nanoleaf 374UBSK7PN Shapes Ultra Black Triangles Smarter Kit

Product Information

Specifications

• Product Name: Nanoleaf Shapes Triangles Smarter Kit
• Components: Light Panels, Mounting Plates, Linkers, Controller, Mounting Tape, Power Supply
• Power Supply: Each standard PSU supports up to 42W
• Controller Capacity: Supports up to 500 panels

Product Usage Instructions

Installation Tips:

• Ensure you have enough power supplies for your layout.
• Clean the mounting surface to remove dust, moisture, and oil before installation.
• To mount panels, apply strong pressure in a circular motion to the center of the panel for 30 seconds.
• The Controller and Power Supply can be connected to any panel in your setup.
• Avoid using tape on textured, porous, popcorn, or ceiling surfaces.

Warnings & Cautions:

Please read the safety information carefully and keep this document for future reference. Ensure that the product is not used in environments exceeding 40 degrees Celsius, wet or damp conditions, or excessively hot or humid areas. Do not place metallic or conductive objects near any exposed metal contacts. Unplug the power supply before dismounting light panels. Keep small children away from the device as it may contain small parts that pose a choking hazard.

FAQ

Q: Can I use the Nanoleaf Shapes Triangles outdoors?

A: It is not recommended to use the product outdoors in wet or damp conditions or in extreme temperatures.

Q: How many panels can the Controller support?

A: The Controller supports up to 500 panels.

User Manual & Warranty Registration
nanoleaf.me/myshapes

Important Installation Tips

• * Make sure you have enough PSUs for your layout. NOTE: Each standard PSU supports up to 42W and each Controller supports up to 500 panels. Use our PSU calculator at [nanoleaf.me/myshapes](http://nanoleaf.me/myshapes).

• Before mounting your panels, clean your surface to be free of dust, moisture and oil.

• To mount, apply strong pressure in a circular motion to the center of the panel for 30 seconds.

• The Controller and Power Supply can be connected to any panel in your setup.

• Tape is NOT suitable for textured, porous, popcorn and ceiling surfaces (ie. wallpaper or brick walls).

INSTALLATION

WARNINGS & CAUTIONS

• Please read this safety information carefully and keep this document for future reference. Help articles and customer support is always available at https://helpdesk.nanoleaf.me.
• This Nanoleaf® product is not designed, certified, nor intended for use in: enclosed locations that limit the flow of air and/or trap heat which contributes to an environment temperature over 40 degrees Celsius; emergency exits, emergency lighting, or other use cases involving critical systems for human safety; in conjunction with 3rd party devices that are not approved by Nanoleaf® for use with Nanoleaf® products; locations or use cases where there is a risk of electric shock; outdoor areas, regardless of weather conditions; wet or damp conditions; as a floor covering or floor tiling; excessively hot environments that are consistently above 40 degrees Celsius for extended periods of time (for example: near ovens, space heaters, clothing dryers); excessively humid areas; regions or countries other than that in which the product was intended for and certified for sale in.
• When using this Nanoleaf® products, do not open or disassemble the device, as this will void the warranty and make the product unsafe for use. While connected to the electrical supply of the building, line voltages will be present in the power supply, panels, linkers, so do not place any metallic or conductive objects near any exposed metal contacts on any component.
• Unplug the power supply unit from the power source before dismounting light panels.
• Do not allow small children to operate this device without adult supervision.
• This device contains small parts that may be a choking hazard to small children. Loose or dangling cords may cause an entanglement hazard to small children.
• Do not leave cords dangling or loose on the floor to help prevent accidents from tripping.
• Do not clean the device with liquid or sprays when it is connected to power.
• Clean the panels with a soft dry cloth, and do not use harsh cleaning agents.
• Do not step on any part of the device, as this will cause breakage.
• Do not submerge any part of the device in water, or expose any part of the device to water.
• Do not bend or flex the panels with the connector still attached, as this will cause breakage.
• Do not attach the panels together with any connector or device other than original equipment manufactured by Nanoleaf®.
• Do not puncture any part of the device with sharp objects, as this will cause the device to cease working as designed and may present a safety hazard.
• If adhesive tape is a component of this product, please note that it is not designed to be used with brick wall, wallpaper, uneven/textured surfaces, or highly porous surfaces.
• Do not use double-sided tape to attach any part of the device to a ceiling or surface greater than 90 degrees relative to the floor, as the device will eventually fall down-creating a safety hazard and risk of damage to the device.
• Optional secure screw mounting solutions for these use cases are available, sometimes through added accessories offered for purchase separately.
• Your warranty DOES NOT COVER damage caused by falling devices. The flexible cable and power supply cannot be replaced by another third party product. If the cable is damaged, the entire controller and power supply should only be replaced with original equipment manufactured by Nanoleaf®. Using any non-approved replacement component will void the warranty and may present a serious safety hazard. Nanoleaf® light panels are primarily intended for decorative use, with RGBW output function that can dim.
• WI-FI/RF This equipment has been tested and found to comply with the limits of a Class B digital device, pursuant to part 15 of the FCC
• Rules and the Canadian ICES-003 Class B specifications. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
• This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
• However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/ TV technician or visit www.nanoleaf.me/support.

FREQUENCY RANGE

• 2.4GHz Wi-Fi: 2412-2462 MHz, Max RF e.i.r.p power < 20 dBm
• 2.4GHz Radio: 2402-2480 MHz, Max RF e.i.r.p power<10 dBm
• NFC: 13.56MHz, Max RF e.i.r.p power 0 dBm

CE INFORMATION

The external flexible cable or cord of this luminaire cannot be replaced; if the cord is damaged, the luminaire shall be destroyed. The light source contained in this luminaire shall only be replaced by the manufacturer or this service agent or a similar qualified person. NanoGrid Limited (Nanoleaf) hereby declares that this device is in compliance with the essential requirements and other relevant provisions of Directive 2014/53/EU. The declaration of conformity is available at www.nanoleaf.me/eudoc/.

WARRANTY INFORMATION

This product is covered by a limited warranty from Nanoleaf®: a two-year complimentary replacement of defective hardware. For full details visit: nanoleaf.me/warranty.

FCC STATEMENT

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment should be installed and operated with minimum distance of 20 cm between the radiator and your body.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/ TV technician for help.

MODIFICATION

Any changes or modifications not expressly approved by the grantee of this device could void the user’s authority to operate the device.

Still Need Help?
nanoleaf.me/support

Nanoleaf Canada

400 – 100 Front Street East

Toronto, ON
MSA 1E1, Canada

Nanoleaf Europe SAS
10 Rue du Capitaine Ferber
92130 Issy-les-Moulineaux
France

Nanoleaf Hong Kong
NanoGrid Limited

1301-483A Castle Peak Road,

Kowloon, Hong Kong

Model1:
NL47-7003TW· SPK
NL47-7003TW-7PK
NL47-0003TW- 9PK
NL47 0003TW-C

Power Supply Specs:
Input Voltage 120V AC 60Hz
Mox Power: 42W
Commul’IICotton Protocol.
Wi Ft (2.4GHz b, g/ n); 2 4GHz
proprietary
FCC ID: 2AEWY-NL42
IC: 20489-NL42

Models:
NL47-8003TW-12PK
NL47-3013TW-13PK
NL47-6003TW-15PK
NL47-5005TW-5PK
NL47-7005TW-7PK
NL47-0005TW-9PK
NL47-8005TW-12PK
NL47-6005TW-15PK
NL47-5017TW-5PK
NL47-7017TW-7PK
NL47-0017TW-9PK
NL47-8017TW-12PK
NL47-6017TW-15PK
NL47-0005TW-C
NL47-0017TW-C

Power Supply Specs:
Input Voltage: 100-240V-50/60Hz
Max Power: 42W
Communication Protocol:
Wi-Fi (2.4GHz b/g/n); 2.4GHz
proprietary

Smarter.
One of a kind.
Extraordinary.

References

• Nanoleaf® Official Site | Smart Home LED Lighting Products
• Nanoleaf® Official Site | Smart Home LED Lighting Products
• User Manual Shapes | Nanoleaf® (United States)

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>