ideal lux 8I135250 Bubble Outdoor Ceiling Wall 1Lt Light Instruction Manual

REV 13/10/2023
Bubble PL1

8I135250 Bubble Outdoor Ceiling Wall 1Lt Light

FOLLOW THE ASSEMBLY INSTRUCTIONS BY READING THE NUMERICAL PROGRESSION
THE LIGHTING FITTING SHOULD BE INSTALLED BY A QUALIFIED ELECTRICIAN

SAFETY INSTRUCTIONS

1. This fitting is produced and tested in accordance with the strictest European safety standards (EN 50.598-1).
2. This fitting carrot be disposed of as household waste. For disposal information ask the local authorities about ham to collect it.
3. As indicated by specific regulations. the lighting fining should be installed by a quailed electrician.
4. If the external wire is damaged it has to be replaced exclusively by the manufacturer. distributor or by a quilted electrician.
5. Alwar isolate power before commencing Istallation. maintenance or repair.
6. The Iminaire contains certain parts which can be vent hot.
7. Each material requires spec& mounting accessories. Use screws and wall pigs suitable for the material to which they are fastened. Those incised may be unsuitable.
8. Always tighten the screws fist Ni to avoid contact problems.
9. This firing should oily be installed indoors.
10. Luminaires not suitable for recessed on normally flammable surfaces.
11. Luminare not suitable for direct mounting on normal flammable surfaces.
12. This fitting is only suitable for feting to the ceding.
13. This fining is only suitable for feting to the wall.
14. The weight of the lamp has to be supported by the chain. Arhat the length ci the electric wire so that it is longer than the chart.
15. Only use lamps which do rot exceed the maximum specified wattage.
16. Always observe the minimum distance between the largo and the surface being lit as shown in the icon. The lamp can cause a fre if the tritium distance is not observed.
17. Auto protected bulb Only use bobs marked with this symbol. Halogen bulbs gat very hot. Wert until they cool down before replacing.
18. Cracked a broken safety glass has to be replaced immediately. Use only manufcturer approved parts complying with regulations.
19. Light source with not-substitutable light emitting diode ILED). Do not disassemble the product since the diodes can damage the eyes. Do not immerse in water. Wipe with a damp cloth. Do not use solvents or strong detergents.
20. This fitting is equipped with a fuse. If the lamp is out of order. replace the internal fuse.
21. Class I Electrical safety guaranteed by the man insulation and an additional protective conduc-tor (earthing) connected with the metal frame of the lamp. Eating is obligatory.
22. Class II Electrical safety guaranteed by the main insulation and a dable or reinforced insulation. Earthing not necessary.
23. Class Ill Electrical safety guaranteed by very low power supply (less than 50 Volt). Earthing excluded.
24. Not protected.
25. Protected against solid objects greater than 53 mm.
26. Protected against solid objects greater than 12 mm.
27. protected against solid objects greater than 2.5 mm.
28. protected agents solid objects greater than turn.
29. Dust protected.
30. Totaly protected agents dust infiltration
31. Not protected.
32. Protected against vertically faling water drops.
33. Protected against water drops faling with a maximin angle of 154 to the vertical axis.
34. Protected against rain.
35. Protected against splashing water.
36. Protected against water jets.
37. Protected against strong water jets.
38. Protected against temporry immersion.
39. Protected against prolonged immersion.
40. Longhaired not suitable for covering with thermally insulating material.
41. Caution. risk cf electric shock
42. Do not stare at the operating light same.

IDEAL LUX s.r.l.
Via Taglio Destro 32
30035 Mirano (VE) Italy
www.ideal-lux.com
IDEAL LUX Warehouse
Via delle Industrie, 8/D
30036 Santa Maria di Sala (Venezia)
8.00 – 12.00 / 13.30 – 17.00

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>