KYNAST 613-401183 Cordless Drill Instruction Manual

KYNAST 613-401183 Cordless Drill

Introduction
To get the most out of your new cordless drill, please read through these instructions and the attached safety instructions before use. Please also save the instructions in case you need to refer to them at a later date.

General safety warnings

Read all safety warnings and all instructions. Failure to follow the warnings and instructions may result in electric shock, fire and/or serious injury.
Save all warnings and instructions for future reference. The term “power tool” in the warnings refers to your mains operated (corded) power tool or battery- operated (cordless) power tool.

Work area safety

• Keep work area clean and well lit. Cluttered or dark areas invite accidents.
• Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gases or dust. Power tools create sparks which may ignite the dust or fumes.
• Keep children and bystanders away while operating a power tool. Distractions can cause you to lose control.

Technical data

• Cordless drill
• Battery: 12 V 1.3 AH Li-ion
• Charging time: 1 hour
• Gears: 1
• Speed: 0-650 rpm
• Torque: Max. 20 Nm
• Torque settings: 18+1
• Chuck: 10 mm
• With LED work light and 1-hour charger
• Sound pressure, LpA: 81.5 dB(A), K pA = 5 dB(A)
• Sound level, L WA : 92.5 dB(A), K WA = 5 dB(A)
• Vibration: Ah,D: 1.228 m/s2 K= 1.5 m/s2

Electrical safety

• Power tool plugs must match the outlet. Never modify the plug in any way. Do not use any adapter plugs with earthed (grounded) power tools. Unmodified plugs and matching outlets will reduce risk of electric shock.

• Avoid body contact with earthed or grounded surfaces, such as pipes, radiators, ranges and refrigerators. There is an increased risk of electric shock if your body is earthed or grounded.

• Do not expose power tools to rain or wet conditions. Water entering a power tool will increase the risk of electric shock.

• Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the power tool. Keep cord away from heat, oil, sharp edges and moving parts. Damaged or entangled cords increase the risk of electric shock.

• When operating a power tool outdoors, use an extension cord suitable for outdoor use. Use of a cord suitable for outdoor use reduces the risk of electric shock.

• If operating a power tool in a damp location is unavoidable, use a residual current device (RCD) protected supply. Use of an RCD reduces the risk of electric shock.
  Personal safety

• Stay alert, watch what you are doing and use common sense when operating a power tool. Do not use a power tool while you are tired or under the influence of drugs, alcohol or medication. A moment of inattention while operating power tools may result in serious personal injury.

• Use personal protective equipment. Always wear eye protection. Protective equipment such as dust mask, non-skid safety shoes, hard hat, or hearing protection used for appropriate conditions will reduce personal injuries.

• Prevent unintentional starting. Ensure the switch is in the off position before connecting to power source and/or battery pack, picking up or carrying the tool. Carrying power tools with your finger on the switch or energising power tools that have the switch on invites accidents.

• Remove any adjusting key or wrench before turning the power tool on. A wrench or a key left attached to a rotating part of the power tool may result in personal injury.

• Do not overreach. Keep proper footing and balance at all times. This enables better control of the power tool in unexpected situations.

• Dress properly. Do not wear loose clothing or jewellery. Keep your hair, clothing and gloves away from moving parts. Loose clothes, jewellery or long hair can be caught in mo ving parts.

• If devices are provided for the connection of dust extraction and collection facilities, ensure these are connected and properly used. Use of dust collection can reduce dust-related hazards.

Power tool use and care

• Do not force the power tool. Use the correct power tool for your application. The correct power tool will do the job better and safer at the rate for which it was designed.

• Do not use the power tool if the switch does not turn it on and off. Any power tool that cannot be controlled with the switch is dangerous and must be repaired.

• Disconnect the plug from the power source and/or the battery pack from the power tool before making any adjustments, changing accessories, or storing power tools. Such preventive safety measures reduce the risk of starting the power tool accidentally.

• Store idle power tools out of the  reach of children and do not allow persons unfamiliar with the power tool or these instructions to operate the power tool. Po  wer tools are dangerous in the hands of untrained users.

• Maintain power tools. Check for misalignment or binding of moving parts, breakage of parts and any other condition that may affect the power tool’s operation. If damaged, have the power tool repaired before use. Many accidents are caused by poorly maintained power tools.

• Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting edges are less likely to bind and are easier to control.

• Use the power tool, accessories, and tool bits etc. in accordance with these instructions, taking into account the working conditions and the work to be performed. Use of the power tool for operations different from those intended could result in a hazardous situation.
  Service

• Have your power tool serviced by a qualified repair person using only identical replacement parts. This will ensure that the safety of the power tool is maintained.

• Never service damaged battery packs. Service of battery packs should only be performed by the manufacturer or authorized service providers.
  Battery tool use and care

• Recharge only with the charger specified by the manufacturer. A charger that is suitable for one type of battery pack may create a risk of fire when used with another battery pack.

• Use power tools only with specifically designated battery packs. Use of any other battery packs may create a risk of injury and fire.

• When battery pack is not in use, keep it away from other metal objects, like paper clips, coins, keys, nails, screws or other small metal objects, that can make a connection from one terminal to another. Shorting the battery terminals together may cause burns or a fire.

• Under abusive conditions, liquid may be ejected from the battery; avoid contact. If contact accidentally occurs, flush with water. If liquid contacts eyes, additionally seek medical help. Liquid ejected from the battery may cause irritation or burns.

• Do not use a battery pack or tool that is damaged or modified. Damaged
  or modified batteries may exhibit unpredictable behaviour resulting in fire, explosion or risk of injury.

• Do not expose a battery pack or tool to fire or excessive temperature. Exposure to fire or temperature above 130 °C may cause explosion.

• Follow all charging instructions and do not charge the battery pack or tool outside the temperature range specified in the instructions. Charging improperly or at temperatures outside the specified range may damage the battery and increase the risk of fire.

Special safety instructions

• Use the charger at room temperature only (max. 40° C).
• Never use the charger if the battery, charger or cord is damaged.
• Check that the air vents on the cordless drill are not blocked.
• Do not use damaged or worn drill and screw bits and always select the correct type of bit for the job.
• Secure small items in a vice or similar. Never hold the item in your hand!
• Check for concealed power cables, pipes, etc. in the items or surfaces you are going to drill.
• Place a piece of scrap wood under the item if possible. Make sure that the drill does not damage any objects under or behind the item, e.g. when drilling into walls.
• The drill must not be in contact with anything when it is started.
• Drilling certain materials can produce harmful dust. Always wear a mask.
• Ensure the drill has completely stopped before changing direction.
• Never put the drill down if the bit is still rotating. Wait until it has stopped completely before putting it down if you are not going to use it again.
• Avoid touching the drill bit immediately after use. It may be very hot.
• This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of
• experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the
• hazards involved. Children shall not play with the appliance. Cleaning and user maintenance shall not be made by children without supervision (EN 60335-1:2012 cl.7.12).

Die Teile der Akku-Bohrmaschine

1. Self-tightening drill chuck
2. Torque selector (18 settings+drilling)
3. Direction selector
4. Handle
5. Release button
6. Battery
7. On/off button (variable)
8. LED work light
9. Charging

Charging and fitting the battery

Charge the battery fully before using the drill for the first time. Press the release button (5) on the battery (6) and take the battery out. Insert the plug from the charger into the charging socket on the battery. Plug the charger in. The LED on the charger will light up red while the battery is charging. Once the LED turns green, the battery is fully charged. Charging takes approx. 1 hour. Disconnect the charger from the mains once the battery is charged and insert it into the drill.

Make sure the release button engages so that the battery is firmly in place.
NB! The battery is not fully charged on delivery. It must be charged for about 3 hours prior to use. After that, charging takes 1 hour. The battery cannot reach full capacity until it has been charged and discharged around 5 times.

Preparation

Changing bits
Switch the direction selector (3) to its centre position.
Turn the chuck (1) by hand to open the jaws of the chuck. Insert the required drill bit into the chuck and retighten.
Check that the bit is in the centre of the chuck and is secure.

Selecting direction
Select direction (left or right) using the switch (3).
If the switch is placed in the centre position, the on/off button cannot be pressed in and the drill cannot be started.

Selecting torque
Select the torque by turning the torque selector (2) to the required position. The higher the setting, the higher the torque applied. To drill, turn the torque selector to the position with the drill symbol.

Use

Fit a suitable drill or bit for the task. Select gear, direction and torque.
Start the drill by pressing the on/off button (7). The more the button is depressed, the faster the chuck will revolve. The LED work light (8) comes on and lights up the working area when you press the on/off button.
Allow the drill to reach full speed before starting to drill.
Do not press the drill too hard. Select a low speed for screwing, large drill bits or hard materials and a higher speed for small drill bits or softer materials. Switch off by releasing the on/off button.

Useful tips for drilling

• When drilling in smooth surfaces, e.g. tiles, stick a piece of strong tape on the drilling point before drilling to prevent the bit slipping.
• Always centre-punch the drilling point first when drilling steel.
• Place a piece of scrap wood under the item when drilling thin sheet metal to avoid deforming the sheet.
• Lubricate the drilling point with oil when drilling into metal. Use machine oil for steel and paraffin oil for aluminium.
• To avoid splinters when drilling wood or plastic, place a piece of scrap wood under the item or drill from both sides.
• Use a high speed drill bit when drilling plastic.
• For large holes, start with a small diameter drill and then move up to the desired diameter.

Cleaning and maintenance

Clean the drill with a slightly damp cloth or compressed air after use and always keep all surfaces and ventilation slots free from dust.
Never use corrosive or abrasive cleaning agents, as they may attack the plastic parts of the drill.

Guarantee and service
Our products undergo a strict quality control process before delivery. If the product has unexpectedly been damaged or developed a defect during production or transport, please return it to the retailer. You can legally make a claim under the guarantee in the following circumstances:
The product is covered by a 2-year guarantee from the date of purchase. During this period, we will repair or replace the product if it is found to be defective due to material or production faults.
Faults caused by incorrect use or handling, faults caused by unauthorised intervention or repairs, and faults caused by use of non-original parts are not covered by the guarantee.

Correct disposal

The symbol above and on the product means that the product is classed as Electrical or Electronic equipment and should not be disposed with other household or commercial waste at the end of its useful life. The Waste of Electrical and Electronic WEEE: DE 18770614 Equipment (WEEE) Directive (2012/19/EU) has been put in place to recycle products using best available recovery and recycling techniques to minimise the impact on the environment, treat any hazardous substances and avoid the increasing landfill. Contact local authorities for information on the correct disposal of Electrical or Electronic equipment.

EC Declaration of Conformity

Authorised representative: Schou Company A/S, Nordager 31, 6000 Kolding, Denmark, hereby declares that has been manufactured in accordance with the following standards or normative documents:
EN 62841-1:2015
EN 62841-2-1:2018
EN 60335-1:2012+A11:2014
EN 60335-2-29:2004+A2:2010
EN 62233:2008
EN 55014-1:2017
EN 55014-2:2015
EN 61000-3-2:2014
EN 61000-3-3:2013
in accordance with the provisions of the following directives
2006/42/EC The Machinery Directive
2014/35/EU The Low Voltage Directive
2014/30/EU The EMC Directive
1907/2006/EU The REACH regulation
2011/65/EU The RoHS Directive

References

• EXPO-BÖRSE | STARTSEITE

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>