KZAHG1012GY5 Alexander Hardtop Gazebo Double Roof

Product Information

Specifications

• Product Name: 10’x12′ Alexander Hardtop Gazebo With Double
  Roof

• Manufacturer: Kozyard LLC

• Website: www.kozyard.com

• Version: 20231006

Warnings and Cautions

• Two or more people are required for assembly and
  disassembly.

• Do not fully tighten screws prior to complete assembly.

Pre-assembly

Tools that may be required (Not included in boxes):

• Safety glasses
• Anchor Blueprint (10’x12′)
• Recommended Minimum Anchor Block Size: 136.88 in.

Anchoring poles into concrete is strongly recommended. Ensure
the gazebo is positioned on level ground.

Prior to assembly, verify that all parts and pieces are included
to ensure an efficient installation process.

Assembly Instructions

Step 1: Set up Poles

1. Set up Poles (Part A) with Bracket (Part R2) and Stand Plates
(Part L) using screws 8# and 1# as shown in the diagram.

• Part A: Pole (Qty: 4)
• Part R2: Corner bracket (Qty: 8)
• Part L: Stand Plate (Qty: 4)
• 8# screws: Quantity: 16
• 1# screws: Quantity: 12

Reference for anchoring gazebo:

• Depth of anchor: 3 inches
• Diameter of anchor: 3/8 inches
• Anchor type: M6 x 12 (Not included)

After assembly, we strongly recommend anchoring the gazebo to
your deck or concrete as shown above. Damage resulting from wind or
improper anchoring is not covered under warranty.

FAQ

Q: How many people are required for assembly and disassembly of

the gazebo?

A: Two or more people are required for assembly and disassembly
of the gazebo.

Q: Is anchoring the gazebo into concrete necessary?

A: Yes, anchoring the gazebo into concrete is strongly
recommended to ensure stability.

Q: What should I do if any parts are missing?

A: Prior to assembly, verify that all parts and pieces are
included. If any parts are missing, please contact Kozyard LLC for
assistance.

10’x12′ Alexander Hardtop Gazebo With Double Roof
Assembly Manual
Kozyard LLC Products
www.kozyard.com
© Copyright 2016 – 2023 Kozyard LLC. | All Rights Reserved.
Version:20231006

Warnings and Cautions
· Please read and follow this assembly and operation guide to reduce the risk of personal injury and damage to your gazebo.
· Do not discard any of the packaging until you have checked that you have all the parts in place. The maximum weight capacity of this gazebo roof is 2500 pounds.
· Sidewalls and nettings should be off or in the opened position and tied to poles when winds are over 30 MPH to avoid damage.
· Some parts may have sharp edges or corners. To ensure your safety, follow basic safety precautions to reduce the risk of injury. Please note that this item contains small parts which could be swallowed by children. Keep it out of reach of children under 3 years old and pets during installation.

Two or more people are required

2+

for aseembly and disassembly.

Do not fully tighten screw prior to complete assembly.

Pre-assembly
Tools that may be required.(Not included in boxes) Note: Tools are not shown to actual size and scale.

10’x12′ Anchor Blueprint

6.77 in.

12 in.

Safetyglasses

12 in.

111.43 in. ø0.31in.

Recommended Min. Anchor Block Size

136.88 in.
Anchoring poles into concrete is strongly recommended. Ensure the gazebo is positioned on level ground.

Attention: Prior to assembly, verify that all parts and pieces are included to ensure an efficient installation process.

A x4

J1 x4

B x2 B1 x2

J2 x4 K x1

B2 x2

K1 x1

F x4 H x4 H2 x1

C x2

L x4

R2 x8

C1 x2

C2 x2

M x4

B6 x2 B61 x2 B62 x2 C6 x2 C61 x2 C62 x2 G x4 H1 x4 H3 x1

ITEM A B
B1 B2 C C1 C2 B6 B61 B62 C6
C61 C62 F G H H1 H2 H3 J1 J2
K K1 L R2 M N

N x4

DESCRIPTION

QTY

Pole

4

Beam

2

Joint Bar

2

Sidewall Track

2

Beam

2

Jointer Bar

2

Sidewall Track

2

Beam

2

Jointer Bar

2

Sidewall Track

2

Beam

2

Jointer Bar

2

Sidewall Track

2

Union Bar

4

Corner Cover

4

Joint Cover

4

Joint Cover

4

Silcone Rubber

1

Double-sided adhesive tape 1

Corner Solidifyng Bar 4

Corner Solidifyng Bar 4

Inside Roof Connector 1

Outside Roof Connector 1

Plate

4

Corner bracket

8

Corner Roof Bar

4

Roof Bar

4

Alexander 10’x12′ assembly manual

page 1

P x2 Q1 x2

P1 x2 Q x2 Q2 x2

R x8

S x104+2 T x2
T1 x2 U0 x4 U x4

U3 x4

U4 x4

V1 x2 V2 x2 V3 x2 V4 x2 V5 x2 V6 x2

W1 x2 W2 x2 W3 x2

W4 x2 W5 x2 W6 x2

ITEM P
P1 Q Q1 Q2 R S T T1 U0 U U3
U4 V1 V2 V3 V4 V5 V6 W1 W2 W3 W4 W5 W6

DESCRIPTION Finishing Bar Net Frame Finishing Bar Net Frame Net Frame Finishing End Spacer Finishing Bar Finishing Bar Solidifying Bar Solidifying Bar Iron Angle Iron Angle
Roof Panel Roof Panel Roof Panel Roof Panel Roof Panel Roof Panel Roof Panel Roof Panel Roof Panel Roof Panel Roof Panel Roof Panel

QTY 2 2 2 2
2 8 104+2 2 2 4 4 4 4 2 2 2 2 2 2 2 2 2 2 2 2

Alexander 10’x12′ assembly manual

page 2

5# x64+3

6# x8+1

X1 x2 X2 x2 X3 x2 X4 x2

M5x15

7# x28+2 8# x16+2 9# x24+2

X5 x2 X6 x2 X7 x2 X8 x2 S1 x2

S2 x2

SY x4

Y1 x2

Y2 x2 Z x56+2

Z1 x4 Z3 x4

Z2 x4 Z4 x4

4# x104+3 1# x218+4 2# x16+2 12×20+M6x12 3# x16+2

ITEM
X1
X2 X3 X4 X5 X6 X7 X8 S1 &S2
Y1 &Y2 SY Z
Z1 Z2 Z3 Z4 1# 2# 3# 4# 5# 6# 7#
8# 9# 10# 11#

DESCRIPTION
Roof Panel Roof Panel Roof Panel Roof Panel Roof Panel Roof Panel Roof Panel Roof Panel Solid Sidewall Mosquito Net Strap Bracket Bracket Bracket Bracket Bracket Screws Screws Screws Hook
Screws Screws Screws Screws Screws Screws Screws

Alexander 10’x12′ assembly manual

10# x4+1
11# x8+1
Allen key
Wrench
QTY
2 2 2 2 2 2 2 2 4 4 4 56+2 4 4 4 4 218+4 16+2 16+2 104+3 64+3 8+1 28+2 16+2 24+2 4+1 8+1
page 3

Parts Required: Step 1: Set up Poles
1. Set up Poles (Part A) with Bracket (Part R2) and Stand Plates (Part L) using screws 8# and 1# as shown in the diagram.

R2 x8 8# x16

R2 R2

1# x12

A

L x4 A x4

8# 8#
R2
A
(Inclined Plane)

1#

L

1#

L

R2
8# 8#
A
1#

Reference for anchoring gazebo:
· If the ground is concrete and its depth is over 3 inches, you can purchase 3/8″ diameter x 3″ length sleeve anchors.
· Only anchor after finishing all the assembly.

3 inches
3/8 inches

M6

X12

(Not included)

After assembly, we strongly recommend anchoring the gazebo to your deck or concrete as shown above. Damage resulting from wind or improper anchoring is not covered under warranty.

Alexander 10’x12′ assembly manual

page 4

Parts Required

C x2

F x4

C6 x2

1#

X24

Step 2: Connect the Beams

1. Connect Beams (Part C and B) into one beam using Union Bar (Part F) with screws 1# as shown in the diagram.

Short Beam Overall:

C

X2
B

F

B

B

X2
C C

B x2 B6 x2

F

1#

1#

1# 1#

2. Connect Beams (Part C6 and B6) into one beam using Union Bar (Part F) with screws 1# as shown in the diagram.

Long Beam Overall:
C6

X2
B6

F

B6

B6

X2

C6

C6

F

1#

1#

1#

1#

Alexander 10’x12′ assembly manual

page 5

Parts Required:
C1 x2 C2 x2 C61 x2 C62 x2

1# x80

Step 3: Connect Joint Bars and Tracks with Beams

10 ft overall:

C1

B1

B1 x2 B2 x2
B61 x2 B62 x2
X2

C2 C

B

B2

12 ft overall:

C61

B61

X2

C6

B6

C62

B62

1. Connect Joint Bars (Part C1 and C61), Tracks (Part C2 and C62) to Beams (Part C and C6) using screws 1# as shown in the diagram.

X2

C,C6

Tip: Do not tighten all screws on the Jointer bars (Part C1, C61, B1, B61) until the screws of the roof panels are aligned in place.
B,B6

1#

C1,C61

1#
C2,C62

1#
1#
B2,B62

2. Replicate the same steps for Joint Bars (Part B1 and B61), Tracks (Part B2 and B62), attaching them to Beams (Part B and B6) using screws 1# as shown in the diagram.

X2
B1,B61
Alexander 10’x12′ assembly manual

page 6

Parts Required

2#

3#

x16

x16

Step 4: Set up Poles and Beams

Use screws 3# first, then use screw 2# to connect Poles and

X8

Beams together as shown in the diagram.

3# 3#

A
Tip: Place parts on carpet or rug to avoid scratches during assembly

B
X2
C
A

C B

2#

X8

2#

B
C B6

Tip:

At least three people

3+

for this step.

C6
X2
C6 B A

B6

C

A

C

B6

A

B C6
A

Alexander 10’x12′ assembly manual

page 7

Parts Required: J1 x4

J2 x4

1#
x32

J1

J2

1#

1#

1#

X4
Step 5: Connect Solidifying Bars wtih Beams and Poles
Affix the frame with Corner Solidifying Bars (Parts J1, J2) using screws 1# as shown in diagram.

J1

J2

J2 J1

Diagonal 1

J1 J2

Diagonal 2

J2
Diagonal 1 = Diagonal 2

J1
Tip: Measure (DIAGONALLY) from posts to posts to assure alignment so all materials fit as planned.

Alexander 10’x12′ assembly manual

page 8

Parts Required:

G x4

H x4

9#

9#
x24
9#

G
9#
X4
Step 6: Cover the connections
1. Finish Connecting Beams using Corner Covers (Part G) and screws 9# as shown in the diagram.

H
X4 2. Affix the middle beams using Joint Cover (Part H) and screws 9# and 1# as shown in the diagram.

Alexander 10’x12′ assembly manual

page 9

Parts Required:

H2 x1

Step 7: Seal the seams
1. After finishing Step 6, apply silicone rubber to the seams to ensure they’re watertight. 2. If the screws are correctly attached through Spacer part S on the roof panels, sealing the cap
screws with silicone rubber isn’t necessary.

X4

Alexander 10’x12′ assembly manual

page 10

Parts Required:

1#

4# x104

H1 x4

x4

Step 8: Install Hooks
After finishing Hooks (Part 4#) into the tracks, then put Joint Cover (Part H1) to lock them.

4#
4#

4# 4#

4# H

Note the

amount of

hooks for

each slot as noted below:

H1 1#

X4

Put 6 Hooks in each slot of the Sidewall Track (Part C2, B2).
C2

X2 B2

X2 Put 7 Hooks in each slot of the

Sidewall Track (Part C62, B62).

C62

B62

CB
x6

x6

H1

C6 B6

x7

H1

x7

Alexander 10’x12′ assembly manual

page 11

Parts Required:

M x4

K x1

P x2 Q x2

Step 9: Set up Roof Frame

M

Q

R x4
1# x16
M

1#

P

1#

M
M K
1#

K
Upward View

1#

1#

P

Q
1. Connect the Inside Roof Connect (Part K) with the Corner Roof Bar (Part M) using screws 1#. X4

M M
1#

M
M P 1#

3. Attach Finishing

Bar (Part P and Q)

with Finish End (Part

R) using screw 1# to

R

Corner Roof Bar (Part M) as shown in

diagram.

Q

X4

2. Attach Corner Roof Bar(Part M) to main frame using screw 1# as shown in diagram.
X4

PK

M

M

MQ

Alexander 10’x12′ assembly manual

page 12

Parts Required:
Upward View

N

1#

N x4
N Q
1#

1#

1# x12
PN 1#

N Step 10: Set up Roof Bar
Attach Finishing Bar (Part P,Q) with Finish End (Part R) using screw 1# to Corner Roof Bar (Part M).

X4
1#

X4

N

1#

N

P

N

N

N N

Alexander 10’x12″ assembly manual

page 13

Parts Required:

K1 x1

1#

x2

Step 11: Connect Outside Roof Connctor
Connect Outside Roof Connector (Part K1) to Inside Roof (Part K) using screw 1# as shown in the diagram.
Upward View

1#

1#

K1

K

K1

Alexander 10’x12′ assembly manual

page 14

Parts Required:

Z X8

Z1 X4

V1

V2

V3

V4

V5

V6

Z2 X4

Step 12: Snap Brackets
Snap Bracket (Part Z, Z1, Z2) to the roof panel edges as shown in the diagram.
(with snaps facing upwards)

Z2

X2

Z1

Z

H3 x1

V1

V2

V3

V4

V5

V6

Tip:
1. Wearing protective gloves is recommended. 2. To prevent Z-Clips (plastic brackets) from sliding off prior to assembly, apply
double-sided adhesive tape (Part H3) to the underside (bottom) edge of the roof panels where the brackets (Part Z, Z1, Z2) are supposed to attach. 3. You can use super glue (not included) to attach the brackets to the roof panel if the double-sided tape doesn’t work for you.

Alexander 10’x12′ assembly manual

page 15

Parts Required: T x2

R x4

T1 x2

R

V6

T

V1

1# x8

V5

T1 V4

V3

R

V2 T

1# V2

R

V3

V4

1#

V1 R

V5

V6

1#

T1

Step 13: Assemble Roof Panels

1. Push the Roof Panels (Part V1, V2, V3, V4, V5, V6) to the upper roof as shown in the diagram. 2. Attach Finishing Bars (Part T, T1) to the upper roof with Finish End (Part R) using screws 1# as
shown in the diagram.

V1 V2

V3

V4 V5

V6

T 1#

1# R

T1

1#

Alexander 10’x12′ assembly manual

page 16

Parts Required:

U0 x4

1#

U x4

U3 x4

U4 x4

x24

Step 14: Connect Solidifying Bars
Attach Solidifying Bars (Part U0, U) to the roof bar or corner roof bar using Iron Angle (Part U3, U4) and screws 1# as shown in the diagram.

U U

U0 U0

U0 U0

U U

X4
1#

Attention: If the holes on the Solidifying Bar (Part U0, U) and the hole of the roof panel cannot be aligned, please adjust or loosen screw 1# until the screws of the roof panel are in place.
X4
U4

U3
Alexander 10’x12′ assembly manual

1#
page 17

Parts Required: Z x24
Z3 x2
Z4 x2
Step 15: Snap Brackets
Snap Bracket (Part Z, Z3, Z4) to the roof panel edges as shown in the diagram. (with snaps facing upwards)
X2
Z3 Z

H3 x1

Tip:1. Wearing protective gloves is recommended. 2. To prevent Z-Clips (plastic brackets) from sliding off prior to assembly, apply double-sided adhesive tape (Part H3) to the underside (bottom) edge of the roof panels where the brackets (Part Z, Z3, Z4) are supposed to attach. 3. You can use super glue (not included) to attach the brackets to the roof panel if the double-sided tape doesn’t work for you

Alexander 10’X12′ assembly manual

page 18

Parts Required:

Z x24 Z3 x2 Z4 x2

Step 16: Snap Brackets
Snap Bracket (Part Z, Z3, Z4) to the roof panel edges as shown in the diagram. (with snaps facing upwards)
X2
Z3 Z Z

H3 x1

Tip: 1. Wearing protective gloves is recommended. 2. To prevent Z-Clips (plastic brackets) from sliding off prior to assembly, apply
double-sided adhesive tape (Part H3) to the underside (bottom) edge of the roof panels where the brackets (Part Z, Z3, Z4) are supposed to attach.

Alexander 10’X12′ assembly manual

page 19

Overall roof assembly:
Please place the panels on the frame and assemble them from the centerline (Part N) to the left and right.

N N

X1 X2 X3 X4 X5 X6 X7
X8

W6 W5 W4
W3 W2 W1

W1

W2

W3

W4

N

W5

W6

Connect roof as below

X7 X8 X6 X5 X4 X3

X2

X1

N

Tip:
Wearing protective gloves is recommended.

Tip: To facilitate the easy fastening of roof panels (Part W3, Part X4), please use double-sided adhe-
sive tape (Part H3) to affix Part S onto Panel (Part W3, Part X4) in advance. This will prevent Part S from sliding down during assembly.
X4

Part S with adhesive tape

W3
X4

The back view of Part W3 , Part X4

Alexander 10’x12′ assembly manual

page 20

Parts Required: 10#
S
X4

S x104

5# x64

6# x8

L 28mm

L 45mm

Step 17: Affix roof panels using
screws and Spacers (Part S) as shown
in the diagram.

7#
x28 L 50mm
6#

10#
x4 L 25mm

Align all roof panels and screws LOOSELY (DO NOT TIGHTEN ANY SCREWS) until all the roof panels are aligned accordingly, THEN TIGHTEN all screws to secure the roof panels in place.

S
6#
X8

X64
5#

X28
7#

S 5#

2+
Tip: At least two people for this step.
Alexander 10’x12′ assembly manual

S
7#
page 21

Parts Required:
P1 x2

Q1 x2
Q1
Upward View

1#

11#

Q2 x2

x4

x8

Q2

P1

P1

Q2

Q1

Step 18: Assemble Net Frame
Attach Net Frames (Part P1, Q1, Q2) to Finishing Bars (Part P, Q) using screws (1#, 11#) as shown in
the diagram.

Q2

Q1

11#

1#

Perspective: Q1
Q2

11#
X2

11# P1

Q2 P1
Q1

1# 11#
X2

Tip: The perspective drawing is for demonstrating how to assemble the final step that sets up the Net Frame (Parts P1, Q1, Q2) more effectively.

Alexander 10’x12′ assembly manual

page 22

Parts Required:

S1 x2

S2 x2

Step 19: Assemble Net Sidewall
Hang the Mosquito Net on the inner rails and the Solid Sidewalls on the outer rails as shown in the diagram.

Y1 x2

Y2 x2

S1,S2 Y1,Y2

S1

Y1

Y2

S2

10ft
1

2

3

4

56

7 8 9 10 11

12ft

12 13

Curtain

12 ft

S2

S1

Y2

Y1

Net
10 ft

Y1

7th

13th

Y2

13th

6th

S1

S2

Alexander 10’x12′ assembly manual

page 23

6th 1 1
7th

Parts Required:
SY X4
Step 20: When closing the Mosquito Net, refer to the steps below to align it with the poles, as
shown in the diagram. æ

ê

é

S1,S2

Y1,Y2

è

ç

S1,S2

SY Y1,Y2

S1,S2

Y1,Y2

S1,S2

S1,S2

Y1,Y2

Care and Warranty
· Clean the frame components and fabric with a mild soap solution, then rinse thoroughly. Avoid using bleach, acid, or any other solvents on either the fabric or frame components.
· The roof, frame, bolts, and nuts come with a guarantee against defects in material and workmanship for one year from the date of purchase. However, the privacy curtain and mosquito netting are warranted for just 90 days. For a comprehensive warranty policy, please visit www.kozyard.com. Be aware that warranty terms can change without prior notification.
· For the best performance and safety of your gazebo, inspect and tighten all bolts and fasteners regularly

Alexander 10’x12′ assembly manual

page 24

As expert manufacturer of hardtop gazebos, Kozyard remains committed to supporting you with parts and replacements, even beyond your warranty period.
Don’t hesitate to contact us directly if you are missing parts or need a replacement.
66
Kozyard LLC
© Copyright 2016 – 2023 Kozyard LLC. | All Rights Reserved.

References

• Kozyard LLC Official Web Site

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>