KZPHG1012 Apollo 10 ft. x 12 ft. Wood Grain Hardtop Gazebo with Mosquito

Netting

10’x12′ Apollo Hardtop Gazebo With Double Roof

Specifications

• Dimensions: 10’x12′
• Double roof design
• Manufacturer: Kozyard LLC Products
• Website: www.kozyard.com
• Version: 20231006

Warnings and Cautions

• Two or more people are required for assembly and
  disassembly.

• Do not fully tighten screws prior to complete assembly.

Pre-assembly

Before starting the assembly process, please ensure the
following:

• Tools that may be required (not included in boxes):
  • Safety glasses
  • Screwdriver
  • Wrench
  • Allen key
• Ensure the gazebo is positioned on level ground.
• Verify all parts and pieces are included to ensure an efficient
  installation process.

Assembly Instructions

Step 1: Set up Poles

1. Take Part A (Pole) and attach it to Part R2 (Bracket) and Part
   L (Stand Plate) using screws #8 and #1 as shown in the diagram
   below:

Step 2: Anchoring

After assembly, it is strongly recommended to anchor the gazebo
to your deck or concrete to prevent damage from wind. Follow the
reference diagram below for proper anchoring:

Note: Anchoring poles into concrete is strongly recommended.

FAQ

Q: Are the tools required for assembly included in the

boxes?

No, the tools required for assembly (safety glasses,
screwdriver, wrench, and allen key) are not included in the boxes.
Please ensure you have these tools before starting the assembly
process.

Q: Is the gazebo covered under warranty if it gets damaged due

to wind or improper anchoring?

No, damage resulting from wind or improper anchoring is not
covered under warranty. It is strongly recommended to properly
anchor the gazebo to prevent damage.

10’x12′ Apollo Hardtop Gazebo With Double Roof
Assembly Manual
Kozyard LLC Products
www.kozyard.com
© Copyright 2016 – 2023 Kozyard LLC. | All Rights Reserved.
Version:20231006

Warnings and Cautions
· Please read and follow this assembly and operation guide to reduce the risk of personal injury and damage to your gazebo.
· Do not discard any of the packaging until you have checked that you have all the parts in place. The maximum weight capacity of this gazebo roof is 2500 pounds.
· Sidewalls and nettings should be off or in the opened position and tied to poles when winds are over 30 MPH to avoid damage.
· Some parts may have sharp edges or corners. To ensure your safety, follow basic safety precautions to reduce the risk of injury. Please note that this item contains small parts which could be swallowed by children. Keep it out of reach of children under 3 years old and pets during installation.

Two or more people are required

2+

for aseembly and disassembly.

Do not fully tighten screw prior to complete assembly.

Pre-assembly
Tools that may be required.(Not included in boxes) Note: Tools are not shown to actual size and scale.

10’x12′ Anchor Blueprint

6.77 in.

12 in.

Safetyglasses

12 in.

111.43 in. ø0.31in.
136.88 in. Anchoring poles into concrete is strongly recommended.
Ensure the gazebo is positioned on level ground

Attn: Prior to assembly, verify all parts and and pieces are included to ensure an efficient installation process.
BOX 1

B1 x2 B2 x2 B61 x2 B62 x2 C1 x2

G x4 H1 x4 H2 x1 H3 x1

C2 x2

R x8

J1 x4

C61 x2

S x104+2

Z x56+2 Z1 x4 Z2 x4 Z4 x4 Z3 x4

C62 x2 J2 x4 M x4 N x4 Q x2 T x2 T1 x2 U0 x4 U x4

U3 x4

U4 x4

ITEM B1 B2 B61 B62 C1 C2 C61 C62 J1 J2 M N Q T T1
U0 U
Z
Z1 Z2
Z3
Z4
G H1 H2 H3 R S
U3
U4

DESCRIPTION Joint Bar Sidewall Track Jointer Bar Sidewall Track Jointer Bar Sidewall Track Jointer Bar Sidewall Track Corner Solidifying Bar Corner Solidifying Bar
Corner Roof Bar Roof Bar Finishing Bar Finishing Bar Finishing Bar Solidifying Bar Solidifying Bar
Bracket
Bracket
Bracket
Bracket
Bracket
Corner Cover Joint Cover Silcone Rubber
Double-sided adhesive tape
Finishing End Spacer
Iron Angle Iron Angle

QTY 2 2 2 2 2 2 2 2 4 4
4 4 2 2 2
4 4
56+2
4 4
4
4
4 4 1 1 8 104+2
4
4

10’x12′ assembly manual

page 1

BOX 2
M5x15

R2 x8 #8 x16+2

A x4

ITEM A R2 #8

DESCRIPTION Pole Corner bracket Screws

QTY 4 8
16+2

BOX 3
12×20+M6x12

B x2 B6 x2 C x2 C6 x2

6 x8+1 #7 x28+2 #9 x24+2 #10 x4+1

P1 x2

11 x8+1

Q2 x4

Allen key

L x4 H x4 #4 x 52+2 #1 x218+4 #2 x16+2 #3 x16+2 #5 x64+3

ITEM B B6 C C6
P1
Q2
L H #1 #2 #3 #4 #5 #6 #7 #9 #10

11

Wrench

DESCRIPTION Beam Beam Beam Beam
Net Frame
Net Frame
Plate Joint Cover Screws Screws Screws Hook Screws Screws Screws Screws Screws Screws Allen key
Wrench

QTY 2 2 2 2 2 4 4 4
218+4
16+2 16+2
52+2
64+3
8+1
28+2
24+2 4+1
8+1
1
1

10’x12′ assembly manual

page 2

BOX 4 BOX 5

K x1 K1 x1 P x2 F x4

Y1 x2

Y2 x2

ITEM K K1 P
F Y1 Y2

DESCRIPTION Inside Roof Connector Outside Roof Connector
Finishing Bar
Union Bar Mosquito Net Mosquito Net

QTY 1 1 2 4
2
2

V1 x2 V2 x2 V3 x2 V4 x2 V5 x2 V6 x2 W1 x2 W2 x2 W3 x2 W4 x2 W5 x2 W6 x2

X1 x2 X2 x2 X3 x2 X4 x2 X5 x2 X6 x2 X7 x2 X8 x2

ITEM V1 V2 V3 V4 V5 V6 W1 W2 W3 W4 W5 W6
X1 X2 X3 X4 X5 X6 X7 X8

DESCRIPTION Roof Panel Roof Panel Roof Panel Roof Panel Roof Panel Roof Panel Roof Panel Roof Panel Roof Panel Roof Panel Roof Panel Roof Panel Roof Panel Roof Panel Roof Panel Roof Panel Roof Panel Roof Panel Roof Panel Roof Panel

QTY 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2

10’x12′ assembly manual

page 3

Parts Required: Step 1: Set up Poles
Set up Poles (Part A) with Bracket (Part R2) and Stand Plates (Part L) using
screws #8 and #1 as shown in the diagram.

A x4

R2 x8 #8 x16

R2 R2

1 x12

A

L x4

8 #8

R2
A
(Inclined Plane)

1

L

1

L

R2

8 #8

A

1

Reference for anchoring gazebo:
· If the ground is concrete and its depth is over 3 inches, you can purchase 3/8″ diameter x 3″ length sleeve anchors.
· Only anchor after finishing all the assembly.

3 inches
3/8 inches

M6

X12

(Not included)

After assembly, we strongly recommend anchoring the gazebo to your deck or concrete as shown above. Damage resulting from wind or improper anchoring is not covered under warranty.

10’x12′ assembly manual

page 4

Parts Required

C x2

F x4

C6 x2

1

X24

Step 2Connect the Beams

1. Connect Beams (Part C and B) into one beam using Union Bar (Part F) with

screws 1# as shown in the diagram.

Short Beam Overall:

C

X2
B

F

B

B

X2
C C

B x2 B6 x2

F

1

1

1 #1

2. Connect Beams (Part C6 and B6) into one beam using Union Bar (Part F) with screws 1# as shown in the diagram.

Long Beam Overall:
C6

X2
B6

F

B6

B6

X2

C6

C6

F

1

1

1

1

10’x12′ assembly manual

page 5

Parts Required:

1 x80

C1 x2 C2 x2

C61 x2 C62 x2

STEP 3Connect Joint Bars and Tracks with Beams

10 ft overall:

C1

B1

B1 x2 B2 x2
B61 x2 B62 x2
X2

C2 C

B

B2

12 ft overall:

C61

B61

X2

C6

B6

C62

B62

1. Connect Joint Bars (part C1,C61) and Tracks (Part C2,C62) to Beams (Part C ,C6) using #1 screws as shown in the diagram.

C,C6
C1,C61

Tip: Do not tighten all screws on the Jointer bars (Part C1, C61, B1, B61) until the screws of the roof panels are aligned in place.
B,B6
B1,B61

1 #1

C2,C62
X2

1 #1

B2,B62

2. Replicate the same steps for Joint Bars (Part B1 and B61), Tracks (Part B2 and B62), attaching them to Beams (Part B and B6) using screws #1 as shown in the diagram.

X2

Tip:

Place parts on carpet or rug to

avoid scratches during assembly.

10’x12′ assembly manual

page 6

Parts Required

2

3

x16

x16

STEP 4: Set up Poles and Beams
Use screws #3 first, then use screw #2 to connect Poles and Beams together as shown in the diagram.

A
Tip: Place parts on carpet or rug to avoid scratches during assembly.

B
X2
C
A

3 #3

X8

C

2

B

2

B
C B6

Tip:

3 people suggested for

3+

this step.

C6
X2
C6 B A

X8

B6

C

A

C

B6

A

B C6
A

10’x12′ assembly manual

page 7

Parts Required: J1 x4

J2 x4

1

x32

STEP 5: Connect Solidifying Bars with Beams and Poles
Affix the frame with Corner Solidifying Bars (Parts J1, J2) using #1 screws as shown in the diagram.

J1

J2

1

1

1

X4

J2 J1

J1

J2

Diagonal 1

J1 J2

Diagonal 2

J2
Diagonal 1 = Diagonal 2

J1
Tip: Measure (DIAGONALLY) from posts to posts to assure alignment so all materials fit as planned.

10’x12′ assembly manual

page 8

Parts Required: G x4
STEP 6: Cover the connections
1. Finish Connecting Beams using Corner Covers (Part G) and #9 screws as shown in diagram.

9

9

H x4

x24

2. Affix middle beams using Joint Covers (Part H) with #9 screws as shown in diagram.

9

G

9

X4

H
X4

10’x12′ assembly manual

page 9

Parts Required:

H2 x1

STEP 7: Seal seams
1. After finishing Step 6, apply silicone rubber to the seams to ensure they’re watertight. 2. If the screws are correctly attached through Spacer part S on the roof panels, sealing the cap
screws with silicone rubber isn’t necessary.

X4

10’x12′ assembly manual

page 10

Parts Required:

1

4 x52

H1 x4

x4

STEP 8: Install Hooks
After finishing Hooks (Part #4) into the tracks, then put Joint Cover (Part H1) to lock them.

4

4

4 #4

4 H

Note the

amount of hooks for each slot

H1 #1

as noted

X4

below:

Put 6 Hooks into each slot of
Sidewall Track (part C2
B2).
C2

X2 B2

Put 7 Hooks into each slot of X2

Sidewall Track (part C62, B62).

C62

B62

CB
x6

x6

H1

C6 B6

x7

H1

x7

10’x12′ assembly manual

page 11

Parts Required:

Step 9: Set up Corner Roof Bar
1. Connect the inside Roof Connector (Part K)
with the Corner Roof Bar (Part M) using #1 screws.

M

K

M

1

M

M
X4

M x4

1 x12

K x1
2. Attach Corner Roof Bar (Part M) to
Poles (Part A ) using #1 screws as shown in diagram.
2
M

1 A

X4

M

1

M

1

1

K

1

M

Upward View

M

K

M

M
2

2
M
2

2M

10’x12′ assembly manual

page 12

Parts Required:
N x4
Step 10: Set up Roof Bar
1. Connect Roof Bar (Part N) to Inside Roof Connector (Part K)using #1 screws as shown in diagram.

1

1 x12

2. Attach Roof Bar (Part N) to Beams using #1 screws as shown in diagram.

1

N

2

X4

1

N
K
Upward View
N N

N

1

1

N

X4

1

N

N

2

N

2

2

2

10’x12′ assembly manual

page 13

Parts Required:

P x2

Q x2

R x4

1 x4

Step 11: Set up Finishing Bar
Attach Finishing Bar (Part P, Q) with Finish End (Part R) using #1 screws to Corner Roof Bar (Part M) as shown in the diagram.

M
P
X4

Q

P

K Q
Upward View

P

Q

1 Q

R
P

10’x12′ assembly manual

page 14

Parts Required:

Z X8

Z1 X4

V1

V2

V3

V4

V5

V6

STEP 12:Snap Brackets
Snap Bracket (Part Z, Z1, Z2) to roof panel edges as shown in the diagram. (with snaps facing upwards)

Z2 X4

Z2

X2

Z1

Z

H3 x1

V1

V2

V3

V4

V5

V6

Tips:
1. Wearing protective gloves is recommended. 2. To prevent Z-Clips (plastic brackets) from sliding off prior to assembly, apply
double-sided adhesive tape (Part H3) to the underside (bottom) edge of the roof panels where the brackets (Part Z, Z1, Z2) are supposed to attach. 3. You can use super glue (not included) to attach the brackets to the roof panel if the double-sided tape doesn’t work for you.

10’x12′ assembly manual

page 15

Parts Required: T x2

1 x8

R x4

T1 x2

STEP 13: Assemble Roof Panels
1. Insert Roof Panels (Part v1, v2, v3, v4, v5, v6) to upper roof as shown in diagram. 2. Attach Finishing Bars (Part T, T1) to upper roof with Finish End (Part R) using #1 screws as shown
in diagram.

V6 R

V5 T1

V4

V3

R

T T

V1 V2

1 V2

R V3

1

V4 T1

V5 #1

V1
R V6

V1 V2

V3

V4 V5

V6

T #1

1 #1 R T1

10’x12′ assembly manual

page 16

Parts Required:

K1 x1

1

x2

STEP 14: Connect Outside Roof Connector
Connect Outside Roof Connector (Part K1) to Inside Roof (Part K) using #1 screws as shown in the diagram.

Upward View

1

1

K K1

10’x12′ assembly manual

page 17

Parts Required:

U0 x4

1

U x4

U3 x4

U4 x4

x24

STEP 15: Connect Solidifying Bars
Attach Solidifying Bars ( Part U0,U) to roof bar or corner roof bar using Iron Angle (Part U3, U4) and #1 screws as shown in the diagram.

U U
U0 U0

U0 U0

U U

X4

1

NOTE:
If the holes on Solidifying Bar (part U0, U) and the hole of the roof panel cannot be aligned, adjust or loosen #1 screws until the screws of the roof panel fall in place.
X4

1

U3
10’x12′ assembly manual

U4
page 18

Parts Required:
STEP 16Snap Brackets
(with snaps facing upwards)
X2
Z3 Z

Z x24 Z3 x2 Z4 x2

H3 x1

Tips:
1. Wearing protective gloves is recommended. 2. To prevent Z-Clips (plastic brackets) from sliding off prior to assembly, apply
double-sided adhesive tape (Part H3) to the underside (bottom) edge of the roof panels where the brackets (Part Z, Z3, Z4) are supposed to attach. 3. You can use super glue (not included) to attach the brackets to the roof panel if the double-sided tape doesn’t work for you

10’X12′ assembly manual

page 19

Parts Required:

Z x24 Z3 x2 Z4 x2

STEP 17Snap Brackets
Snap Bracket (Part Z, Z3, Z4) to the roof panel edges as shown in the diagram.
(with snaps facing upwards)
X2

Z3 Z Z

H3 x1

1. Wearing protective gloves is recommended. 2. To prevent Z-Clips (plastic brackets) from sliding off prior to assembly, apply
double-sided adhesive tape (Part H3) to the underside (bottom) edge of the roof panels where the brackets (Part Z, Z3, Z4) are supposed to attach. 3. You can use super glue (not included) to attach the brackets to the roof panel if the double-sided tape doesn’t work for you

10’X12′ assembly manual

page 20

Overall roof assembly:
Please place the panels on the frame and assemble them from the centerline (Part N) to the left and right.

N N

X1 X2 X3 X4 X5 X6 X7
X8

W6 W5 W4

W3 W2 W1

W1

W2

W3

W4

N

W5

W6

Connect roof as pictured

X7 X8 X6 X5 X4 X3

X2

X1

N

Tip:
Wearing protective gloves is recommended.

Tips: To facilitate the easy fastening of roof panels (Part W3, Part X4), please use double-sided adhe-
sive tape (Part H3) to affix Part S onto Panel (Part W3, Part X4) in advance. This will prevent Part S from sliding down during assembly.
X4

Part S with adhesive tape

W3
X4

The back view of Part W3 , Part X4

10’x12′ assembly manual

page 21

Parts Required: #10
S
X4

S x104

5 x64

6 x8

L 28mm

L 45mm

STEP 18

Affix roof panels using screws and Spacers (Part S) as shown in diagram.

Align all roof panels and screws LOOSELY (DO NOT TIGHTEN ANY SCREWS) until all the roof panels are aligned accordingly, THEN TIGHTEN all screws to secure the roof panels in place.

7

x28 L 50mm

6

S

10

x4 L 25mm

X8

X64

5 S

2+
Tips: At least two people for this step.
10’x12′ assembly manual

X28

7

S
page 22

Parts Required:
P1 x2

Q2 x4

1 x4

11 x8

STEP 19Assemble Net Frame
Attach Net Frames (Part P1,Q2) to Finishing Bars Part P, Q) using #1 & #11 screws as shown in diagram.

Q2

Q2
X2

P1

X2

11

1

11

11

1 #11

Q2

Q2

Upward View

P1

Q2

Perspective:

Q2

P1

Q2

Q2 P1 Q2

P1 Q2

Tips:
The perspective drawing is for demonstrating how to assemble the final step that sets up the Net Frame (Parts P1, Q2) more effectively.

10’x12′ assembly manual

page 23

Parts Required:

Y1 x2

Y2 x2

STEP 20Assemble Mosquito Net

Install the Mosquito Net on the inner rails and the Solid Sidewalls on the outer rails as shown in the diagram.

4 Y1,Y2

Y1

Y2

10ft

1 234 56

7 8 9 10111213

12ft

NET

12 ft
Y2 Y1

1th 6th

7th

13th

Y1

1th

10 ft

6th

13th

7th

Y2

The privacy curtain is not included, but available for separate purchase. Visit kozyard.com and search for KZAHG1012SW to buy it.

S1 x2

S2 x2

10’x12′ assembly manual

page 24

Parts Required:
STEP 21 When closing the Mosquito Net, refer to the steps below to align it with the poles, as shown in the diagram. æ

é

è

Y1,Y2 ç

Y1,Y2

Y1,Y2

Y1,Y2

Care and Warranty

· Clean the frame components and fabric with a mild soap solution, then rinse thoroughly. Avoid using bleach, acid, or any other solvents on either the fabric or frame components.
· The roof, frame, bolts, and nuts come with a guarantee against defects in material and workmanship for one year from the date of purchase. However, the privacy curtain and mosquito netting are warranted for just 90 days. For a comprehensive warranty policy, please visit www.kozyard.com. Be aware that warranty terms can change without prior notification.
· For the best performance and safety of your gazebo, inspect and tighten all bolts and fasteners regularly

10’x12′ assembly manual

page 25

As expert manufacturer of hardtop gazebos, Kozyard remains committed to supporting you with parts and replacements, even beyond your warranty period.
Don’t hesitate to contact us directly if you are missing parts or need a replacement.
66
Kozyard LLC
© Copyright 2016 – 2023 Kozyard LLC. | All Rights Reserved.

References

• Kozyard LLC Official Web Site

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>