KOZYARD KZCHG1010GY5 Caesar Hardtop Gazebo Double Roof Instruction Manual

KOZYARD KZCHG1010GY5 Caesar Hardtop Gazebo Double Roof

Product Information

Specifications:

• Product Name: 10’x10′ Caesar Hardtop Gazebo With Double Roof
• Manufacturer: Kozyard LLC
• Website: www.kozyard.com
• Version: 20231006

Warnings and Cautions:

• Two or more people are required for assembly and disassembly.
• Do not fully tighten the screw prior to complete assembly.

Pre-assembly:
Tools that may be required (Not included in boxes):

• Safety glasses
• 10’x10′ Anchor Blueprint

Note: Tools are not shown to actual size and scale. Recommended Min. Anchor Block Size: 12 in. Anchoring poles into concrete is strongly recommended. Ensure the gazebo is positioned on level ground.

Attention:
Prior to assembly, verify that all parts and pieces are included to ensure an efficient installation process.

Parts List:

Product Usage Instructions

Set up Poles
Set up Poles (Part A5) with Stand Plates (Part L5) using screws 1# as shown in the diagram.

Connect the Beams
Connect Beams (Part E5 and D5) into one beam using Union Bar (Part F5) with screws 1# as shown in the diagram.

Set up Poles and Beams
Use screws 3#L and 3# first, then use screw 2# to connect the Poles and Beams together as shown in the diagram.

FAQ

Q: Do I need to anchor the gazebo?
A: Yes, it is strongly recommended to anchor the gazebo to your deck or concrete. Damage resulting from wind or improper anchoring is not covered under warranty.

Q: Are the required tools included in the box?
A: No, the required tools such as safety glasses and the 10’x10′ Anchor Blueprint are not included in the box.

Warnings and Cautions

Please read and follow this assembly and operation guide to reduce the risk of personal injury and damage to your gazebo.

• Do not discard any of the packaging until you have checked that you have all the parts in place. The maximum weight capacity of this gazebo roof is 2000 pounds.
• Sidewalls and nettings should be off or in the opened position and tied to poles when winds are over 30 MPH to avoid damage.
• Some parts may have sharp edges or corners. To ensure your safety, follow basic safety precautions to reduce the risk of injury. Please note that this item contains small parts which could be swallowed by children. Keep it out of reach of children under 3 years old and pets during installation.

Two or more people are required for assembly and disassembly.

Do not fully tighten screw prior to complete assembly.

Pre-assembly
Tools that may be required.(Not included in boxes) Note: Tools are not shown to actual size and scale.

Anchoring poles into concrete is strongly recommended. Ensure the gazebo is positioned on level ground

Attention : Prior to assembly, verify that all parts and pieces are included to ensure an efficient installation process.

Parts Required:

Step 1: Set up Poles

Set up Poles (Part A5) with Stand Plates (Part L5) using screws 1# as shown in the diagram.

Reference for anchoring gazebo:

• If the ground is concrete and its depth is over 3 inches, you can purchase 3/8″ diameter x 3″ length sleeve anchors.
• Only anchor after finishing all the assembly.

After assembly, we strongly recommend anchoring the gazebo to your deck or concrete as shown above. Damage resulting from wind or improper anchoring is not covered under the warranty

Parts Required：

Step 2: Connect the Beams

Connect Beams (Part E5 and D5) into one beam using Union Bar (Part F5) with screws 1# as shown in the diagram.

Connected Beam Overall:

Parts Required：

Step 3: Set up Poles and Beams

Use screws 3#L and 3# first, then use screw 2# to connect Poles and Beams together as shown in diagram.

Parts Required:

Step 4: Connect Solidifying Bars with Beams and Poles

Affix the frame with Corner Solidifying Bars (Parts J5, J6) using screws 1# as shown in the diagram.

Tip :
Measure (DIAGONALLY) from posts to posts to assure alignment so all materials fit as planned.

Parts Required:

Step 5: Cover the connections

1. Finish Connecting Beams using Corner Covers (Part G5) and screws 9# as shown in the diagram.
2. Affix middle beams using JointCover (Part H5) and screws 9# as shown in diagram.

Parts Required:

Step 6: Install Hooks

After finishing Hooks (Part 4#) into the tracks, then put Joint Cover (Part H1) to lock them.

Parts Required:

Step 7: Set up Roof Frame

1. Connect the Inside Roof Connector (Part K2) with the Corner Roof Bar (Part M5) using screws 1#.
2. Attach Corner Roof Bar(Part M5) to main frame using screw 1# as shown in diagram.
3. Attach Finishing Bar (Part P) with Finish End (Part R) using screws 1# to Corner Roof Bar (Part M5) as shown in diagram.

Parts Required:

Step 8: Set up Roof Bar

1. Attach Roof Bar (Part N5) to Roof Connector (Part K) using screw 1# as shwon in the diagram.
2. Connect Roof Bar connector (Part R5) to Roof Bar (Part N5) using screw 1# as shwon in the diagram.
3. Attach Roof Bar (Part N5) to Beams using screw 1# as shwon in the diagram.

Parts Required:

Step 9: Connect Outside Roof Connctor

Connect Outside Roof Connector (Part K12) to Inside Roof (Part K2) using screw 1# as shown in the diagram.

Parts Required:

Step 10: Snap Brackets

Snap Br acket (Part Z, Z1, Z2, Z3, Z4) to the roof panel edges as shown in the diagram.

Parts Required

Step 11: Assemble Roof Panels

1. Push the Roof Panels (Part V1,V2) to upper roof as shown in the diagram.
2. Attach Finishing Bars (Part T) to upper roof with Finish End (Part R) using screws 1# as shown in the diagram.

Parts Required:

Step 12: Connect Solidifying Bars

Attach Solidifying Bars ( Part U0) to roof bar or corner roof bar using Iron Angle (Part U3, U4) and screws 1# as shown in the diagram.

Attention:
If the holes on the Solidifying Bar (Part U0) and the hole of the roof panel cannot be aligned, please adjust or loosen screw 1# until the screws of the roof panel are in place.

Overall roof assembly:

Please place the panels on the frame and assemble them from the centerline (Part N5) to the left and right.

Tips:
To facilitate the easy fastening of roof panels (Part B13), please use double- sided adhesive tape (Part H3) to affix Part S onto Panel (Part B13) in advance. This will prevent Part S from sliding down during assembly.

Parts Required

Step 13: Affix roof panels using screws and Spacers (Part S) as shown

Align all roof panels and screws LOOSELY (DO NOT TIGHTEN ANY SCREWS) until all the roof panels are aligned accordingly, THEN TIGHTEN all screws to secure the roof panels in place.

Parts Required

Step 14: Cover edge of roof

Attach F inishing bars (Part R9, R10) to Roof bar and Corner Roof bar, then put Finshih End (Part R, R1) to cover them using screws 1# as shown in diagram.

Parts Required

Step 15: Assemble Net Frame

Attach Net Frames (Part P1,Q0) to Finishing Bars (Part P) using screws (1#, 11#) as shown in the diagram.

Tip:
The perspective drawing is for demonstrating how to assemble the final step that sets up the Net Frame (Parts P1) more effectively.

Parts Required:

Step 16: Assemble Net Sidewall

Hang the Mosquito Net on the inner rails and the Solid Sidewalls on the outer rails as shown in the diagram.

Parts Required

Step 17: When closing the Mosquito Net, refer to the steps below to align it with the poles, as shown in the diagram.

Care and Warranty

• Clean the frame components and fabric with a mild soap solution, then rinse thoroughly. Avoid using bleach, acid, or any other solvents on either the fabric or frame components.
• The roof, frame, bolts, and nuts come with a guarantee against defects in material and workman-ship for one year from the date of purchase. However, the privacy curtain and mosquito netting are warranted for just 90 days. For a comprehensive warranty policy, please visit www.kozyard.com. Be aware that warranty terms can change without prior notification.
• For the best performance and safety of your gazebo, inspect and tighten all bolts and fasteners regularly

As expert manufacturer of hardtop gazebos, Kozyard remains committed to supporting you with parts and replacements, even beyond your warranty period.
Don’t hesitate to contact us directly if you are missing parts or need a replacement.

SUPPORT:
Toll free: 1-866-355-0018
www.kozyard.com
email: support@kozyard.com

SOCIAL MEDIA:
Follow us on Instagram
www.instagram.com/kozyard
KOZYARD LLC
© Copyright 2016 – 2023 Kozyard LLC. | All Rights Reserved.

References

• Kozyard LLC Official Web Site

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>