Westinghouse 6126200 Elway 14 in. 2 Light Barnwood Finish with Galvanized Steel Accents Flush Mount Instruction Manual

Westinghouse 6126200 Elway 14 in. 2 Light Barnwood Finish with Galvanized

Steel Accents Flush Mount

Product Information:

The Westinghouse lighting fixture is an indoor lighting fixture that comes with a warranty against defects in material and workmanship for five years from the date of purchase. The warranty does not cover damages caused by acts of nature, abuse, improper installation, surges in electric current, or acts of third parties.
The product requires careful unpacking and includes a fixture, parts, and assembly instructions.

Product Usage Instructions:

1. Carefully unpack the fixture and parts and ensure that all parts are included before discarding any packing materials.

2. Read and follow the instructions exactly as shown. If the instructions are unclear, do not proceed and contact a qualified electrician.

3. Proper wiring is essential for safe operation of this fixture.
   When cutting or drilling into walls or ceilings, do not damage electrical wiring, gas lines, or water lines.

4. If any of the fixture or wiring components are damaged, do not install the fixture and return it to the place of purchase.

5. Connect the black wire from the fixture with the black wire (hot wire) from the outlet box (C) by wire connector (F), and wrap the wire connector (F) with electrical tape for a more secure connection.

6. Connect the white wire from the fixture with the white wire (neutral wire) from the outlet box (C) by wire connector (F), and wrap the wire connector (F) with electrical tape for a more secure connection.

7. Partially thread green grounding screw (G) into side hole (H) on mounting bar (B).

8. Wrap grounding wire from fixture around green grounding screw (G) leaving enough excess wire, then connect the excess grounding wire from the fixture with the grounding wire from outlet box (C) by wire connector (F) (if applicable), then wrap the wire connector (F) with electrical tape for a more secure connection.

9. Tighten green grounding screw (G). Do not over tighten.

10. Tuck wires inside outlet box (C).

11. Attach the four support arms (J) to the canopy (E) using the fixture screws 1 (K1). Then attach the decorative frame (M) to the bottom part of the support arms (J) with fixture screws 2 (K2).

12. Raise canopy (E) to ceiling allowing mounting screws (A) to protrude through openings in canopy.

Warning: This fixture is for indoor use only.

FIXTURE WARRANTY

This Westinghouse lighting fixture is warranted against defects in material and workmanship for a period of five years from purchase date. This warranty is in lieu of all other warranties expressed or implied.
This warranty does not cover acts of nature such as lightening damage, or corrosion and discoloration of components, nor does it cover damages caused through abuse, improver installation, surges in electric current, or acts of third parties.
This warranty does not cover the costs of removing and re-installing the lighting fixture.
If this product fails for any reason covered by this warranty, please contact us at www.westinghouse-lighting.com/contact-us.

ASSEMBLY INSTRUCTIONS FOR INDOOR LIGHTING FIXTURE

Congratulations on your Westinghouse purchase. This fixture has been designed to give you many years of beauty and service. For questions and comments, please visit www.westinghouselighting. com/contact-us.
NOTE: Carefully unpack fixture and parts. Make sure all parts are included before discarding any pack-ing materials (see figure 1).
WARNING: ELECTRICAL SHOCK CAN RESULT IN SERIOUS INJURY.
Read and follow instructions exactly as shown. If instructions are unclear, do not proceed. Contact a qualified electrician. Read all instructions before beginning. Proper wiring is essen-tial for safe operation of this fixture. When cutting or drilling into walls or ceilings, do not dam-age electrical wiring, gas lines, or water lines. If any of the fixture or wiring components are damaged, do not install fixture. Return to place of purchase.
For fixtures provided with 75° C or 90° C supply wire warning only. (These warnings are provid-ed on the U.L. label and on the fixture carton.) Risk of fire. Most dwellings built before 1985 have supply wires rated 60° C. Consult a qualified electrician before installing.

MOUNTING AND WIRING INSTRUCTIONS

NOTE: Underwriters Laboratories (UL) does not require all fixtures to have ground wires. These fixtures meet all UL specifications.

1. Turn off power at circuit box to avoid possible electric shock.

2. Thread mounting screws (A) into mounting bar (B) (may be preinstalled).

3. Secure mounting bar (B) to outlet box (C) with outlet box screws (D) (if applicable).

4. Identify color coding of fixture wires.

5. Connect the black wire from the fixture with the black wire (live wire) from the outlet box (C) by wire connector (F), and wrap the wire connector (F) with electrical tape for a more secure connection.

6. Connect the white wire from the fixture with the white wire (neutral wire) from the outlet box (C) by wire connector (F), and wrap the wire connector (F) with electrical tape for a more secure connection.

7. Partially thread green grounding screw (G) into side hole (H) on mounting bar (B) .

8. Wrap grounding wire from fixture around green grounding screw (G) leaving enough excess wire, then connect the excess grounding wire from the fixture with the grounding wire from outlet box
   (C) by wire connector (F) (if applicable), then wrap the wire connector (F) with electrical tape for a more secure connection.

9. Tighten green grounding screw (G). Do not over tighten.

10. Tuck wires inside outlet box (C) .

FIXTURE ASSEMBLY INSTRUCTIONS

Warning: This fixture is for indoor use only.

1. Attach the four support arms (J) to the canopy (E) using the fixture screws 1 (K1). Then attach the decorative frame (M) to the bottom part of the support arms (J) with fixture screws 2 (K2).
2. Raise canopy (E) to ceiling allowing mounting screws (A) to protrude through openings in canopy (E) and secure into place with cap nuts (I).
3. Install lamp(s). Do not exceed recommended wattage.
4. Turn power back on at circuit box.

WARNING
Turn off electricity to the mounting site before beginning installation.
Mounting instructions must be followed exactly as shown for the fixture to be safely supported.

CLEANING AND CARE

To clean, wipe fixture with soft cloth. Clean glass with mild soap. Spray from chemical cleaners can discolor the finish of fixture. Do not use scouring pads, powders, steel wool or abrasive paper to clean this fixture.
ORDERING PARTS
Keep this manual for future reference, and in case replacement parts are needed. Available parts can be ordered from place of purchase. Use exact wording from diagrams when ordering parts.
www.westinghouselighting.com

References

• LED & Conventional lighting solutions | Philips lighting
• Ceiling Fans | Lighting Fixtures | Lamps
• Contact Us

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>