HOOKE ROAD BXG.7014-S Gladiator JT Rear Inner Fender Liners Instruction Manual
- June 17, 2024
- HOOKE ROAD
Table of Contents
MAKE A DIFFERENCE
Rear Inner Fender liners
BXG.7014-S
Contents:
Driver Side| 
---|---
Passenger Side| 
Qty| PartName| Size(mm)| Picture
---|---|---|---
8| Hex Bolts| M825|
26| Button Head Socket Cap Bolts Screws| M610|
10| Button Head Socket Cap Bolts Screws| M48|
8| Flat Washer| M820*1.5|
2| Flange Hex Lock Nuts| M8|
10| Nylon Insert Lock Nut| M4|
18| Flange Hex Lock Nuts| M6|
Tool required:
a. Drive Socket Ratchet Wrench;
b. 3mm & 4mm& 5mm Hex Bit Socket;
c. 8mm & 10mm & 13mm Wrench;
Installation time:
About 2 hours, 1-2 people may be needed. Installation time may differ
according to your mechanical skill level.
(PLEASE VERIFY ALL PARTS ARE PRESENT AND READ INSTRUCTIONS CAREFULLY BEFORE
STARTING INSTALLATION!)
To view the electronic version (BXG.7014-S), please scan the QR code.
https://drive.google.com/drive/folders/1bHGvn6IpCJKgeVe3hZ-
nZj0oRfAFwZeL?usp=sharing
Installation instruction:
Rear Uninstall:
Step 1 : Use a 8mm socket to remove the bolts located along the interior
of the inner fender. Then, use a trim clip tool to remove the clips located in
each corner of the fender.
Step 2: Remove the fender flare by pulling the front section towards the
front of the vehicle, and the rear section towards the rear. Then pull the
fender directly “away” from the vehicle, to release the remaining clips. On
the JT, you should be able to reach around and squeeze the clips to remove if
needed.
Step 3: Use a trim
clip tool to remove the clips along the edge of the fender that remained in
the vehicle. Repeat process for the other side.
Passenger Side Installation:
Step 4: To install the decorative plate. Use the button head socket cap
bolts screws (M4*8), Nylon Insert Lock Nut (M4).
(5) M4*8 Button Head Socket Cap Bolts Screws (5)M4 Flange Hex Lock Nuts
Step 5: To assemble the passenger side rear inner fender liners (A2, B2,
C2, D2).
Use the button head socket cap bolts screws (M610), flange hex lock nuts
(M6). NOTE: The lip on the smaller inner piece will sit behind the outer
piece as shown in the image below.
Step 6: To install the connection
accessories. Use the button head socket cap bolts screws (M610). Step 7:
Once joined, place inner fender in inner wheel well. You will have to remove
most fenders to install.
Step
8: First, insert the two sides of the rear fender liners into the vehicle
body.
Then align the three installation holes at the bottom and secure them with the
factory screws without tightening the screws.
Step 9: Lift up the inner fender by hand. Line up
the holes on the upper of the inner fender. Use the hex bolts (M825), flat
washer (M8201.5). Don’t tighten up those bolts.
Step 10 : At last, line up the holes on the left of
the inner fender. Use the hex bolts (M825), flat washer (M8201.5). Tighten
up those bolts (step8, 9,10).
Step 11 : Repeat the same installation steps in the driver
side.
Step 12: The installation is complete. We hope you enjoy a wonderful off-
road life with this quality Hooke Road product!
Attention:
- The product parts in this instruction may differ slightly from the actual product contents but generally does not affect the installation of the product.
- Please feel free to contact your distributor if you have any kind of question about your purchase.
Google Hooke Road to find your parts.
Feel Free To Share Your Vehicle @HookeRoad4x4 With The Hashtag #hookeroad
If You’d Like
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>