true TBR TDR Series 72 Inch Bar Refrigerator Instruction Manual
- June 17, 2024
- TRUE
Table of Contents
true TBR TDR Series 72 Inch Bar Refrigerator
Product Information
Product Specifications
- Manufacturer: True Manufacturing Co., Inc.
- Model: TBR72-RISZ1-L-S-GGG
- Series: TBR | TDR
- Dimensions: Not specified
- Weight: Not specified
Installation Requirements
Appliance Specifications
The appliance specifications for the TBR72-RISZ1-L-S-GGG are not provided in the user manual. Please refer to the manufacturer’s website or contact True Manufacturing Co., Inc. for detailed specifications.
Clearances
The following clearances should be maintained during installation:
- Top: Not specified
- Sides: Not specified
- Back: Not specified
- Front: Not specified
- Bottom: Not specified
Electrical Requirements
The electrical requirements for the TBR72-RISZ1-L-S-GGG are as follows:
Electrical Installation & Safety
To ensure safe electrical installation, please follow these guidelines:
- Read and understand the electrical installation instructions provided by the manufacturer.
- Ensure the appliance is properly grounded.
- Use the correct voltage and amperage as specified in the electrical requirements.
- If unsure or unfamiliar with electrical work, consult a qualified electrician.
Warranty
Warranty Information
Warranty information for the TBR72-RISZ1-L-S-GGG is not provided in the user manual. Please refer to the manufacturer’s website or contact True Manufacturing Co., Inc. for warranty details.
FAQs
- Q: Where can I find the appliance’s full model name and serial number?
- A: The full model name and serial number are located on the appliance’s serial label. The exact location of the serial label may vary, so please refer to the appliance’s documentation or contact True Manufacturing Co., Inc. for assistance.
- Q: How can I find a qualified technician for installation or servicing?
- A: True Manufacturing Co., Inc. provides a Service Company Locator on their website at truemfg.com/support/service-locator. Please use this tool to find a qualified technician in your area.
True Manufacturing Co., Inc. TBR72-RISZ1-L-S-GGG
INSTALLATION MANUAL TBR | TDR SERIES
TBR32-RISZ1-L-B-S-1
TBR72-RISZ1-L-B-111-1
TDR48-RISZ1-L-B-SG
WARNING!
Be sure to read and fully understand this document before installing,
operating, maintaining or servicing this appliance. Failure to do so can
result in appliance failure, property damage, serious injury or death.
Appliance failure, injury or property damage due to improper installation is
not covered by warranty.
USER ACTION!
TRUE tracks the history of your appliance by its serial number. For easy
reference, record your appliances full model name and serial number below.
This information is on your serial label. Serial label location varies by
appliance.
Model Name:
Serial Number:
True Manufacturing Co., Inc.
2001 East Terra Lane · O’Fallon, Missouri 63366-4434
636-240-2400 · FAX: (636)-272-2408
International FAX: (636)-272-7546 · (800)-325-6152
Parts Department: (800)-424-TRUE (424-8783) Parts Department FAX:
(636)-272-9471
INSTALLATION MANUAL
TBR | TDR SERIES
Original Instructions
North America Canada and Caribbean Warranty Phone +1
855-878-9277 Warranty Fax +1
636-980-8510 Warranty Email
warrantyinquiries@truemfg.com
Technical Phone +1 855-372-1368
Technical Email service@truemfg.com 7:00 am6:00
pm CST MondayFriday, 8:00 am12:00 pm Saturday
TEC_TM_043 | REV. G | EN
Mexico Phone +52 555-804-6343/44
service-mexicocity@truemfg.com 9:00
am5:30 pm MF
Latin America Phone: +52
555-804-6343/44
servicelatam@truemfg.com 9:00 am5:30 pm
MF
UK, Ireland, Middle East, Africa & India Phone: +44 (0)
800-783-2049 Service-
emea@truemfg.com 8:30 am5:00 pm MF
Australia Phone: +61 2-9618-9999 service-aus@truemfg.com 8:30 am5:00 pm MF
01/23/2024
European Union & Commonwealth of Independent States Phone: +41 61-563-0705
service-emea@truemfg.com 8:00 am5:00 pm
MF
803294-G
TBR/TDR
THANK YOU
FOR YOUR PURCHASE
Congratulations!
The primary purpose of this document is to assist the installation,
maintenance, and servicing of your TRUE appliance. This document contains
information important to safety, operation, maintenance, and servicing. DO NOT
discard this document. TRUE is solely the appliance manufacturer. For
assistance finding a qualified technician, please visit our Service Company
Locator at truemfg.com/support/service-locator.
NOTICE!
Your appliance may not exactly match the figures shown in this manual.
Page 2 of 56
01/23/2024
P#803294
TEC_TM_043 | REV. G | EN
TBR/TDR
truemfg.com
Preface
The warning, guidelines, and recommendations within this document are meant to
prevent appliance damage, injury, or death. Please carefully read all
warnings, guidelines, and recommendations before proceeding to ensure the
continued safe use and maintenance of your TRUE appliance.
Signal & Symbol Definitions
Below are symbols you may see in this document. Some symbols may not appear.
DANGER! WARNING! CAUTION! USER ACTION!
NOTICE!
Signal Word Definitions
An imminently hazardous situation which, if not avoided, will result in
serious injury or death.
A potentially hazardous situation which, if not avoided, can result in serious
injury or death. A potentially hazardous situation which, if not avoided, may
result in minor or moderate injury; an unsafe practice. User action alert,
follow all recommendations to avoid appliance or product damage.
Important information not related to hazards or risk of personal injury.
Safety Symbols
Safety alert; alerts reader to potential physical injury hazards. Obey all
safety messages following this symbol to avoid possible injury or death.
Flammable material; fire hazard.
Additional Symbols
Mandatory action alert symbol; alerts reader to required or recommended
actions. Obey all messages and recommendations following this symbol to avoid
appliance or product damage.
NOTICE >
Important information not related to hazards or risk of personal injury.
Electrical shock hazard.
Review and understand the installation manual before installing, operating, or servicing.
Tipping hazard; tip-over hazard.
Wear eye protection.
Sharp element; cut or sever hazard.
Wear protective gloves.
Eye hazard; risk of eye injury.
Secure gas cylinders to prevent falling cylinders.
Exploding pressurized cylinder hazard.
DO NOT use extension cord.
Slippery surface hazard.
DO NOT use adaptor plugs.
Crush or cut hazard.
DO NOT dispose of with other household waste.
TEC_TM_043 | REV. G | EN
01/23/2024
Page 3 of 56
Important Safety Information
TBR/TDR
Important Safety Information
truemfg.com
Basic Safety & Operation Warnings
Follow basic safety precautions, including the following, to reduce risk of
personal injury, electric shock, fire, or death.
WARNING!
Be sure to read and fully understand this document before installing, operating, maintaining, or servicing this appliance.
Failure to do so can result in appliance failure, property damage, serious injury, or death. Appliance failure, personal
injury, or property damage due to improper installation is not covered by warranty.
· Failure to install, operate, and maintain the appliance as detailed in this document will negatively affect safety, appliance performance, component life, and warranty coverage.
· The appliance must be installed in accordance with all applicable laws, codes, and regulations.
· The manufacturer cannot be held responsible for injury or damage resulting from improper, incorrect, and unreasonable use.
· This appliance is not to be used, cleaned, or maintained by persons (including children) with reduced physical, sensory, or mental capabilities or lack of experience and knowledge, without proper supervision or instruction.
· DO NOT install or operate equipment that has been misused, abused, neglected, damaged, or altered/modified from original manufactured specifications.
· DO NOT modify or alter the appliance. Improper alterations can result in electric shock, personal injury, fire, or death.
· DO NOT use electrical appliances inside the food storage compartments of the appliance unless the appliances are approved by the manufacturer.
· The appliance owner is responsible for performing a Personal Protective Equipment (PPE) Hazard Assessment and to ensure adequate protection during maintenance and cleaning procedures.
· Use appropriate tools, safety equipment, and PPE during installation and servicing.
· Only use the appliance for its intended purpose as described in this document. Failure to do so may result in equipment damage, personal injury, or death.
· Overloading, incorrectly installing, or improperly loading shelves can cause shelf failure (as well as negatively affect the appliance’s operation), resulting in appliance damage, product damage, or personal injury.
· Keep the area surrounding the appliance clean to avoid appliance damage from debris or pests.
Page 4 of 56
01/23/2024
P#803294
TEC_TM_043 | REV. G | EN
Important Safety Information (cont.)
TBR/TDR
truemfg.com
Personal Injury Warnings
Only qualified technicians should install and service the appliance. For
assistance finding a qualified technician, please visit our Service Company
Locator at truemfg.com/support/service-locator. TRUE is solely the appliance
manufacturer and is not responsible for installation.
DANGER!
DO NOT allow children to play with or in the appliance. Child entrapment or personal injury can occur.
DO NOT store or use the following in the vicinity of this or any other appliance: · Gasoline or other flammable vapors and liquids · Combustible or explosive substances, such as aerosol cans with a flammable propellant · Other volatile or flammable substances
Contact TRUE Manufacturing to locate refrigerant lines and electrical wiring before drilling, cutting or puncturing interior or exterior walls. Failure to do so could result in damage, personal injury, or death.
WARNING!
Only qualified technicians should install and service the appliance. · Use
appropriate tools, safety equipment, and personal protective equipment (PPE)
during installation and servicing. · DO NOT touch the cold surfaces in the
freezer compartment when hands are damp or wet. Skin may stick to extremely
cold
surfaces.
This product can expose you to chemicals including Di-(2-Ethyl hexyl)
Phthalate (DEHP), which is known to the State of California to cause cancer
and birth defects or other reproductive harm. For more information go to
P65warnings.ca.gov.
Slippery Surfaces! Moisture from improper drainage can create slippery
surfaces near the appliance. It is your duty to immediately warn your
customers of, and dry, the slippery surface. All wet floor areas must be
marked with a wet floor sign.
Sharp edges! Take care when moving, installing, cleaning, servicing, and
maintaining the appliance to avoid cuts. Be sure to take care when reaching
under the appliance or handling metal components. · Keep fingers out of pinch
point areas, such as the space between appliance doors and surrounding
cabinetry. Take care
closing doors with children nearby.
Tip over hazard! Appliance may pose a tipping hazard when uncrating,
installing, or moving the appliance. Take appropriate safety precautions. Use
of tip over restraints may only reduce (not eliminate) the tipping hazard.
Never allow children to climb or hang on drawers, doors, or shelves.
Crush or cut hazard! Keep clear when uncrating, installing, moving, or
servicing the appliance.
Risk of electric shock or burn! See “Electrical Safety Warnings” for more
information.
TEC_TM_043 | REV. G | EN
01/23/2024
Page 5 of 56
Important Safety Information (cont.)
TBR/TDR
Hydrocarbon Refrigerant Warnings
TRUE appliances use hydrocarbon refrigerant (R-290/513A/600a). Check the
serial label to identify the appliance’s refrigerant. Serial label location
varies by model.
DANGER!
Risk of fire or explosion! Flammable refrigerant used.
· All servicing and maintenance must be performed by qualified technicians.
This is to minimize the risk of fire or personal injury due to incorrect parts
or improper service.
· Check the serial label to identify the appliance’s refrigerant. Serial label
location varies by model.
· DO NOT damage the refrigeration system during transportation and
installation.
· If the appliance is damaged, verify the refrigeration system’s integrity is
not compromised before proceeding.
· Never use sharp objects or tools to remove ice or frost. DO NOT use
mechanical devices to accelerate defrost.
· Dispose of in accordance with all applicable laws, codes, and regulations.
Follow all safety precautions associated with handling flammable refrigerant.
· DO NOT use electrical appliances inside the food storage compartments of the
appliances unless the appliances are of the type recommended by the
manufacturer.
Appliance Disposal Warnings
DANGER!
Risk of child entrapment!
Children can get trapped inside discarded appliances and suffocate. Never
dispose of your appliance without taking precautions to prevent child
entrapment, even if the appliance only sits unattended for a short period of
time.
Child entrapment precautions include the following:
· Remove all doors (or drawers for drawer appliances). · Leave all interior
drawers and shelving in place to make climbing (and fitting)
inside the appliance more difficult.
Risk of fire or explosion! Flammable refrigerant and insulation used. Dispose
of in accordance with all applicable laws, codes, and regulations. Follow all
safety precautions associated with handling flammable refrigerant and
insulation.
DO NOT dispose of your appliance with household waste.
Page 6 of 56
01/23/2024
P#803294
TEC_TM_043 | REV. G | EN
Important Safety Information (cont.)
TBR/TDR
truemfg.com
Electrical Safety Warnings
WARNING!
Risk of electric shock, burn, or fire!
· It is the appliance owner’s responsibility to ensure the electrical
connection meets all applicable building codes. Failure to meet these code
requirements can result in appliance damage, fire, electric shock or burns,
serious personal injury, or death.
· Before connecting your appliance to the power supply, verify the supply
voltage and circuit rating match the appliance. Correct improper supply
voltage or circuit size immediately.
· Before connecting your appliance to the power supply, verify the power
supply is correctly grounded. If the power supply is not grounded, correct
immediately. TRUE recommends hiring a qualified electrician to inspect your
wall outlet and circuit to ensure they are properly grounded.
· DO NOT clean appliance with a pressure washer or hose. DO NOT immerse power
cord in water.
· Powering off an electronic control or setting temperature controls to 0 (off
position) does not remove power from all components. Unplug the appliance or
turn off the power supply before installation or servicing.
· The appliance should receive power from its own individual dedicated
electrical circuit. This provides the best performance and prevents
overloading the power supply.
· The original equipment manufacturer (OEM) power cord has a grounding plug to
minimize the possibility of electrical shock.
· Never remove the ground prong from the power cord! For personal safety, this
appliance must be properly grounded.
· Never use an extension cord! An extension cord is any component that adds
length to the OEM power cord when connecting the cord to a power source.
· Never use an adapter plug! An adapter plug alters the OEM plug configuration
when connecting the plug to a power source.
· Never use a power cord that shows cracks or abrasion damage along its length
or at either end.
· Immediately have a qualified technician replace damaged OEM power cords with
OEM components.
· Never unplug your appliance by pulling on the power cord. Always grip the
plug and pull the plug straight out of the outlet.
· Take care to prevent rolling over or damaging the power cord when moving the
appliance.
· Never use the power cord to prevent appliance movement. Always use adequate
means to keep the appliance in place without transmitting stress to the power
cord.
· Keep power cord away from heated surfaces.
· DO NOT let power cord hang over edge of table or counter.
· DO NOT excessively bend or place heavy articles on the power cord.
NOTICE!
TRUE will not warranty the following: · Compressor failures due to improper
incoming voltage. · Appliance with tampered OEM power cords. · Appliance
connected to adapters or extension cords.
For more details, see TRUE’s full warranty statement.
TEC_TM_043 | REV. G | EN
01/23/2024
Page 7 of 56
TBR/TDR
About Your Appliance & Installation Requirements
About Your Appliance & Installation Requirements
USER ACTION!
TRUE is not responsible for damage incurred during shipment. Always carefully
inspect for freight damage before receiving and installing your appliance. If
there is damage, note all damage on the delivery receipt, immediately file a
claim with the delivery freight carrier, and contact TRUE. Do not install the
appliance or put it in service.
Thank you for choosing TRUE Manufacturing to meet your refrigeration needs.
TRUE highly recommends a qualified technician and electrician install your
appliance to ensure correct installation. The cost of professional
installation is money well spent. Only qualified technicians should install
and service the appliance.
For assistance finding a qualified technician, please visit our Service
Company Locator at truemfg.com/support/service-locator. TRUE is solely the
appliance manufacturer and is not responsible for installation.
The appliance owner is responsible for proper installation and maintaining the
appliance as described in this document. Routine care and maintenance
procedures are not covered by TRUE’s warranty.
Appliance Specifications
Some things to know about your appliance are as follows:
· Appliance tested for IEC to ISO Climate Class 5 [104°F (40°C) temperature,
40% relative humidity].
· For proper operation, ambient temperatures shall not be less than 60°F
(15.5°C) and no greater than 104°F (40°C).
· Appliance is not for the storage and/or display of potentially hazardous
foods when the temperature control is set above 41°F (5°C).
· Appliance is not suitable for outdoor use, unless otherwise stated on the
serial label.
· Appliance is not suitable for an area where a pressure washer or hose may be
used.
· Always plug the appliance into its own individual dedicated electrical
circuit!
· DO NOT use extension cords or adapter plugs.
· Before connecting your appliance to the power supply, verify the incoming
voltage (±5%) and the amps match the operation ratings on the appliance’s
serial label. Correct improper incoming voltage or amps immediately. Serial
label location varies by model.
· Before connecting your appliance to the power supply, verify the power
supply is correctly grounded. If the power supply is not grounded, correct
immediately.
· Ensure the installation location will provide adequate clearances and
sufficient airflow for the appliance. See “Clearances” (pg. 9).
· Read and follow all warnings and maintenance instructions. Failure to do so
may result in damage and void the warranty on your appliance.
Page 8 of 56
01/23/2024
P#803294
TEC_TM_043 | REV. G | EN
TBR/TDR
About Your Appliance & Installation Requirements (cont.)
Clearances
NOTICE!
Warranty is void if ventilation is insufficient. Be sure your appliance has
the required surrounding clearances for ventilation purposes. Keep all
ventilation openings in the appliance enclosure or structure housing the
appliance clear of obstruction.
MODEL TBR/TDR
TOP 0″ (0 mm)
SIDES 0″ (0 mm)
BACK 0″ (0 mm)
truemfg.com
TEC_TM_043 | REV. G | EN
01/23/2024
Page 9 of 56
TBR/TDR
About Your Appliance & Installation Requirements (cont.)
truemfg.com
Electrical Requirements
USER ACTION!
Find a copy of the wiring diagram with our serial number lookup at
truemfg.com/support/serial-number-lookup.
Electrical Installation & Safety
NEMA Plug Configurations 60 HZ USE ONLY!
TRUE uses these types of NEMA plugs shown. If you DO NOT have the proper
outlet, have a licensed electrician verify and install the correct power
source.
115 Volts
AMPS 2 3 4 5 6 7 8 9 10 12 14 16 18 20 25 30
Wire gauge chart (115V)
Distance in Feet to Center of Load
230 Volts
AMPS 5 6 7 8 9 10 12 14 16 18 20 25 30
Wire gauge chart (230V)
Distance in Feet to Center of Load
International (IEC) Plugs Only International appliances may be supplied with a
power cord that will require installation. Install this cord before connecting
the appliance to a power source.
NOTICE > International plug configurations will vary by country and voltage.
Installation Fully seat the power cord into the appliance receptacle until it
locks in position. See fig. 1.
Removal Depress the red button. See fig. 2.
Fig. 1. Fully insert the power cord into the receptacle.
Fig. 2. Push the red button to remove the plug.
Page 10 of 56
01/23/2024
P#803294
TEC_TM_043 | REV. G | EN
NOTES
TBR/TDR
truemfg.com
TEC_TM_043 | REV. G | EN
01/23/2024
Page 11 of 56
Installation & Setup
TBR/TDR
Installation & Setup
truemfg.com
WARNING!
The appliance owner is responsible for performing a Personal Protective
Equipment (PPE) hazard Assessment and to ensure adequate protection during
maintenance and cleaning procedures.
Use appropriate tools, safety equipment, and PPE during installation and
servicing.
Sharp edges! Take care when moving, installing, cleaning, servicing and
maintaining the appliance to avoid cuts. Be sure to take care when reaching
under the appliance or handling metal components. Keep fingers out of pinch
point areas, such as the space between appliance doors and surrounding
appliances. Take care closing doors with children nearby.
Risk of electrical shock or burn! Powering off an electronic control or
setting temperature controls to the 0 (off) position does not remove power
from all components. Unplug the appliance or turn off the power supply before
installation or servicing.
Tip over hazard! Appliance may pose a tipping hazard when uncrating,
installing or moving the appliance. Take appropriate safety precautions. Use
of tip over restraints may only reduce (not eliminate) the tipping hazard.
Never allow children to climb or hang on drawers, doors or shelves.
Uncrating
USER ACTION!
· If the appliance is damaged, note all damage on the delivery receipt,
immediately file a claim with he delivery freight carrier, and contact TRUE.
DO NOT install the appliance or put it in service.
· If the appliance is laid on its back or side, be sure to leave the appliance
upright twice the time it has been laying down (up to four (4) hours) before
plugging the appliance into a power source. If this time exceeds four (4)
hours, let the appliance sit upright for 24 hours before powering the
appliance.
NOTICE!
Keys for appliances with door locks are located in the warranty packet.
Required Tools Required tools include (but may not be limited to) the
following:
· Adjustable wrench
· Phillips screwdriver
Crush or cut hazard! Keep clear when uncrating, installing, moving, or servicing the appliance.
Page 12 of 56
01/23/2024
P#803294
TEC_TM_043 | REV. G | EN
TBR/TDR
Installation & Setup (cont.)
Procedure
1. Remove the outer packaging (cardboard and bubbles or styrofoam corners and
clear plastic). See fig. 1. Inspect for concealed damage. Again, immediately
file a claim with the freight carrier if there is damage. NOTICE > Move the
unit as close as possible to the final location before removing the wooden
skid.
2. With an adjustable wrench, remove all shipping bolts securing the wood
skid to the bottom of the cabinet. See fig. 2. NOTICE > Some models may
require removing the front and/or rear grill to access the shipping bolts.
3. If leveling legs or castors will not be used, remove the cabinet from the
wood skid and set the skid aside. NOTICE > DO NOT lift the cabinet by the
countertops, doors, drawers, or grills. If leveling legs or castors will be
used, rotate the cabinet on the skid (see fig. 3) and see the installation
instructions on the next page.
Fig. 1. Remove the exterior packaging.
Fig. 2. Shipping bolt locations.
TEC_TM_043 | REV. G | EN
Fig. 3. When lifting unit, do not use countertops, doors/ drawers, or grills as a lifting point.
01/23/2024
Page 13 of 56
Installation & Setup (cont.)
TBR/TDR
truemfg.com
Appliance Location
· Ensure that the drain hose or hoses are positioned in the pan.
· Free the plug and cord from inside the lower rear of the appliance (DO NOT
plug in).
· Place the appliance close enough to the electrical supply so that extension
cords are never used.
Leveling Screw, Leg, or Castor Installation
Procedure Leveling Screws
If leveling screws are not factory installed, then, with access to the
appliance bottom, install the leveling screws into the threaded holes in the
frame rail or appliance bottom. See figs. 13.
WARNING!
Fig. 1. Leveling screw.
Tipping hazard! ALWAYS verify center leveling screws fully contact the floor after leveling the appliance.
Leveling screws are provided to assist with leveling the appliance. Adjustable
legs provide 6″ (152 mm) of clearance under the appliance. Castors provide
appliance mobility.
Required Tools Required tools include (but may not be limited to) the
following:
· Adjustable Wrench
Fig. 2. Turn the leveling screws clockwise to lower the appliance.
Fig. 3. Turn the leveling screws counterclockwise to raise the appliance.
Page 14 of 56
01/23/2024
P#803294
TEC_TM_043 | REV. G | EN
Installation & Setup (cont.)
TBR/TDR
truemfg.com
Procedure 6″ (152 mm) Leveling Legs
1. Access the appliance bottom. 2. If present, remove the leveling screws. 3.
Thread the leveling legs into the frame rail or appliance
bottom. See figs. 4 and 5. 4. Verify that the appliance is level. See “Level
the Appliance”
(pg. 16). 5. If the appliance is not level, gently lift and support the low
end
of the appliance. Then, with an adjustable wrench, screw the leveling leg
bottom stems in or out to level and support the appliance. See fig. 4 and 6.
Lower Rail Assembly
Rail End
Snug Fit Here
Fig. 4. Leveling leg diagram.
Bottom Stem
Procedure — Castors
USER ACTION!
Install castors with brakes in the front.
1. Access the appliance bottom. 2. If present, remove the leveling screws. 3.
Thread the castors into the frame rail or appliance bottom.
See figs. 7 and 8. 4. Verify the appliance is level. See “Level the Appliance”
(pg. 16). 5. On the low end of the appliance, loosen the castor bolt
enough to slide provided castor shims between the castor bearing and the
bottom rail of the appliance. See fig. 9. 6. Install the desired number of
shims. See fig. 9. · If more than one shim is used, be sure shim slots are
offset. See fig. 10. · DO NOT use more than four (4) shims on a castor. · Be
sure each shim touches the castor stem. 7. Tighten and secure the shims and
castors. 8. Verify the appliance is level. 9. If the appliance is not level,
repeat the steps 3 6 until the appliance is level and supported.
Fig. 5. Screw the leveling legs into the threaded holes.
Rail End Snug Fit Here Bearing Race
Castor
Lower Rail Assembly Castor Stem
Leveling Shim
Fig. 7. Castor diagram.
Fig. 8. Screw the castors into the threaded holes.
Fig. 6. Turn the bottom stem to level the appliance. TEC_TM_043 | REV. G | EN
Fig. 9. Insert the castor shim(s). be sure Fig. 10. Install multiple shims with offset
to tighten the castor stem.
slots.
01/23/2024
Page 15 of 56
Installation & Setup (cont.)
TBR/TDR
Level the Appliance
Seal the Appliance to the Floor
WARNING!
Tipping hazard! ALWAYS verify center leveling screws fully contact the floor
after leveling the appliance.
USER ACTION!
Asphalt floors are susceptible to chemicals. TRUE recommends installing a
layer of tape between the asphalt and the sealant to protect the floor.
Proper leveling of your TRUE appliance is critical to operating success (for
non-mobile appliances). Leveling impacts effective condensate removal and door
operation. See “Leveling Screw, Leg or Castor Installation” (pg. 14) for level
adjustment and shimming information. Procedure Position the appliance in its
final installation location. Then, level the appliance front-to-back and side-
to-side. See fig. 1. 1. Position the level on the inside floor of the
appliance near the
doors (level parallel to appliance front). Level the appliance. 2. Position
the level at the inside rear of the appliance (level
parallel to appliance back). Level the appliance. 3. Position the level on the
left and right inside floor (level parallel
to appliance sides). Level the appliance.
Fig. 1. Measure the level along the perimeter of the interior floor.
The following procedure describes sealing a non-mobile appliance to the floor
for NSF standards. This may not be required for your application. Procedure 1.
Position the appliance in its final installation location. Be sure
to leave adequate clearance between the back and sides per “Clearances” (pg.
9) to ensure proper ventilation.
2. Level the appliance front-to-back and side-to-side. See “Level the
Appliance” (pg. 16).
3. Draw an outline of the appliance base on the floor.
4. Raise and block the front side of the appliance.
5. Apply a bead of NSF-approved sealant (see list below) to the floor, 1/2″
(13 mm) inside the front part of the outline drawn in step 3. The bead of
sealant must be heavy enough to seal the entire appliance surface when the
appliance is lowered on top of the sealant.
6. Raise and block the rear of the appliance.
7. Apply sealant to the floor on the other three sides, as outlined in step
5.
8. Examine the appliance to ensure that it is sealed to the floor around the
entire perimeter.
NSF-Approved Sealants · 3M #ECU800 Caulk
· 3M #ECU2185 Caulk
· 3M #ECU1055 Bead
· 3M #ECU1202 Bead
· Armstrong Cork Rubber Caulk
· Products Research Co. #5000 Rubber Caulk
· G.E. Silicone Sealer
· Dow Corning Silicone Sealer
Page 16 of 56
01/23/2024
P#803294
TEC_TM_043 | REV. G | EN
Installation & Setup (cont.)
TBR/TDR
Shelf Installation
WARNING!
Overloading, incorrectly installing, or improperly loading shelves can cause
shelf failure and negatively affect appliance operation, resulting in
appliance damage, product damage, or personal injury.
DO NOT use pliers or any crimping tools when installing shelf clips. Altering
shelf clips in any way can lead to shelving instability.
Fig. 1. Installing top tab of shelf clip.
Fig. 2. The bottom tab of the shelf clip will fit tightly.
Installation Tips · Install all the shelf clips before installing any shelves.
· Start at the bottom shelf and work your way up.
· Always lay the back of each shelf down on the rear clips before the front.
Procedure 1. Hook the shelf clips into the shelf standards. See fig. 1.
2. Push up on the bottom of the clip. See fig. 2. NOTICE > You may need to
squeeze or twist the bottom of
the shelf clip for proper installation. Position all four shelf clips equal in
distance from the floor for flat shelves. 3. Ensure the shelf clip is not
loose or able to wiggle out of the shelf standard. See figs. 3 and 4.
4. Place the shelves on the shelf clips with the cross support bars facing
down. NOTICE > Be sure all shelf corners are properly seated.
Shelf Adjustment Shelving is adjustable for customer application. This
appliance meets the IEC Shelf Weight Capacity of 47lb/ft2 (230kg/m2).
Fig. 3. You may need to squeeze or twist Fig. 4. Installed shelf clip. the bottom of the shelf clip to install.
Shelf Standards
Shelf
Shelf
Shelf Clip
Pillaster (I-beam)
TEC_TM_043 | REV. G | EN
01/23/2024
Page 17 of 56
TBR/TDR
Installation & Setup (cont.)
Draft Tower Installation
Procedure 1. Position the rubber washer (see fig. 1) over the mounting holes
in the cabinet countertop.
2. Thread the beer line connector (see fig. 2) to the draft arm. See fig. 3.
3. Run the beer line through the hole and into the cabinet. See fig. 4.
4. With the provided hardware, install the draft arm. See figs. 5 and 6.
5. Remove the top of the draft arm. See fig. 7a.
6. Insert the air hose [1″ (25.4mm) plastic tube] into the draft arm. See
fig. 7b. NOTICE > Take care to not disturb the insulation.
7. Hook the air hose clip to the insulating sleeve at the top of the draft
arm. See fig. 8. NOTICE > The clip ensures the chill hose, which keeps the
beer faucet cold, remains correctly positioned.
8. Replace the top of the draft arm.
Fig. 1. Draft arm components; draft arm not shown.
truemfg.com
Fig. 2. Be sure to insert the O-ring into the beer line connector.
Fig. 3. Attach the beer line connector to the draft arm.
Fig. 4. Run the line into the cabinet.
Fig. 5. Ensure the rubber gasket is between the countertop and draft arm.
Fig. 6. Thread the handle onto the beer draft arm.
A
B
Fig. 7. Route the air hose through the draft tower from below.
Fig. 8. Hang the chill hose clip over the beer line. Page 18 of 56
01/23/2024
P#803294
TEC_TM_043 | REV. G | EN
Installation & Setup (cont.)
TBR/TDR
Parts Key
A Spill Tray Grate
B Spill Tray
C Tray Gasket
A
D Spill Tray Access Port
B
Draft Spill Tray
Procedure 1. Place the tray gasket over the spill tray tube.
2. Slide the spill tray tube into the spill tray access port.
3. Carefully position the spill tray on the countertop.
4. From the inside of the cabinet, thread the spill tray tube nut onto the
tube securing the spill tray to the countertop. See figs. 13. NOTICE > Hand
tighten only.
5. Place the spill tray grate into the spill tray.
6. Place a 3/4″ (19 mm) i.d. hose onto the spill tray tube.
7. With the draft spill tray positioned and secured, apply a bead of RTV
Silicone (provided) to seal the spill tray to the countertop. See fig. 4.
C D
Fig. 1. Spill tray tube nut installation location.
truemfg.com
Fig. 2. Thread the spill tray tube nut.
Fig. 3. Hand-tighten only.
TEC_TM_043 | REV. G | EN
Fig. 4. Apply silicone around the spill tray. 01/23/2024
Page 19 of 56
TBR/TDR
Installation & Setup (cont.)
Air Distributor Manifold & Distributor Cover
A 2-way air distributor manifold is included to allow a single CO supply line
to pressurize two kegs. The air distributor is located behind the distributor
cover. To access, lift the cover off the manifold mounting bracket. See figs.
1 and 2.
CO & Keg Connections
WARNING!
Contents under pressure. Take care when handling filled CO tanks. If
unfamiliar with using CO tanks and/or regulators, seek information from your
local distributor or brewer representative before proceeding.
Fig. 1. LIft the distributor cover. Fig. 2. The 2-way distributor manifold.
NOTICE > CO2 cylinders, regulators, and keg tappers are not provided by TRUE.
Required Tools Required tools include (but may not be limited to) the
following:
· CO2 Cylinder
· Pressure Regulator
· Tapper NOTICE > Be sure to use hose clamps for all air and beer
lines as applicable. Procedure 1. Attach a pressure regulator to your CO2
cylinder.
2. Connect the pressure regulator to the distributor manifold.
3. Connect the distributor manifold to your tapper(s).
4. Connect the draft tower beer line(s) to your tapper(s).
5. Attach the tapper(s) to your keg(s).
6. Open the pressure regulator valve and pressurize the system. NOTICE > It
requires 1/2 lb (0.23 kg) of CO2 to dispense
a half-barrel of beer at 38°F (3.3°C) with 15 psi (1.03 bar) of pressure on
the barrel. 7. Engage your tapper(s)
8. Check all connection points for leaks. If the system leaks, verify all
fittings and clamps are tight and seal correctly.
Page 20 of 56
01/23/2024
P#803294
TEC_TM_043 | REV. G | EN
TBR/TDR
truemfg.com
Installation & Setup (cont.)
Beer Drain Bottle & Hanger
An optional beer drain bottle and hanger may be purchased to collect the
overflow from the draft spill tray. The bottle hanger slides over the top of
the beer keg. See fig. 1.
Route a 3/4″ (19 mm) I.D. vinyl hose from the spill tray tube into the drain
bottle. Empty the bottle as determined by usage.
Access Ports
Access ports provide optional locations to route external beer lines, CO
lines, or overflow beer spill tray drain lines.
Carefully drill through the access port’s inner and outer sleeves. Once the
lines have been routed, seal around the line with food grade silicone.
Standard small-floor opposite evaporator cover.
Fig. 1. Drain bottle and hanger on keg.
Standard large-floor next to evaporator cover.
Standard small-side wall opposite evaporator cover.
TEC_TM_043 | REV. G | EN
01/23/2024
Page 21 of 56
TBR/TDR
Installation & Setup (cont.)
Access Ports (cont.)
DRILL ZONES No drilling allowed on any face with doors!
Access ports are available for purchase to plug drilled holes.
Applies to all sizes. 3-door model shown.
NO DRILLING ALLOWED
Mirror dimensions for right-hand cooling systems
truemfg.com
CONDENSING UNIT SIDE VIEW
NON-CONDENSING UNIT SIDE VIEW
Page 22 of 56
01/23/2024
P#803294
TEC_TM_043 | REV. G | EN
TBR/TDR
Installation & Setup (cont.)
Overlay Panel Specifications
For panel installation instructions, see “Overlay Panel Installation” on (pg. 27).
Slotted Grill
FRONT
3/4″ 19mm
31/32″ 24mm
11 19/32″ 294mm
9 11/16″ 246mm
2X 1 23/32″ 44mm
3/4″ 19mm
16 1/4″ 413mm
31 11/16″ 805mm
1 5/8″ 41mm
14X 3/4″ 19mm
12X 1 9/16″ 40mm
05/24/22
31/32″ 24mm
BACK
11 19/32″ 294mm
9 11/16″ 246mm
31 11/16″ 805mm
2X 1 23/32″ 44mm
14X 3/4″ 19mm
12X 1 9/16″ 40mm
Grill with Holes
3/4″ 19mm
4 5/32″ 105mm
3 5/16″ 84mm
31/32″ 24mm
FRONT
11 19/32″ 294mm
9 11/16″ 246mm
2X 1 23/32″ 44mm
3/4″ 19mm
31/32″ 24mm
05/24/22
BACK
11 19/32″ 294mm
9 11/16″ 246mm
2X 1 23/32″ 44mm
16 1/4″ 413mm
31 11/16″ 805mm
1 5/8″ 41mm
2X 10 1/8″ 257mm
31 11/16″ 805mm
2X 10 1/8″ 257mm
TEC_TM_043 | REV. G | EN
4 5/32″ 105mm
3 5/16″ 84mm
01/23/2024
Page 23 of 56
TBR/TDR
truemfg.com
Installation & Setup (cont.)
Overlay Panel Specifications (cont.)
For panel installation instructions, see “Overlay Panel Installation” on (pg. 27).
TBR | TDR48
Glass Door Panel Specifications
Width
17-5/8″ (448 mm)
Height
31-11/16″ (805 mm)
Depth
3/4″ (19 mm)
Weight
15 lb (6.8 kg) max
Rail Style Dimension
2″ (50.8 mm) max
Viewable Area Height
25-11/16″ (652 mm)
Viewable Area Width
11-5/8″ (295 mm)
Solid Door Panel Specifications
Width
17-5/8″ (448 mm)
Height
31-11/16″ (805 mm)
Depth
3/4″ (19 mm)
Weight
15 lb (6.8 kg) max
Rail Style Dimension
2″ (50.8 mm) max
GLASS DOOR
3/4″ 19mm
9/32″ 7mm
11/32″ 9mm
3/8″ 10mm X 1 1/8″ 29mm 3/4″ 19mm
8 13/16″ 224mm
11 5/8″ 295mm
3/8″ 10mm
11/32″ 9mm
3/4″ 19mm
SOLID DOOR
05/24/22
9/32″ 7mm
3/8″ 10mm X 1 1/8″ 29mm 3/4″ 19mm
8 13/16″ 224mm
3/8″ 10mm
31 11/16″ 805mm
25 11/16″ 652mm
31 11/16″ 805mm
17 5/8″ 448mm
17 5/8″ 448mm
Page 24 of 56
01/23/2024
P#803294
TEC_TM_043 | REV. G | EN
TBR/TDR
truemfg.com
Installation & Setup (cont.)
Overlay Panel Specifications (cont.)
For panel installation instructions, see “Overlay Panel Installation” on (pg. 27).
TBR | TDR32/52/72/92
Glass Door Panel Specifications
Width
19-5/8″ (498 mm)
Height
31-11/16″ (805 mm)
Depth
3/4″ (19 mm)
Weight
15 lb (6.8 kg) max
Rail Style Dimension
2″ (50.8 mm) max
Viewable Area Height
25-11/16″ (652 mm)
Viewable Area Width
13-5/8″ (346 mm)
Solid Door Panel Specifications
Width
19-5/8″ (498 mm)
Height
31-11/16″ (805 mm)
Depth
3/4″ (19 mm)
Weight
15 lb (6.8 kg) max
Rail Style Dimension
2″ (50.8 mm) max
GLASS DOOR
3/4″ 19mm
9/32″ 7mm
11/32″ 9mm
3/8″ 10mm X 1 1/8″ 29mm 3/4″ 19mm
9 13/16″ 249mm
13 5/8″ 346mm
3/8″ 10mm
11/32″ 9mm
3/4″ 19mm
SOLID DOOR
05/24/22
9/32″ 7mm
3/8″ 10mm X 1 1/8″ 29mm 3/4″ 19mm
9 13/16″ 249mm
3/8″ 10mm
31 11/16″ 805mm
25 11/16″ 652mm
31 11/16″ 805mm
19 5/8″ 498mm
19 5/8″ 498mm
TEC_TM_043 | REV. G | EN
01/23/2024
Page 25 of 56
TBR/TDR
Installation & Setup (cont.)
Overlay Panel Specifications (cont.)
For panel installation instructions, see “Overlay Panel Installation” on (pg.
27).
TBR | TDR36/60/84/108
Glass Door Panel Specifications
Width
23-5/8″ (600 mm)
Height
31-11/16″ (805 mm)
Depth
3/4″ (19 mm)
Weight
15 lb (6.8 kg) max
Rail Style Dimension
2″ (50.8 mm) max
Viewable Area Height
25-11/16″ (652 mm)
Viewable Area Width
17-5/8″ (448 mm)
Solid Door Panel Specifications
Width
23-5/8″ (600 mm)
Height
31-11/16″ (805 mm)
Depth
3/4″ (19 mm)
Weight
15 lb (6.8 kg) max
Rail Style Dimension
2″ (50.8 mm) max
3/4″ 19mm
9/32″ 7mm
GLASS DOOR
11/32″ 9mm
3/8″ 10mm X 1 1/8″ 29mm 3/4″ 19mm
11 13/16″ 300mm
3/8″ 10mm
17 5/8″ 448mm
11/32″ 9mm
3/4″ 19mm
SOLID DOOR
05/24/22
9/32″ 7mm
5/16″ 8mm X 1 1/8″ 29mm 3/4″ 19mm
11 13/16″ 300mm
13/32″ 10mm
31 11/16″ 805mm
25 11/16″ 652mm
31 11/16″ 805mm
23 5/8″ 600mm
23 5/8″ 600mm
Page 26 of 56
01/23/2024
P#803294
TEC_TM_043 | REV. G | EN
TBR/TDR
truemfg.com
Installation & Setup (cont.)
Overlay Panel Installation
NOTICE!
Take care to not damage the panel finish!
This instruction demonstrates using cardboard from the unit’s exterior
packaging for surface protection.
Recommended panel thickness is 3/4″ (19.05 mm).
Required Tool(s) · Surface Protection* · Phillips Screwdriver · 2+ Clamps [2″ (50.8 mm)] · 5/16″ Socketwrench · 5/8″ (15.8751 mm) Screws** · Tape Measure
· Marking Utensil · Tape · 3/8″ Drill Bit · 17/64″ Drill Bit · Drill
*Cardboard, moving blanket, foam padding, etc.
**Required quantities vary by application. Be sure the screws are shorter than
the panel thickness.
Grill Overlay Installation Procedure
1. Carefully lay the grill overlay panel facedown on a protected surface.
2. With a Phillips screwdriver, remove the cabinet grill. See fig. 1.
3. Place the grill facedown on the overlay panel. Then, center the grill and
overlay. See fig. 2. NOTICE > Center the cabinet grill and overlay panel at
the corners.
4. Clamp the grill and overlay. See fig. 2. NOTICE > If the clamp jaws are
not padded, insert padding
between the clamp and the overlay to protect the panel’s finish.
5. Fasten the overlay to the grill. See fig. 3. NOTICE > Be sure the mounting
screws are shorter than the
overlay panel thickness.
6. Remove the clamps, and then reinstall the grill.
Glass & Solid Door Overlay Installation
Procedure 1. Carefully lay the door overlay panel facedown on a protected
surface.
2. With a 5/16″ socketwrench, remove the cabinet door. See fig. 4.
3. Remove the door gasket, top hinge pin & bushing (fig. 5a), and door cam
riser (fig. 5b).
4. Place the door facedown on the overlay. Then, center the door and overlay.
See fig. 6. NOTICE > Center the door and overlay panel at the corners.
Fig. 1. Pull the top of the cover forward and then lift.
Fig. 2. Center the overlay and grill at the corners. The panel is slightly larger than the grill.
Fig. 3. Cabinet grill predrilled hole locations.
Fig. 4. Carefully remove the door from the unit.
A
B
Fig. 5. Remove the top hinge pin & bushing (A) and the door cam riser (B) from the hinge brackets. Do not remove the hinge brackets.
TEC_TM_043 | REV. G | EN
01/23/2024
Page 27 of 56
TBR/TDR
Installation & Setup (cont.)
Overlay Panel Installation (cont.)
Procedure (cont.) 5. Clamp the door and panel. See fig. 6. NOTICE > If the
clamp jaws are not padded, insert padding between the clamp and the overlay to
protect the panel’s finish. 6. Fasten the overlay to the door (see fig. 7).
Then, remove the clamps. NOTICE > Be sure the mounting screws are shorter than
the panel width. 7. Mark the drill bits with the measures below. See fig. 8.
a. 3/8″ bit at 1/2″ (25.4 mm)
b. 17/64″ bit at 1-1/8″ (28.575 mm)
8. Carefully drill holes for both hinges as described below. See fig. 9.
a. Drill the 3/8″ hinge bushing/cam hole.
b. At the center of the bushing hole, drill the 17/64″ hinge pin hole. NOTICE
Drill the hinge pin hole until the mark reaches
the hinge bracket, not the bottom of the bushing hole. See fig. 9. 9. With the existing hardware, install the door handle(s). See figs. 10 and 11.
10. Install the hinge components.
11. Install the gasket. NOTICE > Verify the gasket is fully seated in the gasket
channel. See fig. 12.
NOTICE!
Be sure to drill straight down to prevent cracking the overlay and/or drilling through the side.
12. Install the door assembly. Verify the door closes correctly and the gasket seals without gaps. Repeat the process for each door.
Fig. 6. Be sure the overlay’s center slot is positioned at the top of the door.
Fig. 7. Cabinet door predrilled hole locations.
1/2″ (12.7 mm)
Bushing /Cam Hole
1-1/8″ (28.575 mm)
Pin Hole
Fig. 8. Mark the hole depths on the drill Fig. 9. Drill the 3/8″ hole first.
bits.
THEN drill the 17/64″ hole.
Page 28 of 56
01/23/2024
P#803294
TEC_TM_043 | REV. G | EN
Installation & Setup (cont.)
TBR/TDR
truemfg.com
Fig. 10. Handle screw locations.
Fig. 11. Installed door handles.
A
B
Fig. 12. Pull the side of the gasket to check its installation. A: CORRECT; gasket channel is NOT visible. B: INCORRECT; gasket channel is visible.
TEC_TM_043 | REV. G | EN
01/23/2024
Page 29 of 56
Appliance Operation
TBR/TDR
Appliance Operation
truemfg.com
WARNING SPOILAGE!
The owner is solely responsible for ensuring safe holding temperature levels
for all food items. Failure to do so may result in unsafe food products. Loss
or spoilage of products in your appliance is not covered by warranty. In
addition to following recommended installation procedures, run the appliance
for 24 hours prior to usage to verify operation.
Startup
USER ACTION!
Before loading product, run your TRUE appliance empty for 24 hours to verify
proper operation. Remember, our factory warranty DOES NOT cover product loss!
· The compressor is ready to operate when the appliance is purchased. All you
need to do is plug in the appliance.
· Good air flow inside your TRUE appliance is critical. Take care to prevent
product from pressing against the sides or back wall and coming within 4″
(101.6 mm) of the evaporator housing. Refrigerated air off the evaporator coil
must circulate throughout the appliance for even product temperatures.
· Excessive tampering with the control could lead to service difficulties. If
replacing the temperature control is ever needed, be sure to order the
replacement from your TRUE dealer or recommended service agent.
· All covers and access panels must be in place and properly secured before
operating this appliance.
Page 30 of 56
01/23/2024
P#803294
TEC_TM_043 | REV. G | EN
TBR/TDR
Appliance Operation (cont.)
Temperature Control & Light Switch Location
The light symbol switch.
shows the approximate location of the light
Factory Installed TruLumina LED To change the display color of the TruLumina
LEDs, toggle the light switch off and then on. Repeat to cycle trough all
available colors. Leaving the light switch in the “off” position for two
seconds will turn off the lights.
Light Switch on Glass Door Models
Inside the top ceiling.
truemfg.com
Electronic Temperature Control
On the front of grill.
ECO
°C
°F
TEC_TM_043 | REV. G | EN
01/23/2024
Page 31 of 56
Appliance Operation (cont.)
TBR/TDR
truemfg.com
General Sequence of Operation — Refrigerator and Freezer Appliances
USER ACTION!
For more information regarding a appliance’s temperature control adjustment or
general sequence of operation, please see our Temperature Control
Adjustment–Sequence of Operation Manual in our resource library at truemfg.com
/service-manuals/sequence-of-operation or scan the QR code.
When the appliance is plugged in:
· Interior lights will illuminate on glass door models (see Temperature
Control & Light Switch Location, pg. 33).
· An electronic control with digital display will illuminate (if installed).
· There may be a short delay before the compressor and/or evaporator fan(s)
start. This delay may be determined by time or by temperature, which could be
the result of an initial defrost event that will last at least 6 minutes.
· The temperature control/thermostat may cycle the compressor and evaporator
fan(s) on and off together. Every appliance will require a defrost event to
ensure the evaporator coil remains clear of frost and ice buildup. Defrost is
initiated by a defrost timer or by the electronic control. EXCEPTION Models
TSID, TDBD, TCGG, and TMW do not have an evaporator fan(s). · The temperature
control/thermostat senses either an evaporator coil temperature or air
temperature, NOT product temperature.
· An analog thermometer, digital thermometer, or electronic control display
may reflect the refrigeration cycle swings of up and down temperatures, NOT
product temperature. The most accurate method to determine a appliance’s
operation is to verify the product temperature.
· Refrigerators with mechanical temperature controls will defrost during every
compressor off-cycle.
· Freezers with mechanical temperature controls will defrost by time
initiation as determined by a defrost timer. EXCEPTION Models TFM, TDC, THDC
and TMW require a manual defrost. The frequency of this manual defrost will
depend on the appliance’s usage and ambient conditions.
· An electronic control with a digital display (if installed) will show dEF
during defrost. NOTICE > The display may have a short delay before showing a
temperature after a defrost event has expired and instead
show dEF during a refrigeration cycle. · Models with an analog or digital
thermometer may show higher than normal temperatures during defrost.
· A refrigerator will use the evaporator fans to clear the coil during
defrost. EXCEPTION Models TSID, TDBD, and TCGG do not have an evaporator
fan(s).
· A freezer will use heaters to clear the evaporator coil during defrost.
NOTICE > The evaporator coil heater and drain tube heater are only energized
during defrost. Defrost is terminated when a
specific evaporator coil temperature is reached or by a time duration.
Page 32 of 56
01/23/2024
P#803294
TEC_TM_043 | REV. G | EN
TBR/TDR
Appliance Operation (cont.)
Draft Beer Storage, Handling & Operation
DRAFT BEER SHOULD BE TREATED AS A FOOD PRODUCT.
In most instances draft beer is not pasteurized. It is very important that you
store and handle it properly.
Follow these steps to ensure the highest quality and consumer satisfaction.
· Immediately store draft beer in a refrigerated cabinet.
· Draft beer products have a recommended shelf life. If you have questions
regarding the shelf life of any of your draft products, please consult with
your supplying depot or respective brewer representative.
· Store kegs separately from food products. If your cooler is used to
refrigerate draft and food products, DO NOT store food near or on the kegs.
· Keep keg storage and dispensing areas clean to prevent any possibility of
contaminating your draft products.
Temperature Correct temperature is a key factor in storing and dispensing
draft beer. Beer that is too cool or too warm may be subject to flavor loss,
off taste and dispensing problems.
Helpful Hints for Controlling Temperature · Keep a thermometer handy.
· Monitor the draft temperature in the cooler and at the tap.
· Keep cooler door closed as much as possible to avoid temperature
fluctuation.
· Regular maintenance of refrigeration equipment is recommended.
Pressure Dispensing pressures differ based on the following:
· Draft dispensing line length.
· Draft dispensing system type.
· Actual product (pressure requirements vary).
· Product temperature.
· Pressurizing agent: Air pressure, CO or special blended gases.
Helpful Hints on Maintaining the Correct Pressure · Know which pressurizing
agent to use on which product, and why.
· Monitor your regulators to ensure applied pressure remains constant.
· Keep equipment in good repair.
Tapping DO NOT agitate the kegs unnecessarily. If excessive agitation occurs,
allow kegs to settle 1 to 2 hours before tapping.
Prior to tapping the keg, ensure all beer faucets in the serving location are
in the off position. Completely remove the dust cover (identification cap)
from the keg.
TEC_TM_043 | REV. G | EN
01/23/2024
Page 33 of 56
TBR/TDR
Appliance Operation (cont.)
Changing CO Gas Cylinder
Pressure Adjustment on CO Regulator
WARNING!
Contents under pressure. Take care when handling filled CO tanks. If
unfamiliar with using CO tanks and/or regulators, seek information from your
local distributor or brewer representative before proceeding.
WARNING!
Contents under pressure. Take care when handling filled CO tanks. If
unfamiliar with using CO tanks and/or regulators, seek information from your
local distributor or brewer representative before proceeding.
CAUTION!
Always follow these instructions when you replace a CO gas cylinder.
Procedure 1. Close cylinder valve A.
2. Remove tap head D from the barrel. Pull the pressure release ring on the
body of the tap to release pressure remaining in the line (DO NOT close
regulator shut-off C).
3. Remove or loosen regulator key B by turning counter clockwise.
4. Remove the regulator from used cylinder at outlet E.
5. Remove the dust cap from new gas cylinder at outlet E and clear dust from
the outlet by opening and closing valve A quickly using appropriate wrench.
6. Attach the regulator to the new cylinder at outlet E (use new
fiber/plastic washer, if required).
7. Completely open valve A.
8. Close valve C.
9. Adjust regulator key B by turning clockwise to set pressure. Check setting
by opening C and pulling and releasing the ring F on the pressure release
valve on the body of the tap.
10. Tap the barrel at D with valve C open. NOTICE >
· DO NOT lay CO cylinders flat.
· DO NOT drop CO cylinders.
· It requires 1/2 lb. (0.23 kg) of CO to dispense a half-barrel of beer at
38°F (3.3°C) with 15 psi (1.03 bar) of pressure on the barrel.
Increasing Pressure — Procedure 1. Close regulator shut-off C. 2. Turn the
regulator key B clockwise and adjust setting. 3. Tap the gauge for an accurate
reading. 4. Open regulator shut-off C and draw beer. Decreasing Pressure —
Procedure 1. Close regulator shut-off C. 2. Untap the barrel at D and to bleed
line, activate the tap
handle. Leave it in the open position. 3. Slowly open regulator shut-off C and
simultaneously turn
regulator key B counter-clockwise to zero reading. 4. Close regulator shut-off
C and set pressure by turning regulator
key B clockwise. Check the setting by opening and closing valve C. 5. Close
the tap head D (put in OFF position). 6. Tap the barrel at D and open
regulator shut-off C.
Parts Key A Cylinder Valve B Regulator Key C Regulator Shut-off D Tap Head E
CO Cylinder Outlet F Ring
Page 34 of 56
01/23/2024
P#803294
TEC_TM_043 | REV. G | EN
NOTES
TBR/TDR
TEC_TM_043 | REV. G | EN
01/23/2024
Page 35 of 56
Maintenance & Servicing
TBR/TDR
Maintenance & Servicing
WARNING!
· Only qualified technicians should install and service the appliance. For
assistance finding a qualified technician, please visit our Service Company
Locator at
truemfg.com/support/servicelocator.
· Turn off and lockout all utilities (gas, electric, water) according to
approved practices during maintenance or servicing.
The appliance owner is responsible for performing a Personal Protective
Equipment (PPE) Hazard Assessment and ensuring adequate protection during
maintenance and cleaning procedures.
Use appropriate tools, safety equipment, and PPE during installation and
servicing.
Sharp Edges! · Take care when moving, installing, cleaning,
servicing, and maintaining the ice machine to avoid cuts. Be sure to take care
when reaching under the ice machine or handling metal components. · Stay clear
of pinch point areas, such as the space between appliance doors and
surrounding cabinetry. Take care closing doors with children nearby.
WARNING!
Risk of electric shock or burn! · Powering off an electronic control or
setting
temperature controls to the 0 (off) position DOES NOT remove power from all
components. Unplug the appliance or turn off the power supply before
installation or servicing. · DO NOT clean appliance with a pressure washer or
hose.
Flammable refrigerant/insulation used! Have a licensed service provider
service your appliance to minimize the risk of possible ignition due to
incorrect parts or improper service and to ensure the operator’s health and
safety.
Crush or cut hazard! Keep clear when uncrating, installing, moving, or
servicing the appliance.
Slippery Surfaces! Moisture from improper drainage can create slippery
surfaces near the appliance. It is your duty to immediately warn your
customers of, and dry, the slippery surface. All wet floor areas must be
marked with a wet floor sign.
Page 36 of 56
01/23/2024
P#803294
TEC_TM_043 | REV. G | EN
Maintenance & Servicing (cont.)
TBR/TDR
USER ACTION!
· For additional maintenance instruction, please visit the media center at
truemfg.com.
· Any appliance adjustments are to be made AFTER the appliance has been
verified level and properly supported.
NOTICE!
The appliance owner is responsible for maintaining the appliance as described
in the installation manual. Routine care and maintenance procedures are not
covered by TRUE’s warranty.
Component Replacement
· Replace components with original equipment manufacturer (OEM) components
such as those shown in fig. 1. OEM parts minimize the risk of possible
ignition due to incorrect parts. Use of non-OEM components may void TRUE’s
warranty.
· Have a licensed service provider service your appliance to minimize the risk
of possible ignition due to incorrect parts or improper service and to ensure
the operator’s health and safety.
Fig. 1. Example of OEM parts.
truemfg.com
TEC_TM_043 | REV. G | EN
01/23/2024
Page 37 of 56
Maintenance & Servicing (cont.)
TBR/TDR
Recommended Maintenance
See recommended maintenance tasks and frequencies below. Some tasks may be
required more frequently based on your installation.
Maintenance Tasks
Monthly Quarterly Annually
Verify the appliance maintains product temperature.
X
X
X
Inspect power cord for damage; if damaged, replace immediately.
X
X
X
Verify the power cord is fully plugged into the wall receptacle
X
Inspect the overall condition of the appliance and its components (such as castors, doors, and hinges).
X
X
X
Verify operation of all moving parts (such as fan motors, doors and door cords).
X
Check physical condition of all gaskets; verify gaskets seal correctly.
X
X
Inspect any lamps, lamp holder connections, LED modules, and LED module connections.
X
X
X
Check all condenser coils (fronts and backs) for dust and debris; if present, clear the debris.
X
X
X
Check physical condition of all condenser coils and evaporator coils; straighten coil fins as needed.
X
X
Check all evaporator coils for dust and debris; if present, clear the debris.
X
X
Verify the drain line is clear of debris.
X
X
Page 38 of 56
01/23/2024
P#803294
TEC_TM_043 | REV. G | EN
Maintenance & Servicing (cont.)
TBR/TDR
truemfg.com
Model:
Serial Number:
Jan. Feb. Mar. Apr. May Jun. Jul. Aug. Sep. Oct. Nov. Dec.
TEC_TM_043 | REV. G | EN
01/23/2024
Page 39 of 56
TBR/TDR
truemfg.com
Maintenance & Servicing (cont.)
Draft Tower Cleaning
Regardless of design, draft dispensers must be cleaned regularly. Flushing the
draft dispenser with only water is not enough to maintain cleanliness. True
recommends cleaning the draught dispenser whenever changing to a fresh keg.
Clean dispensers ensure your draft beer will be at its best when served.
Although the beer in the barrel is in excellent condition, the beer can become
less satisfying if drawn through a beer line and faucet that are not kept
clean.
NOTICE > Use cleaners approved by your beer supplier and follow their
instructions. If you are using the cleaning kit purchased from TRUE, follow
the instructions below:
Prepare Solution Add 1/2 oz. (14.2 g) of cleaning solution to each quart of
warm water. Fill the pump bottle with the mixed cleaning solution.
Procedure 1. Shut-off the CO at the regulator.
2. Remove the tapping device (keg coupler) from the keg.
3. Unscrew the handle the from faucet.
4. Remove the beer faucet with the spanner wrench; turn the faucet clockwise
to remove. See fig. 1.
5. Put the tap and faucet parts in a bucket.
6. Thread the pump bottle hose to the beer column tap outlet and allow the
beer line to drain in the bucket. See fig. 2. NOTICE > Be sure the rubber
gasket is in place to prevent leaks.
7. Pump the solution from the bottle through the beer line(s) and into the
bucket. Wait 10 minutes while the cleaning solution works through the lines.
8. With the supplied brush, clean the beer faucet parts. See fig. 3.
9. Rinse all parts thoroughly.
10. Rinse the bucket, pump bottle and hose thoroughly with clean cool water.
11. Fill the pump bottle with clean cool water and pump water through lines
until it runs clear. Repeat as necessary.
12. After the water runs clear, assemble and install the faucet. Then re-tap
the keg.
Beer Tap Cleaning Kit Required Tools
BLC System Cleaner
Spanner Wrench
Brush
Rubber Gasket
Pump Bottle & Tube
Rubber Gasket
Bucket & Fresh Water
Page 40 of 56
Fig. 1. Carefully remove the faucet.
Fig. 2. Drain the beer from the line.
01/23/2024
P#803294
Fig. 3. Thoroughly clean the faucet components.
TEC_TM_043 | REV. G | EN
Maintenance & Servicing (cont.)
TBR/TDR
Condenser Coil Cleaning
WARNING!
The appliance owner is responsible for performing a Personal Protective
Equipment (PPE) Hazard Assessment and ensuring adequate protection during
maintenance and cleaning procedures. Use appropriate tools, safety equipment,
and PPE during installation and servicing.
Risk of electric shock or burn! · Unplug the appliance or turn off the power
supply
before installation or servicing. · DO NOT clean appliance with a pressure
washer or
hose.
Sharp edges! Coil fins are sharp and metal components can have sharp edges.
Take care when moving, installing, cleaning, servicing, and maintaining the
appliance to avoid cuts.
Risk of eye injury! Airborne dust and debris can cause eye injury. Eye
protection recommended.
NOTICE!
The cleaning of the condenser coil is not covered by warranty!
Required Tools Required tools include (but may not be limited to) the
following:
· 1/4″ nut driver
· 3/8″ nut driver
· Stiff bristle brush
· Tank of compressed air
· Vacuum cleaner
· Flashlight
· Eye protection
Procedure 1. Disconnect power to unit.
2. Remove the screw securing the louvered grill to the cabinet. See fig. 1.
3. Pull on the grill assembly to release it from the magnetic brackets. See
fig. 2.
4. Carefully clean off accumulated dirt from the front fins of the condensing
coil with a stiff bristle brush. See fig. 3.
5. With dirt removed from the surface of the coil, use a flashlight to verify
that you can see through the coil and observe the condenser fan blade
spinning. See fig. 4. If the view is clear, reinstall louvered grill, connect
unit to power and verify operation. If the view is still blocked with dirt,
proceed to step 6.
6. Remove the condenser base bolts. See fig. 5.
7. Remove the condenser coil brackets. See fig. 6.
8. Carefully slide the condensing unit out (tubing connections are flexible).
See fig. 7. Gently blow compressed air or CO through the coil until it is
clean.
9. Carefully vacuum any dirt around and behind the condensing unit area.
10. Carefully slide the compressor assembly back into position and replace
the bolts.
11. Reinstall the louvered grill, connect power to the unit, and verify
operation.
TEC_TM_043 | REV. G | EN
01/23/2024
Page 41 of 56
Maintenance & Servicing (cont.)
TBR/TDR
truemfg.com
Fig. 1. Louver grill screw location.
Fig. 2. Pull the grill forward before lifting up.
Fig. 3. Never brush across the coil fins.
Fig. 4. Verify all blockages have been removed.
Fig. 5. Remove the condensing base bolts.
Fig. 7. Carefully slide the condensing unit out. Page 42 of 56
Fig. 6. Remove the coil brackets.
Additional Information If you have any questions, please contact your local
TRUE Manufacturing Service Department. See the front cover for locations and
contact information.
· Do not place any filter material in front of the condensing coil.
01/23/2024
P#803294
TEC_TM_043 | REV. G | EN
Maintenance & Servicing (cont.)
TBR/TDR
truemfg.com
General Surface Care & Cleaning
WARNING!
Risk of electrical shock or fire! DO NOT clean appliance with a pressure
washer or hose.
Slippery Surfaces! Moisture from improper drainage can create slippery
surfaces near the appliance. It is your duty to immediately warn your
customers of, and dry, the slippery surface. All wet floor areas must be
marked with a wet floor sign.
The appliance owner is responsible for performing a Personal Protective
Equipment (PPE) Hazard Assessment and to ensure adequate protection during
maintenance and cleaning procedures. Use appropriate tools, safety equipment,
and PPE during installation and servicing.
Gaskets · Clean gaskets with warm soapy water.
· DO NOT use sharp tools or knives to scrape a gasket.
· Avoid full-strength cleaning products.
Interior · Clean interior surfaces with a mild solution of baking soda and
water to help reduce odor; DO NOT use harsh or abrasive cleaners.
· For plastic or powder-coated parts, use warm soapy water to clean DO NOT use
stainless steel cleaners or similar solvents.
Exterior · For plastic or powder-coated parts, use warm soapy water to clean
DO NOT use stainless steel cleaners or similar solvents.
· DO NOT clean stainless steel with steel wool or abrasive products. DO NOT
use detergents or degreasers with chlorides or phosphates. See model-specific
manual for more information.
TEC_TM_043 | REV. G | EN
01/23/2024
Page 43 of 56
Maintenance & Servicing (cont.)
TBR/TDR
Stainless Steel Care & Cleaning
USER ACTION
DO NOT use any steel wool, abrasive, or chlorinebased products to clean
stainless steel surfaces.
Stainless Steel Opponents There are three basic things which can break down
your stainless steel’s passivity layer and allow corrosion to form.
· Scratches from wire brushes, scrapers, steel pads, and other items that can
be abrasive to stainless steel’s surface.
· Deposits left on your stainless steel can leave spots. You may have hard or
soft water depending on what part of the country you live in. Hard water can
leave spots. Hard water that is heated can leave deposits if left to sit too
long. These deposits can cause the passive layer to break down and rust your
stainless steel. All deposits left from food prep or service should be removed
as soon as possible.
· Chlorides which are present in table salt, food and water, as well as in
household and industrial cleaners. These are the worst type of chlorides to
use on stainless steel.
Stainless Steel Cleaning and Restoration Stainless steel cleaners must be free
of phosphates, chlorine, chloride, and ammonia.
True offers environmentally-friendly cleaner and polish through our True Store
at store.trueresidential.com/products/stainless-steel-clean-polish-
kit.
Custom Painted Appliance and Hardware For painted doors and other surfaces,
use a mild solution of soap and water with a soft microfiber cloth.
Page 44 of 56
01/23/2024
P#803294
TEC_TM_043 | REV. G | EN
Maintenance & Servicing (cont.)
TBR/TDR
8 Tips to Help Prevent Rust on Stainless Steel
Maintain the Cleanliness of Your Equipment
Avoid build-up of hard stains by cleaning frequently. Use cleaners at the
recommended strength (alkaline chlorinated or non-chloride).
Use the Correct Cleaning Tools
Use non-abrasive tools when cleaning your stainless steel products. The
stainless steel’s passive layer will not be harmed by soft cloths and plastic
scouring pads.
Clean Along Polishing Lines
Polishing lines (“grain”) are visible on some stainless steels. Always scrub
parallel to polishing lines when visible. Use a plastic scouring pad or soft
cloth when you cannot see the grain.
Use Alkaline, Alkaline-Chlorinated or Non-Chloride Cleaners
While many traditional cleaners are loaded with chlorides, the industry is
providing an ever increasing choice of non-chloride cleaners. If you are not
sure of your cleaner’s chloride content, contact your cleaner supplier. If
they tell you that your present cleaner contains chlorides, ask if they have
an alternative. Avoid cleaners containing quaternary salts, as they can attack
stainless steel, causing pitting and rusting.
Rinse
When using chlorinated cleaners, you must rinse and wipe dry immediately. It
is better to wipe standing cleaning agents and water as soon as possible.
Allow the stainless steel equipment to air dry. Oxygen helps maintain the
passivity film on stainless steel.
Never Use Hydrochloric Acid (Muriatic Acid) on Stainless Steel
Even diluted, hydrochloric acid can cause corrosion, pitting and stress
corrosion cracking of stainless steel.
Water Treatment
To reduce deposits, soften hard water when possible. Installation of certain
filters can remove corrosive and distasteful elements. Salts in a properly
maintained water softener can also be to your advantage. Contact a treatment
specialist if you are not sure of the proper water treatment.
Regularly Restore & Passivate Stainless Steel
Stainless steel gets its stainless properties from the protective chromium
oxides on its surface. If these oxides are removed by scouring, or by reaction
with harmful chemicals, then the iron in the steel is exposed and can begin to
oxidize, or rust. Passivation is a chemical process that removes free iron and
other contaminants from the surface of stainless steel, allowing the
protective chromium oxides to re-form.
TEC_TM_043 | REV. G | EN
01/23/2024
Page 45 of 56
Maintenance & Servicing (cont.)
TBR/TDR
Reverse Door Swing Style #1
Kit Contents (shipped with cabinet)
· Bottom hinge bracket
· Door cam base and riser
· Top hinge bracket
· Top hinge bushing
Required Tool(s) · Phillips screwdriver
· 5/16″ socket wrench
· Flat blade screwdriver
NOTICE > Make appliance adjustments after verifying the cabinet is level and
supported properly. The example shown is a left hinge door changing to a right
hinge door. Procedure
1. Locate and remove the bolts securing the top hinge bracket to the front of
the appliance base. Remove the bolts. See fig. 1.
2. With the bolts removed, swing the bracket onto the door. Tilt the top of
the door out to provide clearance from the countertop. Lift the door to
disengage it from the top hinge bracket. See fig. 2.
3. Remove the bottom hinge assembly from the appliance. See fig. 3.
Fig. 1. Top hinge bolt locations. Fig. 2. Remove the top hinge from the unit.
truemfg.com
Fig. 4a. Top hinge components. Page 46 of 56
Fig. 3. Lift the door off the bottom hinge.
Door Top
Top hinge bracket and shaft
Top hinge bushing
Door bracket
Fig. 4b. Bottom hinge components.
01/23/2024
P#803294
Door Bottom
Door bracket
Door cam riser
Components not on the door but included in the assembly. Door cam base Bottom
hinge bracket and shaft
TEC_TM_043 | REV. G | EN
Maintenance & Servicing (cont.)
TBR/TDR
truemfg.com
Reverse Door Swing (cont.)
4. Remove all door hardware except the door handle (see figs. 4a and 4b). Set
the door brackets aside. NOTICE > The door brackets are the only hardware that
will be relocated. All other hardware is new and included in the kit. Door
brackets are reversible to the opposite diagonal corner of the door. See fig.
5.
5. Remove any door plugs and all screws on the opposite side of the original
door hinge placement. See fig. 6.
6. Install all hardware into the door’s new component locations.
Door Bottom (see fig. 7a)
a. Install the bottom door bracket.
b. Install the door cam riser.
Door Top (see fig. 7b)
a. Install the top door bracket.
b. Install the top hinge bushing.
c. Install top hinge bracket and shaft.
7. Insert the screws into the holes opposite their original location. See
fig. 8.
8. Install the bottom hinge bracket and shaft to the appliance. See fig. 9.
a. Install the door cam base to hinge shaft.
b. Lift door onto bottom door hinge bracket and shaft.
9. Secure the top hinge bracket to the cabinet. See fig. 10. NOTICE > Top
hinge bracket is slotted for door alignment.
10. Install plug in door in top of door (see fig. 11). Verify correct door
operation.
Fig. 5. The current bottom door bracket will be the new top door bracket.
1 2
Fig. 7a. Bottom hinge component assembly.
Fig. 8. Move the hardware from step 5 to the side opposite its original
location.
Fig. 6. Remove the door plugs and remaining screws.
3 2
1
Fig. 7b. Top hinge component assembly.
2
1
Fig. 9. Install the bottom hinge pin in its new location.
2 1
TEC_TM_043 | REV. G | EN
Fig. 10. Install the top hinge and the door. 01/23/2024
Fig. 11. Install the plug.
Page 47 of 56
Maintenance & Servicing (cont.)
TBR/TDR
truemfg.com
Reverse Door Swing Style #2
Kit Contents (shipped with appliance)
· Bottom hinge bracket
· Door cam base and riser
· Top hinge bracket
· Top hinge bushing
Required Tool(s) Required tools include (but may be limited to) the following:
· Phillips screwdriver · 5/16″ socket wrench · Flat blade screwdriver · Drill
(optional)
Procedure NOTICE > The example shown is a left hinge door changing
to a right hinge door. Save removed hardware, if so desired, for future door
reversals. 1. Locate and remove the hardware securing the top hinge
bracket to the front of the appliance. See fig. 1.
2. With the hardware removed, open and lift the door to disengage it from the
bottom hinge bracket. See fig. 2.
3. Remove the bottom hinge assembly from the appliance. See fig. 3.
4. Remove the remaining hardware from the top and bottom of the appliance on
the opposite side of the door opening. See fig. 4.
5. Remove the door plug and top hinge bushing from the top of the door. Then,
switch their positions. See fig. 5.
6. Install the new cam riser on the bottom of the door on the opposite side
of its original location. See fig. 6.
7. Install the new bottom hinge bracket on the opposite side of the door
opening. See fig. 7.
8. Position the door on the bottom door hinge bracket.
9. Insert the new top hinge into the door. Then, install the top hinge
bracket onto the appliance.
10.Verify door operation and alignment. Adjust door as needed.
NOTICE > The top hinge brackets are slotted to allow for door adjustment.
Fig. 1. Remove the bolts securing the top hinge brackets.
Fig. 2. Lift the door to disengage it from the bottom hinge.
Fig. 3. Lift the door off the bottom hinge.
Fig. 4. Remove the remaining hardware from the top and bottom of the appliance on the opposite side of the door opening.
Fig. 5. Remove the door plug.
Fig. 6. Install the cam riser on the bottom of the door on the opposite side of its original location.
Page 48 of 56
Fig. 7. Install the bottom hinge on the opposite side of the door opening.
01/23/2024
P#803294
TEC_TM_043 | REV. G | EN
Maintenance & Servicing (cont.)
TBR/TDR
Slide Door Removal
USER ACTION
· DO NOT use the side latch before removing the slide door. The tension on the
door cord is needed to execute these operation instructions.
· Doors CANNOT be removed unless they are positioned as stated in these
instructions.
Procedure 1. Position the doors as described below. To remove, lift the
positioned door. Then, tilt the top of the door back until the rollers exit
the door channel. Then, swing the bottom of the door out of the bottom
channel. See figs. 1 and 2. Two-Door Units Center the front door on the
cabinet opening. See fig. 3.
Three-Door Units See fig. 4 · Center Door: Slide 9 ” (228.6 mm) right
· Right Door: Slide 14″ (355.6 mm) left
· Left Door: Slide 9-1/2″ (241.3 mm) right
Continued on next page…
Fig. 1. Door channel openings. Fig. 2. Carefully remove the door.
CENTERED DOOR
LEFT 9-1/2″ 241.3 mm
CENTER 9″
228.6 mm
RIGHT 14″ 355.6 mm
Fig. 3. Two-Door Units: Position the front door at the center of the cabinet.
Fig. 4. Three-Door Units: Move the doors as directed to remove doors from channel.
TEC_TM_043 | REV. G | EN
01/23/2024
Page 49 of 56
Maintenance & Servicing (cont.)
TBR/TDR
Slide Door Removal (cont.)
2. Remove the door cord from the roller bracket. See figs. 5 and 6.
NOTICE > The black plastic tab holding the door cord slides out the back.
3. Let the door cord slowly retract back into the door side channel.
NOTICE > When reinstalling the door, be sure the door cord grommet attaches to
roller slot closest to the pulley. See fig. 7.
Fig. 5. Remove the door cord from the roller bracket.
truemfg.com
Fig. 6. Slide the the black tab holding the door cord out the back.
Page 50 of 56
Fig. 7. Be sure the door cord is in the roller slot closest to the pulley.
01/23/2024
P#803294
TEC_TM_043 | REV. G | EN
Maintenance & Servicing (cont.)
TBR/TDR
truemfg.com
Slide Door Adjustment
Only adjust the appliances after it has been installed in its final location
and correctly leveled.
Procedure
1. Completely close the slide doors and check for openings. If there are any
gaps/openings between the closed doors and appliance, the doors will need to
be adjusted.
2. With a 7/16″ wrench or adjustable wrench and 1/8″ Allen wrench, loosen the
roller and move it along the slotted hole. After the adjustment has been made
tighten the roller into place. See fig. 1.
Slide Door Hold-Open Feature
The hold-open feature keeps the door in the open position.
Procedure 1. Slide the door open.
2. Latch the door in the open position from the back side of door (notch in
track). See figs. 1 and 2. NOTICE > Figs. 1 and 2 show the rear view of the
door
and track.
Fig. 1. Adjust the roller.
Fig. 1. Door latch is in the open position (engaged with notch). Fig. 2. Door latch is in the closed position (disengaged from notch).
TEC_TM_043 | REV. G | EN
01/23/2024
Page 51 of 56
TBR/TDR
truemfg.com
Maintenance & Servicing (cont.)
Gasket Replacement
Tools Required · Caulk gun
· Black 100% silicone
There are two types of door gaskets; narrow and wide gaskets (see fig 1). The
correct gasket for your unit varies by appliance age and model. The gaskets
are NOT interchangeable.
NOTICE > For narrow gaskets, it’s important to remember which track the gasket
was removed from. Normally, the gasket is in the center track on the top,
bottom, and handle sides. On the hinge side, it’s on the inside track.
Procedure 1. From the upper right or left-hand corner, carefully pull
removable gasket away from the door. See fig. 2.
2. Apply silicone to each corner of the door/gasket channel. See fig. 3.
3. After applying silicone to the corners, push the gaskets back into their
original tracks. Press corners in NOTICE > The silicone will seal any possible
air leaks. Excess silicone should seep out of the track.
4. Clean any excess silicone.
NOTICE > Gasket color may vary depending on unit.
A B
Fig. 1. There are two gasket types. A: Narrow gasket; B: Wide gasket.
Fig. 2. Pull the gasket starting at an upper corner.
Fig. 3. Apply silicone to each corner of the gasket channel. Page 52 of 56
Fig. 4. It is common to see silicone pushed out of track around the gasket. This is how you know enough silicone was used.
01/23/2024
P#803294
TEC_TM_043 | REV. G | EN
TBR/TDR
Maintenance & Servicing (cont.)
Swing Door Lock & Cam Replacement
The door must be open prior to proceeding.
Procedure — Removing Components 1. Insert the master key (included with the
replacement lock kit)
into the lock cylinder. 2. Turn the key and pull to remove the cylinder from
the lock
barrel. 3. Slide the lock cam/bar out of the bottom of the lock barrel.
Procedure — Installing Components 1. Slide the lock cam/bar into the bottom of
the lock barrel. 2. Push the lock cylinder with master key into the lock
barrel.
NOTICE > Ensure the pin of the back of the lock cylinder aligns with the notch
in the lock cam/bar. See fig. 3.
truemfg.com
2
1 3
Fig. 1. Front view of removing/installing components.
1
2
3
Fig. 2. Bottom view of removing/installing components.
Fig. 3. Lock cam/bar notch
TEC_TM_043 | REV. G | EN
01/23/2024
Page 53 of 56
TBR/TDR
Warranty Information (USA & Canada Only)
Warranty Information
To view and download the Warranty Information for USA & Canada,
please scan the QR code below.
Page 54 of 56
01/23/2024
P#803294
TEC_TM_043 | REV. G | EN
NOTES
TBR/TDR
TEC_TM_043 | REV. G | EN
01/23/2024
Page 55 of 56
BC_217376_10.23
01/23/2024
P#803294
TEC_TM_043 | REV. G | EN
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>