Westinghouse W-766 Indoor Lighting Fixture Owner’s Manual
- October 30, 2023
- Westinghouse
Table of Contents
Westinghouse W-766 Indoor Lighting Fixture
FIXTURE WARRANTY
This Westinghouse lighting fixture is warranted against defects in material
and workmanship for a period of five years from purchase date. This warranty
is in lieu of all other warranties expressed or implied.
This warranty does not cover acts of nature such as lightening damage, or
corrosion and discoloration of components, nor does it cover damages caused
through abuse, improver installation, surges in electric current, or acts of
third parties.
This warranty does not cover the costs of removing and re-installing the
lighting fixture.
If this product fails for any reason covered by this warranty, please contact
us at www.westinghouse-lighting.com/contact-us
ASSEMBLY INSTRUCTIONS FOR INDOOR LIGHTING FIXTURE
Congratulations on your Westinghouse purchase. This fixture has been designed
to give you many years of beauty and service. For questions and comments,
please visit www.westinghouselighting. com/contact-us.
NOTE: Carefully unpack fixture and parts. Make sure all parts are included
before discarding any pack-ing materials (see figure 1).
WARNING: ELECTRICAL SHOCK CAN RESULT IN SERIOUS INJURY.
Read and follow instructions exactly as shown. If instructions are unclear, do
not proceed. Contact a qualified electrician. Read all instructions before
beginning. Proper wiring is essen-tial for safe operation of this fixture.
When cutting or drilling into walls or ceilings, do not dam-age electrical
wiring, gas lines, or water lines. If any of the fixture or wiring components
are damaged, do not install fixture. Return to place of purchase.
For fixtures provided with 75° C or 90° C supply wire warning only. (These
warnings are provid-ed on the U.L. label and on the fixture carton.) Risk of
fire. Most dwellings built before 1985 have supply wires rated 60° C. Consult
a qualified electrician before installing.
MOUNTING AND WIRING INSTRUCTIONS
NOTE: Underwriters Laboratories (UL) does not require all fixtures to have ground wires. These fixtures meet all UL specifications.
- Turn off power at circuit box to avoid possible electric shock.
- Remove cap nuts (A) and universal mounting plate or cross bar (C) from back plate (B) (if needed), leave mounting screws (D) in place. (see fig. 1)
- Secure universal mounting plate or cross bar (C) to outlet box (E) with outlet box screws (F) (if applicable).
- Identify color coding of fixture wires (see fig. 2).
- Connect the black wire from the fixture with the black wire (live wire) from the outlet box by wire connector (G), and wrap the wire connector (G) with electrical tape for a more secure connection.
- Connect the white wire from the fixture with the white wire (neutral wire) from the outlet box by wire connector (G), and wrap the wire connector (G) with electrical tape for a more secure connection.
- Partially thread green grounding screw (H) into side hole (I) on universal mounting plate or cross bar (C) (see fig.1).
- Wrap grounding wire from fixture around green grounding screw stem (H) leaving enough excess wire, then connect the excess grounding wire from the fixture with the grounding wire from outlet box by wire connector (G) (if applicable), then wrap the wire connector (G) with electrical tape for a more secure connection.
- Tighten green grounding screw (H). Do not over tighten.
- Tuck wires inside outlet box (E) (see fig. 1).
F IXTURE ASSEMBLY INSTRUCTIONS
Warning: This fixture is for indoor use only.
-
Position back plate (B) over mounting screws (D) by aligning back plate openings (J) with mounting screws (D).
-
Secure with cap nuts (A).
-
Remove retaining ring (O). Install glass shade (L) and plate (S) (if applicable) into holder(s) (M).
Secure with plate (S) (if applicable) and retaining ring(s) (O). -
Secure tail final (P) to bottom of fixture arm (Q).
-
Install lamp(s). Do not exceed recommended wattage.
-
Turn power back on at circuit box.
WARNING
Turn off electricity to the mounting site before beginning installation.
Mounting instructions must be followed exactly as shown for the fixture to be
safely supported.
CLEANING AND CARE
To clean, wipe fixture with soft cloth. Clean glass with mild soap. Spray from
chemical cleaners can discolor the finish of fixture. Do not use scouring
pads, powders, steel wool or abrasive paper to clean this fixture.
ORDERING PARTS
Keep this manual for future reference, and in case replacement parts are
needed. Available parts can be ordered from place of purchase. Use exact
wording from diagrams when ordering parts.
Westinghouse Lighting, Philadelphia, PA 19154-1029, U.S.A. and Westinghouse
are trademarks of Westinghouse Electric Corporation.
Used under license by Westinghouse Lighting.
References
- LED & Conventional lighting solutions | Philips lighting
- Ceiling Fans | Lighting Fixtures | Lamps
- Contact Us
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>