Somogyi KPE 6039G Kitchen Hood Instruction Manual

Somogyi KPE 6039G Kitchen Hood

Other Models

• KPE 6039G
  

• KPE 9039G
  

KITCHEN EXHAUST HOOD, CYCLONE SERIES

Carefully read the instructions for use before using the appliance.

Illustrations contained in this instructions for use are only for reference, and always the actual version of the product applies.

ADVICE AND RECOMMENDATIONS

This instructions for use applies to multiple versions of the appliance. Accordingly, it may contain the description of functions, which do not apply to your actual appliance.

WARNINGS

INSTALLATION

• The manufacturer does not assume responsibility for damage due to erroneous or incorrect installation.

• The minimum safety distance between the cooktop and the exhaust hood is 650mm (some models may be installed lower, refer to the sections on dimensions and installation).
  

• Verify, that the available mains voltage complies with the rated voltage of the exhaust hood indicated on the product label inside the appliance.

• In case of appliances with class I. contact protection, verify, whether the household power supply provides adequate earth protection.

• Connect the exhaust hood to an exhaust duct with a pipe of at least 120mm diameter. Keep the length of the exhaust duct to the minimum, as much as possible.

• Do not connect the exhaust hood to the flue of appliances, which produce combustion products, or exhaust gases (gas heaters, fireplaces, etc.).

• If the exhaust hood is used with appliances other than electric (e.g. stove with gas burner), adequate ventilation must be ensured within the room, in order to prevent the backflow of exhaust gases. The kitchen should have an opening directly connected to outdoor air, to ensure the entry of fresh air. If the kitchen exhaust hood is used with appliances powered by other sources, than electricity, the negative pressure within the room may not exceed the 0.04 mbar value, in order to prevent the reverse suction of smoke and gases indoors by the exhaust hood.

• In event of damage to the supply cable, the cable must only be replaced by the manufacturer or at an authorized service location, to avoid any potential risks.

• In case the installation instructions of a stove with a gas burner specifies a greater installation height, that distance shall be applied. Always observe the requirements applicable to air replacement.
  

USE

• Ensure adequate ventilation in the room, if the kitchen exhaust hood is used simultaneously with other appliances using gas or other fuel types (this does not apply to exhaust hoods, which return the air into the room when set to recycling ventilation).
• This exhaust hood is exclusively designed for household use, to eliminate smells in the kitchen.
• Never use the exhaust hood for purposes other than designated.
• Never leave a high open flame burning under the exhaust hood.
• Set the flame intensity so that it is directed towards the bottom of the pan, and it does not extend around the sides.
• Fryers should be continuously monitored during use: oil can catch fire, if overheated.
• Avoid the use of open flames under the exhaust hood, as this presents a risk of fire.
• This appliance can be used by children aged 8 years or above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge, provided that they are supervised or have been given instructions concerning the safe use of the appliance and understand the hazards involved.
• Keep children supervised. Do not allow children to play with the appliance.
• Cleaning and user maintenance may not be carried out by children without proper supervision.
• CAUTION: Accessible parts of the exhaust hood may become hot, if used together with cooking appliances.
  

MAINTENANCE

• Regularly clean the kitchen exhaust hood and its filter, according to the given instructions.
• Before starting any maintenance work on the appliance, disconnect the plug from the mains socket.
• Clean the exhaust hood with a moistened cloth and neutral liquid detergent.
• This appliance serves up to 4 cooktop units.

DISPOSAL

Waste equipment must be collected and disposed separately from household waste because it may contain components hazardous to the environment or health. Used or waste equipment may be dropped off free of charge at the point of sale, or at any distributor which sells equipment of identical nature and function. Dispose of product at a facility specializing in the collection of electronic waste. By doing so, you will protect the environment as well as the health of others and yourself. If you have any questions, contact the local waste management organization. We shall undertake the tasks imposed upon the manufacturer pursuant to the relevant regulations and shall bear all associated costs arising from such.

MAIN PARAMETERS

Rated voltage and frequency: 220–240 V~ / 50 Hz
Drive motor rated input: 105 W
Grease filter: KPE 6090/A
Carbon filter set (2 pcs): KPE 6090/C
Under certain circumstances, electric appliances carry a risk.

PARTS

DIMENSIONS

DRILLING AND MINTING THE BRACKET

Firstly, prepare the following drawings:

• Draw a vertical line running up to the ceiling, or the top boundary in the centreline of the area, where the a exhaust canopy will be installed.
• Draw a horizontal line A at a height of 1270–1560 mm above the cooktop.
• Draw a horizontal line B at a height of at least 887 (840 optional) mm above the cooktop.
• Draw a horizontal line C at a height of at least 717 mm above the cooktop

Marking points

• Mark a point (1) on horizontal line A, at a distance of 40 mm to the right of the vertical reference line.
• Repeat the same on the other side, and verify, whether the two marks are in level.
• Mark a point (2) on horizontal line B, at a distance of 80 (135 optional) mm to the right of the vertical reference line.
• Repeat the same on the other side, and on the vertical reference line, and verify, whether the three marks are in level.
• Mark a point (3) on horizontal line C, at a distance of 112.5 mm to the right of the vertical reference line.
• Repeat the same on the other side, and verify, whether the two marks are on the same horizontal line.

Installation of brackets:

• Drill a hole at the marked points (1) (2) (3), with a ∅10 mm drill bit.
• Fit the dowels 11 into the holes (1) (2) (3).
• Install the exhaust hood mounting bracket 20 with the 3 bolts 10 (5 x 50) included.
• Install the cover sheet fastening bracket 21 with the 2 bolts 10 (5 x 50) included.

Hang the exhaust hood on the wall:

• Fold down the glass panel by pulling the bottom edge towards yourself. When folded down, it should be hanging vertically by its top edge.

• Remove the metal grease filter from behind the glass panel.

• Hang the exhaust hood on the mounting bracket 20. • Level the exhaust hood horizontally.
  

• Fasten the bolts 10 into the dowels 11 at the marked points (3) through the inside of the exhaust hood.

• Place the metal grease filter back.

• Close back the glass panel by pushing the bottom edge towards the wall until secured.

SELECT THE VENTILATION MODE

Two ventilation modes are available, exhaust ventilation mode and recycling ventilation mode. Select the desired operation mode before installation of the appliance.

In case of exhaust ventilation mode, air is removed from the room through an exhaust pipe.

In case of recycling ventilation mode, air is cleaned and returned back into the room through the two rows of holes located on the decorative cover.

Notes: In case of recycling ventilation mode an exhaust pipe is not required. Fit carbon filters into the unit. With the carbon filter installed, suction rate reduces.

• Recycling ventilation mode
  

• Exhaust ventilation mode
  

CONNECTIONS

EXHAUST VENTILATION SYSTEM WITH AIR DUCT

In case of installation of a version with an air duct, connect the exhaust hood to the air duct with a ∅150 or ∅120 mm flexible or rigid pipe, to be selected by the fitter.

• To install a ∅120 mm exhaust connection, fit the reducer 3 to the outlet of the exhaust hood.
• Fasten the pipe 4 using adequate clamps (not included in the package).
• Remove any fitted activated carbon filters.
  

ASSEMBLY OF THE COVER SHEET

The cover sheet can only be installed together with the exhaust hood.

Decorative cover sheet, bottom part

•  Install the cover sheet fastening bracket 21 to the bottom part of the decorative cover sheet with the 2 bolts 12 (4.2 x 9.5) included with the exhaust canopy.
  

• Hang the brackets 13 on the canopy body and fasten them with 2 bolts 12 (4.2 x 9.5) so that they rest evenly.

• Slightly widen the two sides of the bottom cover sheet, then hang it between the brackets 13, and fasten the cover sheet to the brackets 13 with the 2 bolts 12 (4.2 x 9.5) included.
  

Decorative cover sheet, top part

• Slightly widen the two sides of the top cover sheet, then hang it between the wall and the bracket 21, which is fastened to the bottom part of the decorative cover sheet.
• Fasten the top cover sheet to the bracket 21 with the 2 bolts 12 (4.2 x 9.5) included.
  

USE

CONTROL PANEL

When is lit.
Switching the drive motor and lighting OFF.| When is flashing.

MAINTENANCE

GREASE FILTER

CLEANING THE METAL SELF-SUPPORTED GREASE FILTER

• The filter needs to be cleaned every 2 months, or even more frequently, especially in case of excessive use. The filter can be cleaned in a dish-washer.
• Fold down the glass panel.
• Remove the metal grease filter.
• Avoid bending the filter in any way when washing. Before placing back into the exhaust hood, ensure that it is completely dry. (The colour of the filter surface will change with time, but this does not affect the efficiency of the filter itself).
• When placing the filter back, ensure that it is positioned correctly.
• Close the glass panel back.
  

ACTIVATED CARBON FILTER (RECYCLING VENTILATION VERSION)

These filters are not washable or recyclable, therefore they need to be replaced approximately every 4 months, or more frequently in case of excessive use.

REPLACING THE ACTIVATED CARBON FILTER

• Fold down the glass panel.
• Remove the metal grease filter.
• Remove the saturated active-carbon filter.
• Fit the new filters.
• Place the metal grease filter back.
• Close the glass panel.
  

LIGHTING

REPLACING THE LAMP

• Turn off the exhaust hood and disconnect the plug from the mains socket, or switch off the cut-out, or fuse.
• Remove the grease filter.
• Apply tension on the lamp and remove it from its holder (this might require the exertion of pressure or force).
• Disconnect the lamp connector.
• Replace the lamp with a new one of equivalent type, and ensure that it is correctly connected to the connector.
• Reconnect the power supply by plugging the supply cable plug into the wall socket, or by switching the cut-out, or fuse back on.

| Maximum output| Voltage| | Lamp base| ILCOS D code
---|---|---|---|---|---
Separate adapter of LED modules| 1,5 W| DC 12 V| Rectangle:

33.2 mm x 120 mm

| | DBS-1.5-H-33.2/120

Check the blades.
The condenser is damaged.| Replace the condenser.
The drive motor is damaged.| Replace the drive motor.
The internal wiring of the drive motor is cut off / disconnected. There is an unpleasant smell present.| Replace the drive motor.
Neither the lighting, nor the drive motor run.| In addition to the above, check the following:
The lighting is damaged.| Replace the lamps.
The supply cable is loosened.| Connect the cable according to the wiring diagram.
Oil leak present.| The outlet and the inlet of the vent are not sealed properly.| Remove the outlet and seal with adhesive sealant.
Vibration occurs.| The blade can cause vibration, if damaged.| Replace the blade.
The drive motor is not fastened tightly.| Fasten the drive motor tightly.
The exhaust hood is not fastened tightly.| Fasten the exhaust hood tightly.
Insufficient suction.| The distance between the exhaust hood and cooktop is too big.| Readjust the distance.
Too much ventilation due to opened doors or windows.| Select a new location for the installation of the appliance, or close some of the doors/windows.
The appliance is askew.| Mounting bolts are not tightened enough.| Tighten the mounting bolts and adjust the appliance horizontally.
Hangers are not tightened enough.| Tighten the hangers and adjust the appliance horizontally.

Customer Support

Producer
SOMOGYI ELEKTRONIC® • H – 9027 • Győr, Gesztenyefa út 3. • www.somogyi.hu

Distributor: SOMOGYI ELEKTRONIC SLOVAKIA s. r. about.
Ul. gen. Klapku 77, 945 01 Komárno, SK • Tel.: +421/0/35 7902400 • www.somogyi.sk

Distributor: S.C. SOMOGYI ELECTRONICS S.R.L.
J12/2014/13.06.2006 C.U.I.: RO 18761195
Cluj-Napoca, Cluj County, Romania, Str. Prof. Dr. Gheorghe Marinescu, no. 2, Postal code: 400337
Tel.: +40 264 406 488, Fax: +40 264 406 489 • www.somogyi.ro

Importer for Serbia: ELEMENTA d.o.o.
Jovana Mikića 56, 24000 Subotica, Serbia • Tel:+381(0)24 686 270 • www.elementa.rs
Country of import: Hungary • Country of origin: China • Manufacturer: Somogyi Elektronic Kft.

Importer for HR: ZED d.o.o.
Industrial c. 5, 10360 Sesvete, Croatia • Tel: +385 1 2006 148 • www.zed.hr
Importer for BiH: DIGITALIS d.o.o.
M.Spahe 2A/30, 72290 Novi Travnik, BiH • Tel: +387 61 095 095 • www.digitalis.ba
Manufacturer: Somogyi Elektronic Kft, Gesztenyefa ut 3, 9027 Gyor, Hungary

References

• Digitalis d.o.o.
• Somogyi Elektronic Kft.
• Somogyi Elektronic S.R.L.
• Somogyi Elektronic Slovensko s.r.o..
• Zed d.o.o.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>