KOZYARD KZAHG1218GRA Alexander Hardtop Gazebo Double Roof Instruction Manual

KZAHG1218GRA Alexander Hardtop Gazebo Double Roof

Specifications

• Product Name: 12’x18′ Alexander Hardtop Gazebo With Double Roof
• Manufacturer: Kozyard LLC
• Website: www.kozyard.com
• Version: 20231006

Warnings and Cautions:=

• Two or more people are required for assembly and disassembly.
• Do not fully tighten screws prior to complete assembly.

Pre-assembly
Tools that may be required. (Not included in boxes)
Note: Tools are not shown to actual size and scale.

Attention
Prior to assembly, verify that all parts and pieces are included to ensure an efficient installation process.

Item Descriptions

Assembly Manual

Warnings and Cautions

• Please read and follow this assembly and operation guide to reduce the risk of personal injury and damage to your gazebo.
• Do not discard any of the packaging until you have checked that you have all the parts in place. The maximum weight capacity of this gazebo roof is 2500 pounds.
• Sidewalls and nettings should be off or in the opened position and tied to poles when winds are over 30 MPH to avoid damage.
• Some parts may have sharp edges or corners. To ensure your safety, follow basic safety precau-tions to reduce the risk of injury. Please note that this item contains small parts which could be swallowed by children. Keep it out of reach of children under 3 years old and pets during installation.

Pre-assembly
Tools that may be required.(Not included in boxes) Note: Tools are not shown to actual size and scale.

12×18′ ANCHOR BLUEPRINT

Attention : Prior to assembly, verify that all parts and pieces are included to ensure an efficient installation process.

1. Step 1: Set up Poles
   Set up Poles (Part A,A1) with Stand Plates (Part L, L1) using screws 1# as shown in the diagram.
   

2. Step 2: Connect the Beams
   Connect (Part C6,B6) into one beam using Union bar (Part F) with screws 1# as shown in the diagram.

3. 1.  Connect Parts (B61, B91, B62) to Part (B6) using screw 1#, as shown in the diagram.

4. Replicate the same steps for Parts(C61,C91,C62) attaching them to Parts (C6) using screws 1# as shown in the diagram.

5. Connect Parts (E91L,E91R) to Parts (E9) using screws 1# as shown in the diagram.

• Step 4： Set up Poles and Beams
  Use screws 3# first, then screw 2# to connect Poles and Beams together as shown in diagram.

• Step 5: Connect Solidifying Bars with Beams and Poles
  Affix the frame with Corner Solidifying Bars (Part J1,J2) using screws 1# as shown in the diagram.

• Step 6: Cover the connections

  1. Finish Connecting Beams using Corner Covers (Part G) and screws 9# as shown in the diagram.
     2. Affix the middle beams using Joint Cover (Part H) and screws 9# and 1# as shown in the diagram.

• Step 7: Seal the seams

  1. After finishing Step 6, apply silicone rubber to the seams to ensure they’re watertight.
  2. If the screws are correctly attached through Spacer part S on the roof panels, sealing the cap screws with silicone rubber isn’t necessary.

• Step 8: Install Hooks
  After finishing Hooks (Part 4#) into the tracks, then put Joint Cover (Part H1) to lock them .
  

• Step 9: Connect Corner Roof Bar “M3”
  Connect Short Corner Roof Bar (Part M1) with Long Corner Roof Bar (Part M2) using screws 1# and washer 12#.

• Step 10: Set up roof frame

• Step 11: Set up Roof Bar
  1. Attach the finishing bar (Part P2, Q7, Q8) with the finishing end (Part R) using screw 1# to the corner roof bar (Part M3) as shown in the diagram.

• Step 12: Connect Outside Roof Connctor
  C onnect the Outside Roof Connector (Part K18) to the Inside Roof Connector (Part K8) using screw 1#, as shown in the diagram.

• Step 13: Snap Bracket
  Snap Bracket (Part Z, Z1, Z2,Z3,Z4) to the roof panel edges as shown in the diagram.(with snaps facing upwards)

  • Wearing protective gloves is recommended.
  • To prevent Z-Clips (plastic brackets) from sliding off prior to assembly, apply double-sided adhesive tape (Part H3) to the underside (bottom) edge of the roof panels where the brackets (Part Z, Z1, Z2) are supposed to attach.
  • You can use super glue (not included) to attach the brackets to the roof panel if the double-sided tape doesn’t work for you

• Step 14: Assemble Roof Panel

  1. Push the Roof Panels (Part V11, V12, V83, V68,V,V, V85,V86) up to the upper roof as shown in the diagram.
     Attach Finishing Bars (Part T2, T7, T8) to the upper roof with Finish End (Part R) using screws #1, as shown in the diagram.

• Step 15:Connect Solidifying Bars

  1.  Attach Solidifying Bars ( Part U1, U7, U8) to Roof Bar or Corner Roof Bar using Iron Angle (Part U3, U4) and screws 1# as shown in the diagram.

• Step 16: Snap Bracket
  Snap Brackets (Part Z) to roof panel edges as shown in the diagram. (with snaps facing upwards)

• Step 17: Snap Bracket
  Snap Brackets (Part Z, Z3, Z4) to roof panel edges as shown in the diagram. (with snaps facing upwards)

Overall roof assembly:

Please place the panels on the frame and assemble them from the centerline (Part N1, N2) to the left and right.

• Step 18: Affix roof panels using screws and Spacers (Part S) as shown in the diagram.
  Align all roof panels and screws LOOSELY (DO NOT TIGHTEN ANY SCREWS) until all the roof panels are aligned accordingly. THEN, TIGHTEN all screws to secure the roof panels in place.

•  Step 19: Assemble Net Frames
  Attach net frame (Part P12, Q17, Q18) to finishing bar（Part P2, Q7, Q8) using screws (1#, 11#) as shown in the diagram.

• Step 20: Assemble Net and Sidewall
  Hang the Mosquito Net on the inner rails and the Solid Sidewalls on the outer rails as shown in the diagram.

Care and Warranty

• Clean the frame components and fabric with a mild soap solution, then rinse thoroughly. Avoid using bleach, acid, or any other solvents on either the fabric or frame components.
• The roof, frame, bolts, and nuts come with a guarantee against defects in material and workman-ship for one year from the date of purchase. However, the privacy curtain and mosquito netting are warranted for just 90 days. For a comprehensive warranty policy, please visit www.koz-yard.com. Be aware that warranty terms can change without prior notification.
• For the best performance and safety of your gazebo, inspect and tighten all bolts and fasteners regularly

As expert manufacturer of hardtop gazebos, Kozyard remains committed to supporting you with parts and replacements, even beyond your warranty period.
Don’t hesitate to contact us directly if you are missing parts or need a replacement.

SUPPORT: Toll free: 1-866-355-0018 www.kozyard.com email: support@kozyard.com
SOCIAL MEDIA : Follow us on Instagram www.instagram.com/kozyard

References

• Kozyard LLC Official Web Site

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>