MONODEAL MD-601 Portable CD Player User Manual
- June 5, 2024
- Monodeal
Table of Contents
PORTABLE CD PLAYER
Model: MD-601
User Manual
IMPORTANT SAFETY INSTRUCTIONS
Please read this manual carefully before using this player and keep it for
later reference.
Warning:
The player
To reduce the risk of fire or avoid the damage to the human body, please
follow the instructions below:
- Never touch the lens of the device. Always keep the disc compartment closed to prevent dust from collecting on the lens.
- If the device is unable to scan discs properly, use a standard commercially available cleaner to clean the laser optics. Other cleaning methods may damage the laser optics.
- Clean the device with a clean, damp leather cloth. Do not use any cleaning agents.
- If the player fails to work, please contact our after-sales staff in time, professional technical support staff will provide you with detailed answers.
- The player can not be used or stored in a moist environment, please keep the player away from any liquid, steam, or vapor, such as raindrops, mist, etc.
- Please do not place any liquid or metal gadgets onto the player, such as a pin or a cup of coffee.
- Please do not expose the player to the sunlight and keep it away from the fire heater. The player can not be placed in a high-temperature environment.
- All professionals with extensive electronic knowledge and maintenance experience are allowed to disassemble the player for maintenance. The replacement of spare parts must be done in strict accordance with the parameters of the circuit design.
- Please do not stick or hit the player with sharp objects.
- There are light-emitting diodes in this player, staring directly with eyes should be avoided to prevent visual impairment from being caused.
- Children under 12 years are not allowed to use the player individually.
- When charging, ensure that the Power source and the Charging voltage are DC 5V/1A. Excessive voltage input may cause machine overload damage.
Battery
If the player you purchased contains batteries, please do not disassemble
the player or charge the player with other adapters that do not meet the
electrical parameters of this product to avoid circuit failure. For your
safety, please treat the built-in high-capacity polymer lithium battery by
following the instructions below:
- Please do not remove the battery pack.
- Please do not beat or impact this player.
- Please do not make the battery short circuit or pierce it.
- Please do not place the player under high temperature which is above140 F (60 C).
- Please do not put the battery on fire.
- If the battery has been damaged, please ask a professional to replace the battery with the same specification, or contact our after-sales support for help.
Hearing protection
Listen at medium volume:
Please adjust the volume to an appropriate level. If the volume is too
high, it may damage your hearing or even cause permanent damage.
Set the volume to a low level:
We are increasing the volume slowly until a comfortable, clear sound can be
heard.
Listen to the audio within a reasonable time frame:
Long time listening, even at a reasonable volume may cause damage to your
hearing. Please use the product properly and get a rest when necessary.
Environmental protection
To protect the environment and human health, please follow local laws and
regulations on the abandonment of the package, electronic product, or battery.
Please do not put the product together with household waste.
PACKAGING & PRODUCT
What’s in the box
1 *CD player | 1*3.5 to 3.5mm AUX cable |
---|---|
1*USB to Type-C charging cable | 1 *User manual |
1–Earphones |
The CD player
Item
| Function| Item|
Function
---|---|---|---
1| Display screen| 11| A-B
2| MODE| 12| TF CARD
3| EQ| 13| DC 5V
4| Next / Fast forward| 14| Charging LED
5| Previous / Rewind| 15| Power ON / OFF
6| Stop| 16| Headphone jack 1
7| Play / Pause| 17| Headphone jack 2
8| Bluetooth| 18| Volume Konb
9| PROG| 19| OPEN
10| DIR| 20| HOLD ON / OFF
TROUBLESHOOTING
Problems
| Reasons|
Solutions
---|---|---
Can’t turn on the cd player.| The power switch is not in the ON position.|
Please toggle the power switch to the ON position.
Buttons are locked.| Please make sure the HOLD button at the back of the
player is in the OFF position.
The CD player is running out of power.| Please charge the cd player.
The player is damaged.| Please contact us or ask a professional for repairs.
Cannot read discs.| The disc is installed incorrectly.| 1. Make sure the
label side of the disc is facing up;
2. Ensure the disc is inserted fully into the place.
The disc cannot be recognized.| The player is only compatible with CD, CDR,
MP3, and HDCD formats.
The disc is dirty or damaged.|
- Make sure the disc is not heavily scratched or damaged;
- Wipe the disc gently from the center radially out to the edge with a clean & soft cloth;
- Try another new disc to check if the disc is faulty.
The loader is dirty.| Wipe the lens gently with a degreasing cotton swab.
NOTE: DO NOT TOUCH THE LENS WITH YOUR HANDS
Can’t charge the CD layer.| There is no current at the power outlet.| Make
sure the power outlet is working.
The plug is not plugged in correctly.| Make sure that the two plugs of the
power cords are connected properly.
The charger is damaged.| Replace the charger with another one matching the
specification (DC 5V/1A).
The player is damaged.| Please contact us or ask a professional for repairs.
NOTE: While charging. please make sure that the Power source
and the Charging voltage are DC 5V11A. Excessive voltage input
may cause machine overload damage.
Skip in the middle of the track.| Discs are scratched or not smooth.| Please
use a dry cloth to clean the disc, or try other discs to see it works well.
Noisy and screaming when it plays.| The usage time of the disk may be too
long, so the disk is not smooth.|
- Make sure the disc is not heavily scratched or damaged;
- Wipe the disc gently from the center radically out to the edge with a clean & soft cloth;
- Try another new disc to check if the disc is faulty.
If there is a “Jiji ” sound inside the earphone, it may be caused by scratching of the disc.| Please change to another disc, and do not use the old one again to prevent the player from being damaged.
USER GUIDE
on how to insert a disc
Push the OPEN button to the right to open the door. Insert your index
finger into the center hole of the disc and take the edge of the disc with
your thumb. Keep the side with words upward while inserting the disc into the
CD player, press the disc gently to make it steady, and make sure if the disc
has been in place. Close the disc door gently and completely, otherwise, the
player will not read the disc.
( Note: The player is only compatible with CD, CDR, MP3, HDCD formats.)
Insert TF card
After plugging a TF card into the cd player, Long-press the MODE button to
enter into TF card playback mode. NOTE: The TF card supports up to 32GB. Over
32GB cannot work with it.
Insert an earphone
Only earphone with a 3.5mm plug is compatible with this player. In order to
experience better sound quality, you can use standard earphones of an iPhone
on the player, but some earphones of cellphone may produce noise. If the
earphone cannot be supported by the player, please use the standard headphones
of this player.
l iar turn on the player
There are two ways to turn on the player:
- The power switch is located on the side. Slide it to the ON position to turn on the player.
- When the power switch is in the ON position, press the PLAY button once to turn on the player.
NOTE: When a disc is played to the end and there is no activity within 20 seconds, the player will turn off Please press the PLAY button to restart the player.
How to turn off the player
There are two ways to turn off the player:
- Press the STOP button twice to turn off the player.
- Slide the power switch to the OFF position to turn off the player.
NOTE: Please toggle the power switch to the OFF position if the player is not used for a long time.
How to charge for the player
How to Charge: This player only comes with a TYPE C charging cable. Please
use a power adapter to connect with the charging cable to charge the player.
Any 5V, 1A USB power adapter will compatible with it.
NOTE: When the battery sign is flashing on the screen, it means that you
need to charge the player. Charging Time: It will need about 3-4 hours for a
full charge. When it is charging, the LED indicator near the charging port
will light up in RED; when it’s fully charged, the indicator will turn to
GREEN.
How to connect Bluetooth devices
- Turn on your Bluetooth headphone/speaker and make sure that the Bluetooth is turned on.
- Press the Bluetooth button of the player. If the Bluetooth is off, you need to press the play button to turn on the Bluetooth.
- Select the ” BT Search ” option, then press the PLAY button, and the cd player will start searching nearby Bluetooth devices.
- Press the PLAY button to select the name of your device that needs to connect to.
- After paired successfully, press the BLUETOOTH button to return to the play interface.
OTHER FEATURES
Key lock
After playback mode and sound effects have been set up, you can toggle the
power switch to the HOLD position in order to prevent the environment, for
example, naughty children or crowded occasions from affecting the setting of
the player.
Connect to the car radio/speaker
You can use this cd player in the car via the car’s radio/speaker, using
the included 3.5mm male-to-male cable to connect your car’s 3.5mm AUX port
with the cd player’s headphones jack.
NOTE: The player ONLY works with the 3.5mm AUX port. (A USB port is NOT
supportable).
Connect to other 3.5mm audio devices
You can use this cd player to connect any other audio devices that also
have a 3.5mm audio jack, such as speakers, home theater, headphones
amplifiers, etc.
PLAY
Biglow to set up the circle mode
Each time the MODE button is pressed, the order of the tracks played will
be as follows: Repeat 1( 1 ), Repeat all (OALL), random play (RAND),
preview play (INTRO) (only 10 seconds per track will be played in this mode).
How to program the play
Press the PROG button to enter the programming mode when the play stops,
press the PREVIOUS or NEXT button to select the track you want to program, and
press PROG again to confirm the programming. Up to 30 tracks can be programmed
in this mode. After that, press the PLAY button to enter the programming play
mode. Press the STOP button directly to enter the stop mode to cancel or
reprogram.
How to Set A – B Repetition
If you want to repeat the specific part of a track when the player is
playing that part, please press the A-B button one time, the display show “A
ON”, then when it plays to the end of that part, press the A-B button once
again, the display shows “Ab ON”.After that, the player will only repeat that
specific part.
NOTE: If you want to stop repeating that part, press the A-B button once
again, the display shows “Ab OFF”, and it will play in order.
How to set up sound
How to adjust the volume
The volume knob is located on the side of the player. Rotate it to the left or
right to decrease or increase the volume. Please listen to music at an
appropriate volume to protect your ears.
How to setup EQ effect
Press the EQ button to changes the different sound effects. There are a total
of 5 sound effects: BBS, POP, JAZZ, ROCK, and CLASSIC.
FCC Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is
- Consult the dealer or an experienced radio/TV technician for help.
Caution: Any changes or modifications to this device not explicitly approved
by the manufacturer could void your authority to operate this equipment.
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions:
(1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference
that may cause undesired operation.
RF Exposure Information
The device has been evaluated to meet general RF exposure requirements. The
device can be used in portable exposure conditions without restriction.