American Weigh Scales AWS AXIS-100 Pocket Scale USER GUIDE

American Weigh Scales AWS AXIS-100 Pocket Scale

INTRODUCTION

A digital pocket scale with the highest level of portability is the AXIS-100. Pushing a button reveals the LCD and control panel, allowing the scale to maintain a slim profile while not in use. You can manage a range of weighing jobs thanks to the two extension trays that are supplied. In order to increase security and portability, the trays also house the scale. You can precisely weigh amounts of food like cereal, fruit, salads, and more with the help of these special scales. The tare feature on the four-button operation allows you to deduct the weight of the bowl from the weight of the actual contents for consistently accurate measurements.

SPECIFICATION

• DIMENSIONS: 4 x 4.0 x 0.8 in.
• WEIGHT: 53 ounces
• BATTERIES: 2 AAA
• COLOR: Black
• CAPACITY : 100g 600g
• READABILITY: 01g 0.1g
• WEIGHT: 0.03g 0.2g
• POWER: 2 x 1.5V “AAA” Alkaline
• PLATFORM DIMENSIONS: Ø 2.8” in.

AXIS Manual

Thank you for purchasing the American Weigh AXIS digital pocket scale. Please read all operating instructions carefully before use. Scales are precision measuring devices and should always be handled with proper care. To ensure years of reliable service, keep these simple tips in mind:

• Do not exceed the scale’s maximum capacity. This scale has integrated overload protection, but any overload protection has its limits!
• Avoid exposure to extreme heat or cold. Scales perform best at normal room temperature. If temperatures have changed dramatically, recalibration may be necessary.
• Allow your scale to warm up for 30-60 seconds before performing calibration (if available).
• Store your scale in a clean, dry location. Dust, dirt, and moisture can accumulate on the weighing sensors and electronics causing inaccuracy or malfunction.
• Avoid using your scale in close proximity to strong radio wave emitting devices such as cordless phones.
• Always weigh on a flat and level surface, free from vibrations and drafts. The corner of a room is usually the most stable.
• Gently apply all items to be weighed. Do not drop items onto the weighing platform.
• Avoid dropping your scale. The warranty does not cover damage due to rough treatment or overload.
• Check the batteries first if you are having any trouble with your scale. This simple step can remedy most scale issues.
• Calibration should be checked and adjusted occasionally as part of routine scale maintenance.

Part List

1. Scale
2. Cover / Expansion Tray (1 Large, 1 Small)
3. AAA Batteries (x2)

**Key Description

**

1. C/R Key – Tap to enter Counting Mode. Hold to set the piece weight and sample size.
2. Mode Key – Tap to change the weighing unit. Hold to enter calibration (see section VIII)
3. Tare Key – Re-zero the scale. Used to remove the weight of a container.
4. Power Key – Turns the scale on or off.

Battery Installation

Low batteries can cause inaccuracies in digital scales. If you are experiencing issues with your scale, first try new batteries. Most times, this will solve the problem.

1. Before using the scale for the first time, check the battery compartment and remove any plastic insulation strips or packaging that may be in place to prevent battery drainage during shipping/storage.
2. If you are replacing the batteries, make sure the positive and negative contacts are properly aligned.

Operation

1. Place the scale on a flat, level surface and press the power key to turn the scale on.
2. Once the start-up process completes and the scale goes to zero you are ready to weigh.
3. Place the quantity to be weighed onto the weighing platform.
4. Wait a couple seconds for the display to stabilize before taking a weight reading.
5. To turn the scale OFF, press the key again.

Changing the Unit of Measure

1. Press the M key to change the scales displayed unit of measure.
2. If the scale is turned off then back on, it will default to the last unit used.

Using the Counting Feature

This scale can be used to count items of uniform weight. To use the counting feature, follow these instruction:

1. First manually count out a sample quantity of either 25, 50, 75, or 100pcs.
2. With the scale on, place the sample quantity on the platform then hold the C/R key until a number is displayed.
3. Press the M key to change the displayed number to match the sample quantity you placed on the platform (must be 25, 50, 75, or 100)then press the C/R key to confirm it.
4. The display will then show the current count. The count will update as you add or remove items.
5. To return to normal weighing mode, press the C/R key again.

Using the Tare Feature

You can use this scale’s tare feature to subtract the weight of an empty container or vessel for net weight determination. NOTE: The weight of the container will subtract from the available capacity (subtractive taring).

1. Place the empty container or vessel on the weighing platform.
2. Press the T key once. The display will then reset to zero. If the container is removed, its weight will be displayed as a negative number.
3. You may now fill the container with the quantity to be weighed. The display will show the net weight of the contents.
4. To return to normal weight display (gross weight), remove any items from the weighing platform and press the T key again to re-zero the scale.

Calibration

Initial calibration is performed at the factory. However, the calibration can drift slightly due to stresses from shipping. Also, due to changes in local acceleration of gravity around the world, adjustment is recommended when moving the scale from one location to another. To check calibration:

1. Place the required calibration weight on the scale and note the displayed value.
2. If the displayed value is not within acceptable tolerance (see chart on next page), adjustment is required.

Adjustment

1. With the scale on, press and hold the M key until the display shows “CAL”.
2. Make sure nothing is on the weighing platform then press the M key again. The display will flash “CAL” followed by the required calibration weight (see chart on previous page).
3. Place the required calibration weight on the center of the platform.
4. Once the weight has stabilized, the scale will show “PASS” then return to normal weighing mode. Calibration is complete!

Troubleshooting

• Problem: Scale will not turn on
• Solution: Check the batteries and battery contacts.
• Problem: Displayed weight fluctuates randomly
• Solution: Make sure your workspace is stable and free of any air currents or vibration. In some cases, nearby radio wave emitting devices can cause fluctuations.
• Problem: Displayed weight is inaccurate
• Solution: Perform a calibration adjustment. If you are still having trouble, contact our warranty department.

Error Codes

1. OUTZ – Zero point has drifted out of the acceptable range. Try to perform a calibration adjustment. If the problem persists, the load cell may be permanently damaged due to overloading.
2. O-Ld – Overload. The maximum capacity has been exceeded. Remove the extra weight to avoid permanently damaging the load cell.
3. Lo – Batteries are low. Replace the batteries.

**Capacity/Readability Charts

**

FREQUENTLY ASKED QUESTIONS

How do I reset my AWS 100 scale?

Press the Tare button on the front to reset the scale to zero if there is nothing on it right now but it still displays a number or is negative. Even if there is something on the weighing platform right now, doing this will reset it as well.

How do I calibrate my AWS pocket scale?

As soon as you get the right number of nickels on the scale, press the calibration button. Calibration often requires some time, and during calibration, the digital readout will flash. The number of weights you need to add will depend on the scale. Make certain that you have enough nickels on hand in advance.

How do you use a pocket digital scale?

Place the scale on a flat, level surface and activate it by pressing the [ON/OFF] key. When “0.0” appears, you are prepared to weigh. The item(s) should be placed on the weighing platform. Take a weight reading after waiting a short while for the display to stabilize.

How do you calibrate a 100 gram scale?

Switch on the scale. Wait until the LCD says “0.0,” then press and hold the [M] key for three to five seconds until the LCD says “CAL,” and then let go of the [M] key. When you press the [M] key, “CAL” will flash on the display, followed by the necessary calibration weight.

How do I reset my digital pocket scale?

Press the ON/OFF button to reset the device, and then wait until “0.0” appears. 2. When “CAL” appears, press and hold the UNITS button for 3 seconds.

How do I fix scale error?

Old batteries should be removed from the scale’s rear. Put in 4 fresh AA batteries. Duracell batteries are advised by the scale’s maker. Be sure to reset the scale before weighing again.

Why is my digital scale not working?

Issues with the display and functionality of digital scales are frequently caused by batteries. Remove the batteries by carefully opening the battery compartment. Clear the compartment of any dust or other objects that could obstruct the battery connection using a small, clean paintbrush or cotton swab.

Why does my digital scale keep jumping?

Your scale may fluctuate for a variety of reasons. Low battery, using it on an uneven surface, overloading, grime buildup, moving while using, and water damage are a few of the most frequent causes.

How accurate are pocket scales?

With a reading of up to 0.01 grams, digital pocket scales are also remarkably precise for their size. For practically any non-scientific measurement, that is accurate enough. Most are also incredibly simple to calibrate, so they’re never more than a few seconds away from a trustworthy readout.

How do I know if my scale is accurate?

Note the weight of a coin after placing it on the scale. Put one more nickel on the scale, and then record the updated weight. One additional nickel can be added to the scale; record the weight. The weight should have increased by 5g each time if your scale is accurate.

What are the two types of weighing scale?

Scales go into one of two categories: mechanical weighing scales. Digital scales for weighing.

Why do I weigh more on digital scales?

This is necessary for the scale to display your weight accurately. Your body weight will be dispersed over the material’s individual fibers as opposed to being concentrated on the scale itself if you place the scale on a softer surface, such a towel or carpeted floor.

How do you fix an inaccurate scale?

If your scale is lying on an uneven, slanted, or rounded surface, it may display irregular readings even if it is calibrated. To settle the scale and guarantee accurate readings each time, place a mouse pad or static-reducing pad on a level, firm surface underneath the scale.

VIDEO

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>