper spray arm
4. Lower spray arm
5. Filters
6. Lower basket
7. Rating plate
8. Control panel
9. Detergent and rinse-aid dispenser
10. Cutlery basket
11. Active drying unit
12. Ceiling spray rose

TECHNICAL SPECIFICATIONS

Capacity 15 place settings
Height 850 mm
Height (without worktop ) 820* mm
Width 598 mm
Depth 598 mm
Net weight 54 kg
Electricity input 220-240 V, 50 Hz
Total power 1900 W
Heating power 1800 W
Pump power 100W
Drain pump power 30 W
Water supply pressure 0.03 MPa (0,3 bar) – 1 MPa (10 bar)
Water supply temperature 5 – 60°C
Current 10 A

DESCRIPTION OF YOUR APPLIANCE

1. Power button
   When pressed on, the machine is energised andthe power light illuminates.

2. Hygiene button
   By using this option, washing temperature and time during respective programs may be changed, this ensures more hygienic washing.

3. Tablet button
   Use this option when using combined detergent that contains rinse aid and extra functions.

4. Door handle
   Use door handle to open-close the door of the machine.

5. Program button
   With the program button, you can select a suitable program for your dishes.

6. Upper basket button
   By using the ‘Upper Basket Wash ‘ feature, you can wash the dishes only on upper basket, reducing the duration of your selected programs, and decreasing your power and water consumption.

7. Start/Pause button
   The Start/Pause button will start the selected program. In the Pause condition while wash indicator light is on, Start/Pause led will blink.

8. Rinse aid power indicator
   When the rinse aid light illuminates, fill the rinse aid chamber. The power light indicates power is available to the appliance.
   NOTE: If you have used an extra option on the last washing program, this feature will remain active also on the next washing program. To deselect an option on the newly selected washing program, press the selected option button again, and check that the indicator light on the option button goes off.

9. Progress indicator Lights
   Program status can be monitored via the progress indicator lights on control panel.

   • Wash
   • Dry
   • End

10. Time Indicator and delay display
    The time indicator displays the program time and time remaining for the program. In addition you can delay the start of the program by pressing the “+” and “-” buttons before the program is commenced. The delay function is indicated by the letter “H” followed by the number of hours selected.

QUICK START GUIDE

Switching on the machine

Progress indicator
You can follow the program flow using the progress indicator up lights located on the control pane

Changing a program
If you would like to change programs while a washing program is on.

Cancelling a program
If you want to cancel current program for any reason.

INSTALLING THE MACHINE

Positioning the machine

• When considering the location for the dishwasher, ensure that there is adequate space to enable loading and unloading of the dishes
• Do not put your machine in any location where the ambient temperature can fall below 5°C.
• Before positioning, take the machine out of its packaging by following the warnings located on the package.
• Position the machine close to a water tap and drain. You need to postion your machine, taking into consideration that its connections will not be alteredonce they are made.
• Do not grip the machine by its door or panel in order to move it.
• Take care to leave a certain clearance from all sides of the machine so that you can comfortably move it back and forth during cleaning.
• Make sure that the water inlet and outlet hoses do not get squeezed while positioning the machine. Also, make sure that the machine does not stand on the electrical cable. Adjust the machine’s feet so that it is level and stable. Proper positioning of the machine ensures problem-free opening and closing of its door.
• If the door of your machine does not close properly, check if the machine is stable on the floor; if not, adjust the feet and ensure it is level and stable.

Water inlet hose
Do not use the water inlet hose of your old machine, you must use the new water inlet hose supplied with your machine. Before connecting the water inlet hose to the water tap, ensure clean water is flowing from the tap before making the connection. Connect the water inlet hose directly to the water inlet tap. The pressure supplied by the tap should be at a minimum of 0.03 MPa and at a maximum of 1 MPa. If the water pressure is above 1 MPa, a pressure- relief valve should be installed

WARNING
NOTE: Aquastop inlet hose has components using 240V. Do not cut Aquastop inlet hose. Do not let it get folded, twisted, kinked or crushed.

Caution
Always use new hoses when you connect the appliance to the water mains. Old hoses must not be used. The water inlet hose must be examined at an interval of twelve months for deterioration and replaced if necessary. In order to pass the safety valve through the kitchen cabinets, an opening of at least 45mm x 90mm is needed.

Water drain hose
If you connect the water drain hose to a trap spigot under the sink, remove the plastic membrane. If you do not remove the entire membrane, remaining food can cause a blockage in the drain hose spigot. Ensure a hose clamp is used to secure the hose to the spigot.

Water drain hose
The water drain hose can be connected either directly to the water drain hole or to the sink outlet spigot. Using a hose hook (if available), the water can be drained directly into the sink by positioning the hose hook over the edge of the sink.

WARNING
Maximum drain hose length is 4m. Longer hose length will prevent correct draining, and result in poor wash performance

Electrical Connection
The plug of your machine should be connected to an earthedoutlet that supplies suitable voltage and current. If there is noearthing installation, have a competent electrician carry out an earthing installation. In case of usage without earthing installed, our company will not be responsible for any loss of usage that might occur. The indoor fuse current value should be 10-16 A. Your machine is designed for 220-240 V. The machine should not be plugged in during installation.

• Always use the molded plug supplied with your machine.
• Running in low voltage will cause a decline in washing quality.
• The machine’s electrical cable should be replaced by an authorised service or an authorised electrician only. Failure to do so may lead to accidents.
• For safety purposes, always make sure to disconnect the plug when a wash program is finished.
• In order not to cause an electric shock, do not unplug when your hands are wet.
• When disconnecting your machine from the mains supply, always pull from the plug. Never pull the cord itself.

Fitting the machine undercounter
If you wish to fit your machine undercounter, check whether you have sufficient space under your countertop and whether the wiring-plumbing is suitable to do so.

1. To ensure the stability of the dishwasher for an underbench installation, if the underbench dimension is greater than 820mm, any gap between the dishwasher and the underside of the benchtop should be bridged with a packing piece. This may be achieved by wedging a piece of timber between the dishwasher and the benchtop as shown
2. If required, remove the worktop as shown in the illustration.
3. To remove the worktop, remove the screws that hold the worktop which are located at the rear of the machine; then push the front panel 1 cm from the front towards the rear and lift it.
4. Adjust the machine feet according to the slope of the floor.
5. Fit your machine by pushing it undercounter without letting the hoses get crushed or bent .

WARNING
After removal of worktop, ensure the opening for the dishwasher is according to the following dimensions.

PREPARING THE MACHINE FOR USE

Detergent usage
Use a detergent specifically designed for use in domestic dishwashers . You can find powder, gel, and tablet detergents in the market that have been designed for household dishwashers . Detergent should be put into the compartment prior to starting the machine . Keep your detergents in cool, dry places out of reach of your children . Do not fill detergent into the detergent compartment more than required; otherwise it may etch your glasses as well as leaving undissolved detergent in the dishwasher. Should you need more information concerning the detergent to use, contact detergent manufacturers directly

PROGRAM DESCRIPTIONS

NAME OF PROGRAM| RINSE**| FAST 30| **ECO*| TIME SAVE| HEAVY| INTENSIVE
---|---|---|---|---|---|---
WASHING TEMPERATURE| –| 40°C| 50°C| 65°C| 60°C| 65°C
TYPE OF FOOD SOILS| Pre wash to rinse and loosen food residue| Fresh coffee, milk, tea, cold meat, vegetables| Fresh coffee, milk, tea, cold meat, vegetables| Baked on soup, sauce, pastry, egg, rice, potato and meats cooked in oven, fried food| Fresh coffee, milk, tea, cold meat, vegetables| Dishes with dense dried on soils or for hygienic washing
LEVEL OF FOOD SOILS| Small| Small| Medium| Medium| Medium| High
AMOUNT OF DETERGENT A: 25GM/ 15GM B: 5GM| | A: 15| A: 25B: 5| A: 25B: 5| A: 25B: 5| A: 40B: 5
| Pre-wash| 40°C Wash| Pre-wash| 65°C Wash| Pre-wash| Pre-wash
Finish| Cold Rinse| 50°C Wash| Intermedi- ate Rinse| 60°C Wash| 55°C Wash
| Hot Rinse| Cold Rinse| Hot Rinse| Cold Rinse| 65°C Wash
End| Hot Rinse| End| Hot Rinse| Cold Rinse
| Dry| | Dry| Intermedi- ate Rinse
End| End| Hot Rinse
| Dry
PROGRAM TIME (MINS)| 15| 30| 122| 50| 94| 167
POWER CONSUMPTION (KW HOUR)| 0.02| 0.84| 0.95| 1.21| 1.34| 1.73
WATER CONSUMPTION (LITRES)| 4.2| 10.9| 13.5| 10.7| 14.4| 24.6
SELECTABLE OPTIONS**| | | Upper basket| Upper basket| Upper basket| Upper basket
| Tablet| Tablet| Tablet| Tablet| Tablet
| | Hygiene| Hygiene| Hygiene| Hygiene

MAINTENANCE AND CLEANING

Cleaning the seals in the machine door
To clean any accumulated residues in the door seals, wipe the seals regularly by using a dampened cloth.

Cleaning the machine
Clean the filters and spray arms at least once a week. Unplug your machine and turn off its tap before starting the cleaning. Do not use abrasive materials when cleaning your machine. Wipe with a fine cleaning material and a dampened cloth.

Filters
Check if any food wastes have remained on the coarse and fine filters. If any food waste is found, remove the filters and clean them thoroughly with water under the tap.
a. Micro Filter
b. Coarse Filter
c. Metal

1. To remove and clean the filter combination (a+b), turn it counter clockwise and remove it by lifting upwards.
2. Pull and remove the metal filter (c).
3. Then pull the coarse filter out of the micro filter. Rinse it with water under the tap and reassemble.
4. Relocate the Coarse/Micro filter combination into the metal filter and turn it in the direction of the arrow It is locked when the arrows on the micro filter can be seen on either side.
5. Reposition the metal filter in the machine.
6. Never use your dishwasher without any filter.
7. Incorrect fitting of the filter will reduce the washing effectiveness.
8. Clean filters are very important in terms of the proper running of the machine.

FAILURE CODES AND WHAT TO DO IN CASE OF FAILURE

F1| Leak detection| •    Switch off the dishwasher and close the tap.• Contact the service centre.
---|---|---
F2| Draining fault| •    Cancel program and power off machine, then check the following.•    Spigot on sink trap is clogged.•    Check if the drain spigot membrane has been removed.•    Drain hose is clogged.•    Filters of the dishwasher may be clogged.•    If error continues contact the service centre.
F3| Water overfill| •    Close the tap.•    Contact the service centre.
F5| Water supply fault| •    Make sur e the water tap is open and the main water supply is on.•    Close he tap, disconnect the hose and clean the filter at the tap connection end.•    Check the inlet hose is not kinked.• If error continues contact the service centre.
F6| Faulty heater sensor| •    Contact the service centre.
F7| Overheating (water temperature too high)| •    Contact the service centre.
F8| Not heating| •    Contact the service centre.
F9| Flow control position error| •    Contact the service centre.
FE| Power supply fault| •    Restart the dishwasher.
H01 – H24| Delay has been selected| •    Cancel the delay setting.

TROUBLESHOOTING

•    Your machine’s door is open, shut the door.
If the program won’t start| •    Check if the plug is connected.•    Check your indoor fuses.•    Be sure that the water inlet tap is turned on.•    Be sure that you have closed the machine door.•    Be sure that you switched off the machine by pressing the Power On/Off button.•    Be sure that the water inlet filter and the machine filters are not clogged.• First time use: Check if the drain spigot’s membrane has been removed or spigot blocked.•    Check if the delay start has been selected – reset.
If detergent residues are left in the detergent compartment| • Detergent has been added when the detergent compartment was wet.•    A large dish in the lower basket has blocked the dispenser door.
If water is left inside the machine at the end of the program| •    The water drain hose is clogged or twisted.•    The filters are clogged.•    The program is not finished yet.
If the machine stops during a wash operation| •    Power failure.• Water inlet failure.•    Program can be on standby mode.
If shaking and hitting noises are heard during a wash operation| • Dishes placed incorrectly.•    Spray arm hitting the dishes.
If there are partial food wastes left on the dishes| •    Dishes placed incorrectly into the machine, sprayed water did not reach related places.• Basket over loaded.•    Dishes leaning against one another.•    Very small amount of detergent added.•    An unsuitable, rather weak wash program selected.•    Spray arm clogged with food wastes.•    Filters clogged.• Filters incorrectly fitted.•    Water drain pump clogged.
If there are whitish stains on the dishes| • A very small amount of detergent is being used.•    Rinse aid dosage setting at a very low level.
If the dishes won’t dry up| •    A program without a dry operation selected.•    Rinse aid dosage set too low.•    Dishes unloaded too fast.
If there are rust stains on the dishes| • Stainless-steel quality of the dishes washed is insufficient.•    Unhealthy mains grounding.

References

• Welcome to Electrolux
• Home & Kitchen Appliances | Electrolux Australia

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>