Westinghouse 6127500 Indoor Lighting Fixture Owner’s Manual

Westinghouse 6127500 Indoor Lighting Fixture

Product Information Westinghouse Indoor Lighting Fixture

The Westinghouse Indoor Lighting Fixture comes with a five-year warranty against defects in material and workmanship. The warranty does not cover damages caused by acts of nature such as lightning damage, or corrosion and discoloration of components, damages caused through abuse, improper installation, surges in electric current, or acts of third parties. The assembly instructions for the fixture are included in the user manual, and proper wiring is essential for safe operation of the fixture. The fixture is designed to provide many years of beauty and service.

Product Usage Instructions Pendant Mounting Option

1. Turn off power at circuit box to avoid possible electric shock.
2. Thread mounting screws (A) into the cross bar (B).
3. Secure cross bar (B) to outlet box (C) with outlet box screws (D) (if applicable) (see fig. 1).
4. Attach the four support arms (E) to the fixture body (J) using the fixture screws 1 (K1). Then attach the decorative frame (S) to the bottom part of the support arms (E) with fixture screws 2 (K2).
5. Remove and keep the decorative nut (R) from the cotter pin (L). Connect the bottom loop 3 (I3) from the stem (V) to the fixture body (J) with cotter pin (L). Secure cotter pin (L) by decorative nut (R).
6. Open one link on bottom end of chain (H). Attach to the bottom end of chain (H) and fixture loop 2 (I2). Securely close link on chain (H).
7. Lace wires up through every other link on chain (H) then through canopy loop 1 (I1), canopy (F).

Note : Underwriters Laboratories (UL) does not require all fixtures to have ground wires. These fixtures meet all UL specifications.

FIXTURE WARRANTY

This Westinghouse lighting fixture is warranted against defects in material and workmanship for a period of five years from purchase date. This warranty is in lieu of all other warranties expressed or implied. This warranty does not cover acts of nature such as lightening damage, or corrosion and discoloration of components, nor does it cover damages caused through abuse, improver installation, surges in electric current, or acts of third parties. This warranty does not cover the costs of removing and re-installing the lighting fixture. If this product fails for any reason covered by this warranty, please contact us at www.westinghouselighting.com/contact- us.

ASSEMBLY INSTRUCTIONS FOR INDOOR LIGHTING FIXTURE

Congratulations on your Westinghouse purchase. This fixture has been designed to give you many years of beauty and service. For questions and comments, please visit www.westinghouselighting.com/contact- us.

NOTE : Carefully unpack fixture and parts. Make sure all parts are included before discarding any packing materials (see figure 1).

WARNING: ELECTRICAL SHOCK CAN RESULT IN SERIOUS INJURY. Read and follow instructions exactly as shown. If instructions are unclear, do not proceed. Contact a qualified electrician. Read all instructions before beginning. Proper wiring is essential for safe operation of this fixture. When cutting or drilling into walls or ceilings, do not damage electrical wiring, gas lines, or water lines. If any of the fixture or wiring components are damaged, do not install fixture. Return to place of purchase. For fixtures provided with 75° C or 90° C supply wire warning only. (These warnings are provided on the U.L. label and on the fixture carton.) Risk of fire. Most dwellings built before 1985 have supply wires rated 60° C. Consult a qualified electrician before installing.

PENDANT MOUNTING AND WIRING INSTRUCTIONS

NOTE : Underwriters Laboratories (UL) does not require all fixtures to have ground wires. These fixtures meet all UL specifications

1. Turn off power at circuit box to avoid possible electric shock.
2. Thread mounting screws (A) into the cross bar (B).
3. Secure cross bar (B) to outlet box (C) with outlet box screws (D) (if applicable) (see fig. 1).
4. Attach the four support arms (E) to the fixture body (J) using the fixture screws 1 (K1). Then attach the decorative frame (S) to the bottom part of the support arms (E) with fixture screws 2 (K2).
5. Remove and keep the decorative nut (R) from the cotter pin (L). Connect the bottom loop 3 (I3) from the stem (V) to the fixture body (J) with cotter pin (L). Secure cotter pin (L) by decorative nut (R).
6. Open one link on bottom end of chain (H). Attach to the bottom end of chain (H) and fixture loop 2 (I2). Securely close link on chain (H).
7. Lace wires up through every other link on chain (H) then through canopy loop 1 (I1), canopy (F) and nipple (G).
8. Open one link on top end of chain (H). Attach to canopy loop 1 (I1) and canopy (F). Securely close link on chain (H).
9. Identify color coding of fixture wires (see fig. 3).
10. Connect the smooth wire with marking printed or molded from the fixture with the black wire from outlet box (C) by wire connector (N), and wrap the wire connector (N) with electrical tape for a more secure connection.
11. Connect the ribbed wire from the fixture with the white wire from the outlet box (C) by wire connector (N), and wrap the wire connector (N) with electrical tape for a more secure connection.
12. Partially thread green grounding screw (O) into side hole (P) on cross bar (B).
13. Wrap grounding wire from fixture around green grounding screw (O) leaving enough excess wire, then connect the excess grounding wire from the fixture with the grounding wire from outlet box (C) by wire connector (N) (if applicable), then wrap the wire connector (N) with electrical tape for a more secure connection.
14. Tighten green grounding screw (O). Do not over tighten.
15. Tuck wires inside outlet box (C).
16. Raise canopy (F) to ceiling over mounting screws (A).
17. Secure into place with cap nuts (Q).

FIXTURE ASSEMBLY INSTRUCTIONS

Warning : This fixture is for indoor use only.

1. Install lamp(s). Do not exceed recommended wattage.
2. Turn power back on at circuit box.

SEMI-FLUSH MOUNTING AND WIRING INSTRUCTIONS

NOTE : Underwriters Laboratories (UL) does not require all fixtures to have ground wires. These fixtures meet all UL specifications.

1. Turn off power at circuit box to avoid possible electric shock.
2. Thread mounting screws (A) into the cross bar (B).
3. Secure cross bar (B) to outlet box (C) with outlet box screws (D) (if applicable) (see fig. 2).
4. Attach the four support arms (E) to the fixture body (J) using the fixture screws 1 (K1). Then attach the decorative frame (S) to the bottom part of the support arms (E) with fixture screws 2 (K2).
5. Remove and keep the decorative nut (R) from the cotter pin (L). Connect the loop 1 (I1) from canopy (F) to the fixture body (J) by cotter pin (L). Secure cotter pin (L) by decorative nut (R).
6. Thread fixture wires through loop 1 (I1) and canopy (F).
7. Identify color coding of fixture wires (see fig. 3).
8. Connect the smooth wire with marking printed or molded from the fixture with the black wire from outlet box (C) by wire connector (N), and wrap the wire connector (N) with electrical tape for a more secure connection.
9. Connect the ribbed wire from the fixture with the white wire from the outlet box (C) by wire connector (N), and wrap the wire connector (N) with electrical tape for a more secure connection.
10. Partially thread green grounding screw (O) into side hole (P) on cross bar (B).
11. Wrap grounding wire from fixture around green grounding screw (O) leaving enough excess wire, then connect the excess grounding wire from the fixture with the grounding wire from outlet box (C) by wire connector (N) (if applicable), then wrap the wire connector (N) with electrical tape for a more secure connection.
12. Tighten green grounding screw (O). Do not over tighten.
13. Tuck wires inside outlet box (C).
14. Raise canopy (F) to ceiling over mounting screws (A).
15. Secure into place with cap nuts (Q).

FIXTURE ASSEMBLY INSTRUCTIONS

Warning : This fixture is for indoor use only.

1. Install lamp(s). Do not exceed recommended wattage.
2. Turn power back on at circuit box.

WARNING
Turn off electricity to the mounting site before beginning installation. Mounting instructions must be followed exactly as shown for the fixture to be safely supported.

CLEANING AND CARE

To clean, wipe fixture with soft cloth. Clean glass with mild soap. Spray from chemical cleaners can discolor the finish of fixture. Do not use scouring pads, powders, steel wool or abrasive paper to clean this fixture.

ORDERING PARTS

Keep this manual for future reference, and in case replacement parts are needed. Available parts can be ordered from place of purchase. Use exact wording from diagrams when ordering parts

Westinghouse Lighting, Philadelphia, PA 19154-1029, U.S.A. www.westinghouselighting.com and Westinghouse are trademarks of Westinghouse Electric Corporation. Used under license by Westinghouse Lighting. All Rights Reserved. Made in China

References

• LED & Conventional lighting solutions | Philips lighting
• Ceiling Fans | Lighting Fixtures | Lamps
• Contact Us

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>