KOZYARD KZPHG1220 Wood Grain Hardtop Gazebo Mosquito Netting Instruction Manual
- June 17, 2024
- KOZYARD
Table of Contents
- KZPHG1220 Wood Grain Hardtop Gazebo Mosquito Netting
- Product Information
- Specifications
- Warnings and Cautions
- Assembly Instructions
- Step 1: Set up Poles
- Step 2: Attach Beam and Jointer Bars
- Step 3: Install Sidewall Tracks
- Step 4: Connect Roof Bars
- Step 5: Attach Roof Panels
- Q: Is anchoring poles into concrete necessary?
- Q: How many people are required for assembly?
- Q: Are all the necessary parts included?
KZPHG1220 Wood Grain Hardtop Gazebo Mosquito Netting
Product Information
Specifications
-
Product Name: 12’x20′ Alexander Hardtop Gazebo With Double
Roof -
Manufacturer: Kozyard LLC
-
Website: www.kozyard.com
-
Version: 20231006
Warnings and Cautions
Two or more people are required for assembly and
disassembly.
Pre-assembly:
-
Tools that may be required (Not included in boxes): Safety
glasses, Screwdriver, Allen key, Wrench -
Do not fully tighten screws prior to complete assembly.
Assembly Instructions
Step 1: Set up Poles
Parts Required: Set up Poles (Part A, A1) with Stand Plates
(Part L, L1) using screws 1# as shown in the diagram.
Step 2: Attach Beam and Jointer Bars
Parts Required: Attach Beam (Part B6, C6) and Jointer Bars (Part
B21, C21) to the Poles using screws 2# as shown in the diagram.
Step 3: Install Sidewall Tracks
Parts Required: Install Sidewall Tracks (Part B62, C62) and
Jointer Bars (Part E21L, E21R) to the Poles and Beams using screws
3# as shown in the diagram.
Step 4: Connect Roof Bars
Parts Required: Connect Roof Bars (Part N1, N2, N3) using Roof
Connectors (Part K10, K20) and screws 4# as shown in the
diagram.
Step 5: Attach Roof Panels
Parts Required: Attach Roof Panels (Part X21-X32) to the Roof
Bars using screws 5# as shown in the diagram.
FAQ
Q: Is anchoring poles into concrete necessary?
A: Anchoring poles into concrete is strongly recommended to
ensure stability.
Q: How many people are required for assembly?
A: Two or more people are required for assembly and
disassembly.
Q: Are all the necessary parts included?
A: Prior to assembly, verify that all parts and pieces are
included to ensure an efficient installation process.
12’x20′ Alexander Hardtop Gazebo With Double Roof
Assembly Manual
Kozyard LLC Products
www.kozyard.com
© Copyright 2016 – 2023 Kozyard LLC. | All Rights Reserved.
Version:20231006
Warnings and Cautions
· Please read and follow this assembly and operation guide to reduce the risk
of personal injury and damage to your gazebo.
· Do not discard any of the packaging until you have checked that you have all
the parts in place. The maximum weight capacity of this gazebo roof is 2500
pounds.
· Sidewalls and nettings should be off or in the opened position and tied to
poles when winds are over 30 MPH to avoid damage.
· Some parts may have sharp edges or corners. To ensure your safety, follow
basic safety precautions to reduce the risk of injury. Please note that this
item contains small parts which could be swallowed by children. Keep it out of
reach of children under 3 years old and pets during installation.
Two or more people are required
2+
for aseembly and disassembly.
Pre-assembly
Tools that may be required.(Not included in boxes) Note: Tools are not shown
to actual size and scale.
Do not fully tighten screw prior to complete assembly.
6.77 in
12×20′ ANCHOR BLUEPRINT
Safetyglasses
12 in.
12 in.
136.88 in. ø0 .31 in.
136.53 in.
111.85 in.
111.85 in.
Anchoring poles into concrete is strongly recommended. Ensure the gazebo is positioned on level ground
Attention: Prior to assembly, verify that all parts and pieces are included to
ensure an efficient installation process.
A x4
K10 x1
E21L x2 E22L x2
F x6 H1 x6
J1 x4 L x4
A1 x2 B6 x4 B61 x2 B62 x4 B21 x2
C6 x4
C61 x2
C62 x4 C21 x2
E21R x2 E22R x2
E2 x2
G x4
H x6
H2 x1
H3 x1 J2 x4 L1 x2
K20 x1
M4 x4
N1 x2
N2 x2
N3 x4
ITEM DESCRIPTION
QTY
A Pole
4
A1 Pole
2
B6 Beam
4
B61 Jointer Bar
2
B62 Sidewall Track
4
B21 Jointer Bar
2
C6 Beam
4
C61 Jointer Bar
2
C62 Sidewall Track
4
C21 Jointer Bar
2
E2 Beam
2
E21L Jointer Bar
2
E21R Jointer Bar
2
E22L Sidewall Track
2
E22R Sidewall Track
2
F
Union Bar
6
G Corner Cover
4
H Joint Cover
6
H1 Joint Cover
6
H2 Silcone Rubber
1
H3 Double-sided adhesive tape
1
J1 Corner Solidifyng Bar
4
J2 Corner Solidifyng Bar
4
K10 Inside Roof Connector
1
K20 Outside Roof Connector 1
L
Plate
4
L1 Plate
2
M4 Corner Roof Bar
4
N1 Roof Bar
2
N2 Roof Bar
2
N3 Roof Bar
4
12’x20′ assembly manual
page 1
P2 x2
P12 x2 Q9 x2 Q10 x2 Q19 x2 Q20 x2
W11 x2 W12 x2 W13 x2 W14 x2
R x8
R1 x2
S x160 T2 x2 T9 x2 T10 x2 U1 x4 U9 x4 U10 x4
U3 x4
U4 x8
V11 x2 V12 x2
V23 x2 V24 x2 V x8
V25 x2 V26 x2
W15 x2 W16 x2 W17 x2 W18 x2
ITEM
P2 P12 Q9 Q10 Q19 Q20 R
R1
S T2 T9
T10 U1 U3 U4 U9 U10 V11 V12 V23
V24 V V25 V26 W11 W12 W13 W14 W15 W16 W17 W18
DESCRIPTION Finishing Bar Net Frame Finishing Bar Finishing Bar Net Frame Net
Frame Finishing End
Finishing End Spacer Finishing Bar Finishing Bar Finishing Bar Solidifying Bar
Iron Angle Iron Angle Solidifying Bar Solidifying Bar Roof Panel Roof Panel
Roof Panel Roof Panel Roof Panel Roof Panel Roof Panel Roof Panel Roof Panel
Roof Panel Roof Panel
Roof Panel Roof Panel Roof Panel
Roof Panel
QTY 2
2 2 2 2 2 8 2 160 2 2 2
4 4 8 4 4 2 2 2 2 8
2 2 2 2 2 2 2 2 2 2
12’x20′ assembly manual
page 2
X21 x2 X22 x2 X23 x2 X24 x2 X25 x2 X26 x2
6# x8+1 7# x48+2 8# x6+1 9# x28+2 10# x4+1 11# x12+1
X27 x2 X28 x2 X29 x2 X30 x2 X31 x2 X32 x2
Y7 x4 Z x72+2
Y9 x2
Z1 x6
Z2 x6
Z3 x2
Z4 x2
4# x76+2 1# x301+5 2# x28+2
12×20+M6x12
3# x16+2
5# x100+2
ITEM DESCRIPTION
X21 Roof Panel X22 Roof Panel X23 Roof Panel X24 Roof Panel X25 Roof Panel X26
Roof Panel X27 Roof Panel X28 Roof Panel X29 Roof Panel X30 Roof Panel X31
Roof Panel X32 Roof Panel Y7/Y9 Mosquito Net
Z Bracket Z1 Bracket Z2 Bracket Z3 Bracket Z4 Bracket 1# Screws
2# Screws 3# Screws 4# Hook 5# Screws
6# Screws 7# Screws 8# Screws 9# Screws 10# Screws
11# Screws
12’x20′ assembly manual
Allen key
Wrench
Screw Driver
QTY 2 2 2 2 2 2 2 2 2 2 2 2 6
72+2 6 6 2 2
301+5 28+2 16+2 76+2 100+2 8+1 48+2 6+1 28+2 4+1 12+1
page 3
Step 1:Set up Poles
Parts Required: Set up Poles (Part A, A1) with Stand Plates (Part L , L1)
using screws 1# as
shown in diagram.
X4
A
1#
1#
A
1#
A x4
L
L x4 1# x12
A1 x2
L
A1 1#
A1 1#
Reference for anchoring gazebo:
· If the ground is concrete and
its depth is over 3 inches,
you can purchase 3/8″ diam-
eter x 3″ length sleeve
1#
anchors.
· Only anchor after finishing all
the assembly.
1#
3 inches
3/8 inches
M6
X12
L1
(Not included)
X2
L1 x2
1# x8
After assembly, we strongly recommend anchoring the
L1
gazebo to your deck or concrete as shown above.
Damage resulting from wind or improper anchoring is
not covered under warranty.
12’x20′ assembly manual
page 4
Parts Required:
C6 x4
F x6
B6 x4
1#
E2 x2
x24
Step 2: Connect the Beams
1. Connect (Part C6,B6) into one beam using Union bar (Part F) with screws 1#
as shown in the diagram.
Short Beam Overall:
C6
B6
X2
F
B6
B6
X2
C6
C6
F 1#
1# 1#
1#
2. Connect (Part C6, E2, B6) into one beam using Union Bar (Part F) with screws 1#
as shown in the diagram.
X2
Long Beam Overall:
C6
E2
B6
F
X2
C6 F
1#
F
E2
1#
B6 1# 1#
Tip:
12’x20′ assembly manual
page 5
Parts Required:
C61 x2 C62 x2
C21 x2
E21L x2
E21R x2
C62 x2
1# x108
Step 3Connect Joint Bars with Beams
12 ft overall:
C61
B61
B61 x2 B62 x2
B21 x2
B62 x2
20 ft overall: C21
C62 C6
E21L
B62 B6
E21R
B21
C6
C62
B6
1#
E2
Tip: Do not tighten all screws on Jointer Bar (Part
B61,C61,B21,E21R,E21L,C21), until the screws of the roof panels be aligned in
place.
B62 B6 C6
1#
1#
B62
X2 B61,B21
X2 C61,C21
1#
C62
1. Connect Joint Bars (Part B61,B21) and
Tracks (Part B62) to Beams (Part B6) using screws 1# as shown in diagram.
2. Replicate the same steps for Joint Bars
(Part C61,C21) and Tracks (Part C62) attaching them to Beams (Part C6) using
screws 1# as shown in diagram.
3. Connect Joint Bars (Part E21L,E21R) to Beams (Part E2)
using screws 1# as show in diagram.
E2
X2
1#
1# 1# 1# E21R
1#
1#
1#
E21L 1# 1# 1#
Tip:
12’x20′ assembly manual
page 6
Parts Required
E22L x2
E22R x2
2#
x28
1#
x16
3#
x16
Step 4Set up Poles and Beams
Use screws 3# first, then screw 2# to connect Poles and Beams together as shown in diagram.
A
Tip: Place parts on carpet or rug to avoid scratches during assembly.
B6
X2
C6
A
C6
B6
C6
B6
E2
C6
B6
X2
3# 3#
X8
2#
X8
2#
E2
X2
2#
A1
2#
2. Connect Joint Bars (Part E22L,E22R) to Beam
(Part E2) using screws 1# as shown in diagram.
E2
X2
1#
1#
E22L
1#
1#
1#
1#
1#
1#
A1
E22R
C6
B6
A
Tip:
At least three people
3+
for this step.
12’x20′ assembly manual
B6
C6
E2 B6
A
C6
A1
E2
A
C6
B6
A1
A
page 7
Parts Required:
J1 x4
1#
J2 x4
x32
J1
J2
1#
1#
1#
X4
Step 5: Connect Solidifying Bars with Beams and Poles
Affix the frame with Corner Solidifying Bars (Part J1,J2) using screws 1# as
shown in the diagram.
J1 J2
J2 J1
Diagonal 1
J1 J2
Diagonal 2
J2 J1
Diagonal 1 = Diagonal 2
Tip: Measure (DIAGONALLY) from posts to posts to assure alignment so all materials fit as planned.
12’x20′ assembly manual
page 8
Parts Required:
G x4
9#
H x6
x28
Step 6: Cover the connections
1. Finish Connecting Beams using Corner Covers (Part G) and screws 9# as
shown in the diagram.
9# 9#
G
X4
9#
X6
2. Affix Middle Beams using Joint Cover
(Part H) and screws 9# as shown in diagram.
12’x20′ assembly manual
9#
H
page 9
Parts Required:
H2 x1
Step 7: Seal the seams
1. After finishing Step 6, apply silicone rubber to the seams to ensure
they’re watertight. 2. If the screws are correctly attached through Spacer
part S on the roof panels, sealing the cap
screws with silicone rubber isn’t necessary.
X6
12’x20′ assembly manual
page 10
Parts Required:
4#
x76
8#
H1 x6
x6
Step 8: Install Hooks
After finishing Hooks (Part 4#) into the
tracks, then put Joint Cover (Part H1) to
lock them.
4#
4#
X6
4#
Note the amount of hooks for each slot as noted below:
H1 8#
7 Put hooks to each slot of Sidewall Track (Part C62 , Part B62) for 12 ft side
X2
4#
C62
x7
C6
B6
H1
x7
B62
Put 7 hooks to each slot of Sidewall Track Part C62 and 5 hooks to each slot Sidewall track Part E22L for 20 ft side. X2
4#
C62
x7
C6 H1
E2 x5
E22L
Put 5 hooks to each slot of Sidewall Track Part E22R and 7 hooks to each slot Sidewall Track Part B62 for 20 ft side. X2
4#
E22R
E2
x5
x5
B6
B62
H1
x7
x7
12’x20′ assembly manual
page 11
Parts Required:
1#
x36
M4
M4 x4 K10 x1
Step 9: Set up roof frame
hole
N3
1#
N2
1#
N3
1#
hole
N1
1#
1# 1#
Upward View
N3 M4
K10
N2
hole
1# 1#
N3
hole
N1 x2 N2 x2 N3 x4
M4
N1
M4
M4 N3 1# 1#
M4 1#
N2
1#
N3
1#
N1
1# N3
M4 X2
A
X4
A1
X2
1. Connect the inside roof connector (Part K10) with the conner
roof barcPart M4) and roof bar(Part N1,N2,N3) using
screws 1# as shown in diagram.
M4
N3 N2 N3
N1 M4
X4
N1
1#
M4
N1
N3 M4
N3 N2
X2
Tip:
At least two people
2+
for this step.
2. Attach Corner Roof Bar (Part M4) and Roof Bars (Part N1, N2, N3) to the main frame using screw 1# as shown in the diagram.
12’x20′ assembly manual
page 12
Parts Required:
P2 x2
M4
N3 Q9
N2
Q9 x2 Q10 x2
Q10
R x4
N3
1#
x6
M4
N1
P2
Upward View
P2
N1
Q 10
Q9
M4
N3
N2
N3
M4
N2
1# R
P2
Q10
X4
Step 10: Set up Roof Bar
1. Attach the finishing bar (Part P2, Q9, Q10) with the finishing end (Part
R) using screw 1# to the corner roof bar (Part M3) as shown in the diagram.
Q 10
Q9 X2 1#
2. Affix the Finishing Bar (Part Q9, Q10) to the roof bars (Part N2, N3)
using screw 1# as shown in the diagram.
M4
P2
N1
Q10
Q9
N3
N2
N3
M4
12’x20′ assembly manual
page 13
Parts Required:
1#
K20 x1
x5
Upward View
K10 K20
1#
1#
1#
Step 11: Connect Outside Roof Connctor
Connect the Outside Roof Connector (Part K20) to the Inside Roof Connector
(Part K10) using screw 1#, as shown in the diagram.
K 20
12’x20′ assembly manual
page 14
Parts Required:
Z x12 Z1 x4
Z3 x2
V11 x2 V12 x2
V23 x2 V24 x2
V x8
V25 x2 V26 x2
Z2 x4 Z4 x2
Step 12: Snap Bracket
Snap Bracket (Part Z, Z1, Z2, Z3, Z4) to the roof panel edges as shown in the
diagram.
(with snaps facing upwards)
X2
Z1
Z2
H3 x1
Z
Z
Z2
Z Z1
V11
V12
Z
Z
Z4
V23
V24
V
V
Z
Z
Z3
V
V
V25
V26
Tips:
1. Wearing protective gloves is recommended. 2. To prevent Z-Clips (plastic
brackets) from sliding off prior to assembly, apply
double-sided adhesive tape (Part H3) to the underside (bottom) edge of the
roof panels where the brackets (Part Z, Z1, Z2, Z3, Z4) are supposed to
attach. 3. You can use super glue (not included) to attach the brackets to the
roof panel if the double-sided tape doesn’t work for you.
12’x20′ assembly manual
page 15
Parts Required:
T2 x2
R V26 V25 T2 V11
1#
T9 x2
R x4
x12
T10 x2
R1 x2
Upward View
T10 V
V
V
T9 V
V24 V23 R
V12 T2
1#
V12
V11
R
V23 V24
V
V
R
V
V
1#
V25 V26
T9
1#
R1 1#
Step 13Assemble Roof Panel
T10
1# X2
1. Push the Roof Panels (Part V11, V12, V23, V24, V, V, V25, V26) up to the
upper roof as shown in the diagram.
2. Attach Finishing Bars (Part T2, T9, T10) to the upper roof with Finish End
(Part R) using screws #1, as shown in the diagram.
V12 V23 V24 V
V
V11
VV
V25 V26
T2 1# R
1# 1# T9
1# R1 T10
12’x20′ assembly manual
1#
page 16
Parts Required:
U1 x4 U9 x4
U3 x4
U4 x8
U10 x4
Step 14: Connect Solidifying Bars
1. Connect the U10 Bars at the ends where the holes are 5.1″ apart to one another using screw 1# as shown in diagram.
U10
1# U4 1#
U10
3.3″
5.1″
5.1″
U9
U 10
U1
U 10 U9
U1
U1 U1
U9
U 10
U 10
U9
1# x36
X2
3.3″
2. Attach Solidifying Bars ( Part U1, U9, U10) to Roof Bar or Corner Roof Bar using Iron Angle (Part U3, U4) and screws 1# as shown in the diagram.
X4
1#
Attention: If the holes on the Solidifying Bar (Part U1, U9, U10) and the hole
of the roof panel cannot be aligned, please adjust or loosen screw 1# until
the screws of the roof panel are in place.
1#
X6
U4
1#
X2
U3
U10
U10
U4
12’x20′ assembly manual
page 17
Parts Required:
x32
H3 x1
W11 x2 W12 x2 W13 x2 W14 x2 W15 x2 W16 x2 W17 x2 W18 x2
Step 15: Snap Bracket
Snap Brackets (Part Z) to roof panel edges as shown in the diagram.
(with snaps facing upwards)
X2
Z
Z
Z
Z
Z
Z
Z
Z
Z
W11
Tips:
W12
W13
W14
1. Wearing protective gloves is recommended.
2. To prevent Z-Clips (plastic brackets) from sliding off prior to assembly, apply
double-sided adhesive tape (Part H3) to the underside (bottom) edge of the
roof panels where the brackets (Part Z) are supposed to attach.
3. You can use super glue (not included) to attach the brackets to the roof panel if
the double-sided tape doesn’t work for you.
Z
Z Z Z
Z Z Z Z
W15
W16
W17
W18
12’x20′ assembly manual
page 18
Parts Required:
X21 x2 X22 x2 X23 x2 X24 x2 X25 x2 X26 x2 X27 x2 X28 x2 X29 x2 X30 x2 X31 x2
X32 x2
Step 16: Snap Bracket
Snap Brackets (Part Z, Z1, Z2) to roof panel edges as shown in the diagram.
(with snaps facing upwards)
X2
Z Z
Z Z Z Z2
Z Z Z
Z x28 Z1 x2 Z2 x2
H3 x1
X21 X22
X23
X24
X25
X26
Tips:
1. Wearing protective gloves is recommended.
2. To prevent Z-Clips (plastic brackets) from sliding off prior to assembly, apply
double-sided adhesive tape (Part H3) to the underside (bottom) edge of the
roof panels where the brackets (Part Z, Z1, Z2) are supposed to attach.
3. You can use super glue (not included) to attach the brackets to the roof panel if
the double-sided tape doesn’t work for you.
Z
Z Z
Z
Z
Z
Z
Z1
X27
X28
X29
X30
12’x20′ assembly manual
X31 X32
page 19
Overall roof assembly:
Please place the panels on the frame and assemble them from the centerline (Part N1,
N2 N1
N2) to the left and right.
X21
X22
X23
N2
X24
X25
X26
X27 X28
X29 X30 X31
X32
W18 W17 W16 W15 W14 W13 W12 W11
X32
W11 W12
W13
X30 X31 X29 X28 X27 X26
W14 W15 W16
X25 X24 X23 X22
W17 W18
X21
N1
Connect roof as below
Tip: Wearing protective gloves is recommended.
Tip: To facilitate the easy fastening of roof panels (Part W14, X26), please
use double-sided
adhesive tape (Part H3) to affix Part S onto Panel (Part W14, X26) in advance.
This will prevent Part S from sliding down during assembly.
X4
W14 , X26
Part S with adhesive tape
The back view of Panels
12’x20′ assembly manual
page 20
Parts Required:
5#
6#
7#
10#
S x160
L 28mm x100
L 45mm
x8
L 50mm
x48
L 25mm x4
10#
Step 17: Affix roof panels
using screws and Spacers (Part S) as shown in the diagram.
6#
Align all roof panels and screws
LOOSELY (DO NOT TIGHTEN
ANY SCREWS) until all the roof
panels are aligned accordingly.
THEN, TIGHTEN all screws to
secure the roof panels in place.
S
S
X4
6#
X8
X100
5#
S 5#
X48
7#
Tip:
At least two people
2+
for this step.
12’x20′ assembly manual
S 7#
page 21
Parts Required:
1#
11#
P12 x2
x6
x12
Q19 x2 Q20 x2
Step 18Assemble Net Frames
Attach net frame (Part P12, Q19, Q20) to finishing barcPart P2, Q9, Q10) using
screws (1#
11#) as
shown in the diagram.
N3 Q19
N2
Q20
N3
Upward View
N1
N1
P12 N3 Q20
N1 P12
N2
Q19
P12 N3
11#
1# 11#
N3
Q20
N2
Q19
N3
1# 11#
Perspective Q19
Q20
P12 Q19
1#
11#
11#
P12
Q20
1# 11#
Tip: The perspective drawing is for demonstrating how to assemble the final step that sets up the Net Frame (Parts P12, Q19, Q20) more effectively.
12’x20′ assembly manual
page 22
Parts Required:
Y7 x2
Y9 x2
Step 19Assemble Net and Sidewall
Install the Mosquito Net on the inner rails and the Solid Sidewalls on the
outer rails as shown in the diagram.
4#
Y7,Y9
(Not included)
(Not included)
12 ft
1
2
34
5
6
7
Y7
Y9
Y9
8 910111213141 2 3 4 5
20 ft
543
21
(Not included)
Y7
Net
20 ft
12 ft
Y7
Y9
Y7
Y7
7th
1
1
Y9
5th 5th
Y7
1
1
7th
(Not included)
(Not included)
(Not included) 12’x20′ assembly manual
page 23
Parts Required:
Step 20: When closing the Mosquito Net, refer to the steps below to align it
with the poles, as
shown in the diagram.
æ
ê
é
(Not included)
Y7,Y9
è
ç
SY
(Not included)
Y7,Y9
Y7,Y9
(Not included)
(Not included)
Y7,Y9
Care and Warranty
· Cleanse the frame components and fabric using a mild soap solution, then
rinse thoroughly. Refrain from using bleach, acid, or any other solvents on
the fabric or frame components.
· The roof, frame, bolts, and nuts are guaranteed to be free from defects in
material and workmanship for a duration of one year from the date of purchase.
The privacy curtain and mosquito netting are warranted for only 90 days. For a
detailed warranty policy, kindly refer to www.kozyard.com. Please note that
warranty terms are subject to change without prior notice.
· Regularly inspect and tighten all bolts and fasteners to ensure the optimal
performance and safety of your gazebo.
12’x20′ assembly manual
page 24
Thank you for your purchase ofKOZYARD’s gazebo.
As expert manufacturer of hardtop gazebos, Kozyard remains committed to
supporting you with parts and replacements, even beyond your warranty period.
Don’t hesitate to contact us directly if you are missing parts or need a
replacement.
66
Kozyard LLC
© Copyright 2016 – 2023 Kozyard LLC. | All Rights Reserved.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>