KOZYARD KZAHG1220GRA Alexander 12 ft. x 20 ft. Gray Hardtop Gazebo Instruction Manual

: June 16, 2024
: KOZYARD

KZAHG1220GRA Alexander 12 ft. x 20 ft. Gray Hardtop Gazebo

12’x20′ Alexander Hardtop Gazebo With Double Roof

Specifications:

Product Name: 12’x20′ Alexander Hardtop Gazebo With Double
Roof
Manufacturer: Kozyard LLC Products
Website: www.kozyard.com
Version: 20231006

Warnings and Cautions:

Two or more people are required for assembly and
disassembly.

Pre-assembly:

Tools that may be required (not included in boxes):

Safety glasses
Recommended Min. Anchor Block Size: 6.77 in x 12 in x 12
in

Note: Tools are not shown to actual size and scale. Do not fully
tighten screw prior to complete assembly.

Attention:

Prior to assembly, verify that all parts and pieces are included
to ensure an efficient installation process.

Assembly Instructions:

Step 1: Preparing the Ground

Ensure the gazebo is positioned on level ground.

Step 2: Anchoring Poles

Anchoring poles into concrete is strongly recommended. Follow
the anchor blueprint provided in the manual for proper placement
and installation.

Step 3: Assembling the Frame

Refer to the assembly manual for detailed instructions on
assembling the frame. Use the provided poles, beams, jointer bars,
sidewall tracks, and other components to assemble the frame
according to the diagram.

Step 4: Installing the Roof

Attach the roof panels to the assembled frame using the roof
connectors. Follow the instructions on how to properly install the
roof panels.

Step 5: Finishing and Solidifying

Install the finishing bars, corner solidifying bars, joint
covers, corner covers, and other finishing components to complete
the gazebo assembly. Use the provided screws, brackets, and
adhesive tape to secure the components in place.

Step 6: Attaching the Net Frame and Mosquito Net

If included in the product, attach the net frame and mosquito
net to the gazebo according to the instructions provided in the
manual.

FAQ:

Q: How many people are required for assembly?

A: Two or more people are required for assembly and
disassembly.

Q: Is anchoring into concrete necessary?

A: Anchoring poles into concrete is strongly recommended for
stability and safety.

Q: Are all parts and pieces included in the package?

A: Prior to assembly, verify that all parts and pieces are
included to ensure an efficient installation process.

12’x20′ Alexander Hardtop Gazebo With Double Roof
Assembly Manual
Kozyard LLC Products
www.kozyard.com
© Copyright 2016 – 2023 Kozyard LLC. | All Rights Reserved.
Version:20231006

Warnings and Cautions
· Please read and follow this assembly and operation guide to reduce the risk of personal injury and damage to your gazebo.
· Do not discard any of the packaging until you have checked that you have all the parts in place. The maximum weight capacity of this gazebo roof is 2500 pounds.
· Sidewalls and nettings should be off or in the opened position and tied to poles when winds are over 30 MPH to avoid damage.
· Some parts may have sharp edges or corners. To ensure your safety, follow basic safety precautions to reduce the risk of injury. Please note that this item contains small parts which could be swallowed by children. Keep it out of reach of children under 3 years old and pets during installation.

Two or more people are required

2+

for aseembly and disassembly.

Pre-assembly
Tools that may be required.(Not included in boxes) Note: Tools are not shown to actual size and scale.

Do not fully tighten screw prior to complete assembly.

6.77 in

12×20′ ANCHOR BLUEPRINT

Safetyglasses
12 in.

12 in.

136.88 in. ø0 .31 in.

Recommended Min. Anchor Block Size
136.53 in.

111.85 in.

Anchoring poles into concrete is strongly recommended. Ensure the gazebo is positioned on level ground

Attention: Prior to assembly, verify that all parts and pieces are included to ensure an efficient installation process.
A x4

K10 x1

E21L x2 E22L x2
F x6 H1 x6
J1 x4 L x4

A1 x2

K20 x1

B6 x4

M3=M1+M2

M1 x4

M2 x4

B61 x2 B62 x4

N1 x2 N2 x2

B21 x2

N3 x4

C6 x4

C61 x2

C62 x4 C21 x2

E21R x2 E22R x2

E2 x2

G x4

H x6

H2 x1

H3 x1 J2 x4 L1 x2

ITEM DESCRIPTION

QTY

A Pole

4

A1 Pole

2

B6 Beam

4

B61 Jointer Bar

2

B62 Sidewall Track

4

B21 Jointer Bar

2

C6 Beam

4

C61 Jointer Bar

2

C62 Sidewall Track

4

C21 Jointer Bar

2

E2 Beam

2

E21L Jointer Bar

2

E21R Jointer Bar

2

E22L Sidewall Track

2

E22R Sidewall Track

2

F Union Bar

6

G Corner Cover

4

H Joint Cover

6

H1 Joint Cover

6

H2 Silcone Rubber

1

H3 Double-sided adhesive tape

1

J1 Corner Solidifyng Bar

4

J2 Corner Solidifyng Bar

4

K10 Inside Roof Connector

1

K20 Outside Roof Connector 1

L

Plate

4

L1 Plate

2

M1 Short Corner Roof Bar

4

M2 Corner Roof Bar

4

N1 Roof Bar

2

N2 Roof Bar

2

N3 Roof Bar

4

Alexander 12’x20′ assembly manual

page 1

P2 x2

P12 x2 Q9 x2 Q10 x2 Q19 x2 Q20 x2

W11 x2 W12 x2 W13 x2 W14 x2

R x8

R1 x2

S x160+3 T2 x2 T9 x2 T10 x2 U1 x4 U9 x4 U10 x4

U3 x4

U4 x8

V11 x2 V12 x2

V23 x2 V24 x2 V x8

V25 x2 V26 x2

W15 x2 W16 x2 W17 x2 W18 x2

ITEM
P2 P12 Q9 Q10 Q19 Q20 R
R1
S T2 T9
T10 U1 U3 U4 U9 U10 V11 V12 V23
V24 V V25 V26 W11 W12 W13 W14 W15 W16 W17 W18

DESCRIPTION Finishing Bar Net Frame Finishing Bar Finishing Bar Net Frame Net Frame Finishing End
Finishing End Spacer Finishing Bar Finishing Bar Finishing Bar Solidifying Bar Iron Angle Iron Angle Solidifying Bar Solidifying Bar Roof Panel Roof Panel Roof Panel Roof Panel Roof Panel Roof Panel Roof Panel Roof Panel Roof Panel Roof Panel Roof Panel
Roof Panel Roof Panel Roof Panel
Roof Panel

QTY 2
2 2 2 2 2 8 2 160+3 2 2 2
4 4 8 4 4 2 2 2 2 8
2 2 2 2 2 2 2 2 2 2

Alexander 12’x20′ assembly manual

page 2

6# x8+1 7# x48+2

X21 x2 X22 x2 X23 x2 X24 x2 X25 x2 X26 x2

9# x28+2 10# x4+1 11# x16+4

X27 x2 X28 x2 X29 x2 X30 x2 X31 x2 X32 x2

6-9*1.5

S7 x4 Y7 x4 SY x6 Z1 x6 Z3 x2
12×20+M6x12

S9 x2
Y9 x2 Z x72+2
Z2 x6 Z4 x2
4# x152+2 1# x331+5 2# x28+2 3# x16+2 5# x100+2

ITEM DESCRIPTION
X21 Roof Panel X22 Roof Panel X23 Roof Panel X24 Roof Panel X25 Roof Panel X26 Roof Panel X27 Roof Panel X28 Roof Panel X29 Roof Panel X30 Roof Panel X31 Roof Panel X32 Roof Panel S7/S9 Solid Sidewall Y7/Y9 Mosquito Net
SY Strap Z Bracket Z1 Bracket Z2 Bracket Z3 Bracket Z4 Bracket 1# Screws
2# Screws 3# Screws 4# Hook 5# Screws 6# Screws 7# Screws 9# Screws 10# Screws
11# Screws
12# Washer

Alexander 12’x20′ assembly manual

12# x12+2
Allen key
Wrench
QTY 2 2 2 2 2 2 2 2 2 2 2 2 6 6 6
72+2 6 6 2 2
331+5 28+2 16+2 152+2 100+2 8+1 48+2 28+2 4+1 16+4 12+2
page 3

Parts Required: Step 1: Set up Poles
Set up Poles (Part A,A1) with Stand Plates (Part L, L1) using screws 1# as shown in the diagram.

X4
A

1#

A

1#

A x4

L

L x4 1# x12
A1 x2

L
A1 1#
A1 1#

Reference for anchoring gazebo:

· If the ground is concrete and

its depth is over 3 inches,

you can purchase 3/8″ diam-

eter x 3″ length sleeve

1#

anchors.

· Only anchor after finishing all

the assembly.

1#
M6
L1
X2

3 inches
3/8 inches
(Not included)

X12

L1 x2
1# x8

After assembly, we strongly recommend anchoring the

L1

gazebo to your deck or concrete as shown above.

Damage resulting from wind or improper anchoring is

not covered under warranty.

Alexander 12’x20′ assembly manual

page 4

Parts Required:

C6 x4

F x6

B6 x4

1#

E2 x2

x36

Step 2: Connect the Beams
1. Connect (Part C6,B6) into one beam using Union bar (Part F) with screws 1# as shown in the diagram.

Short Beam Overall:
C6

B6

X2

F

B6

X2

C6

F 1#

1# 1#
1#

2. Connect (Part C6, E2, B6) into one beam using Union Bar (Part F) with screws 1#

as shown in the diagram.

X2
Long Beam Overall:

C6

E2

B6

F
X2
C6 F
1#

F
E2
1#

B6 1# 1#
Tip:

Alexander 12’x20′ assembly manual

page 5

Parts Required:
C61 x2 C62 x2
C21 x2

E21L x2

E21R x2

C62 x2

1# x108

Step 3: Connect Joint Bars with Beams

12 ft overall:

C61

B61

B61 x2 B62 x2
B21 x2
B62 x2

20 ft overall: C21

C62 C6
E21L

B62 B6

E21R

B21

C6

C62

B6

1#

E2

B62 B6

Tip: Do not tighten all screws on Jointer Bars (Part B61,C61,B21,C21,E21R,E21L), until the screws of the roof panels be aligned in place.

C6

1#

1#
B62

X2 B61,B21

1. Connect Joint Bars (Part B61,B21) and Tracks (Part B62) to Beams (Part B6) using screws 1# as shown in diagram.

X2 C61,C21

1#
C62

2. Replicate the same steps for Joint Bars (Part C61,C21) and Tracks (Part C62) attaching them to Beams (Part C6) using screws 1# as shown in diagram.

3. Connect Joint Bars (Part E21L,E21R) to Beams (Part E2) using screws 1# as show in diagram.

E2

X2

1#

1# 1# 1# E21R

1#

1#
E21L 1# 1# 1#

Tip:

Alexander 12’x20′ assembly manual

page 6

Parts Required

1#

2#

x12

x28

3#

E22L x2

x16 E22R x2

Step 4: Set up Poles and Beams

Use screws 3# first, then screw 2# to connect Poles and Beams together as shown in diagram.

A
Tip: Place parts on carpet or rug to avoid scratches during assembly. Tip: At least three people for 3+ this step.

B6
X2
C6
A
C6

B6

3# 3#

X8

2#

X8

2#

B6

C6

E2

C6

B6 X2

E2

X2

2#

A1

2#

C6 B6

E2

C6 B6
A

A
A1 B6
C6

A

B6 C6 E2
A

2. Connect Joint Bars (Part E22L,E22R) to Beam (Part E2) using screws 1# as shown in diagram.

E2

X2

A1

1#

E22L

1#

A1

E22R

Alexander 12’x 20′ assembly manual

page 7

Parts Required:
J1 x4

1#

J2 x4

x32

J1

J2

1#

X4
Step 5: Connect Solidifying Bars with Beams and Poles
Affix the frame with Corner Solidifying Bars (Part J1,J2) using screws 1# as shown in the diagram.
J1 J2

J2 J1

Diagonal 1

J1 J2

Diagonal 2

J2
Diagonal 1 = Diagonal 2

J1
Tip: Measure (DIAGONALLY) from posts to posts to assure alignment so all materials fit as planned.

Alexander 12’x20′ assembly manual

page 8

Parts Required:
G x4

9#

H x6

x28

Step 6: Cover the connections

9#

1. Finish Connecting Beams using Corner Covers (Part G) and screws 9# as shown in

9#

the diagram.

G

X4

9#

X6

2. Affix the middle beams using Joint Cover (Part H) and screws 9# as shown in the diagram.
Alexander 12’x20′ assembly manual

9#
H
page 9

Parts Required:
H2 x1
Step 7: Seal the seams
1. After finishing Step 6, apply silicone rubber to the seams to ensure they’re watertight. 2. If the screws are correctly attached through Spacer part S on the roof panels, sealing the cap
screws with silicone rubber isn’t necessary.
X6

Alexander 12’x20′ assembly manual

page 10

Parts Required:

4#

1#

x152

H1 x6

x6

Step 8: Install Hooks

After finishing Hooks (Part 4#) into the

tracks, then put Joint Cover (Part H1) to

lock them.

4#
4#

X6
4#

Note the amount of hooks for

4#

each slot as noted below:

H1 1#

7 Put hooks to each slot of Sidewall Track (Part C62 , Part B62) for 12 ft side.

X2

4# x7

C62

C6

B6

x7

H1

x7

B62 x7

Put 7 hooks to each slot of Sidewall Track Part C62 and 5 hooks to each slot Sidewall track Part E22L for 20 ft side. X2

4#

C62

x7

C6 H1

E2 x5

E22L x5

Put 5 hooks to each slot of Sidewall Track Part E22R and 7 hooks to each slot Sidewall Track Part B62 for 20 ft side. X2

4#

E22R

E2

x5

B6

H1

x7

Alexander 12’x20′ assembly manual

B62

x7
page 11

Parts Required: 12#

x12

M2 x4

M1 x4

1#

x12

Step 9: Connect Corner Roof Bar “M3”
Connect Short Corner Roof Bar (Part M1) with Long Corner Roof Bar (Part M2) using screws 1# and washer 12#.

Tip: The combination will be called “Part M3″ in following steps.

M2

M1

1# 12#

X4

M3=M1+M2 M1

M2

1# 12#

Tip:

Alexander 12’x20′ assembly manual

page 12

Parts Required:
1#
x36

M3 x4 K10 x1

N1 x2 N2 x2 N3 x4

Step 10: Set up roof frame

M3 N3
1#

hole

N2
1#

M3 N3
1#

hole

N1
1#

1# 1#
Upward View

N3 M3

K10
N2
hole

1#

N1

1#

N3 M3

M3 N3 1# 1#

M3 1#

N2

1#

N3

1#

N1

1# N3
M3 X2

A

X4

A1

X2

1. Connect the inside roof connector (Part K10) with the conner roof barcPart M3) and roof bar(Part N1,N2,N3) using
screws 1# as shown in diagram.
M3

N3 N2 N3

N1 M3

X4

N1

1#

M3
N1

Tip:

At least two people

2+

for this step.

N3 M3

N3 N2

X2

2. Attach corner roof bar (Part M3)

and roof bars (Part N1, N2, N3) to

the main frame using screw 1# as

shown in the diagram.

Alexander 12’x20′ assembly manual

page 13

Parts Required:
P2 x2

M3

N3 Q9

N2

Q9 x2 Q10 x2
Q10

R x4
N3

1#
x6
M3

N1
P2

Upward View

P2
N1

Q 10

Q9

M3
N3

N2

N3

M3

N2

1# R

P2

Q10

X4
Step 11: Set up Roof Bar
1. Attach the finishing bar (Part P2, Q9, Q10) with the finishing end (Part R) using screw 1# to the corner roof bar (Part M3) as shown in the diagram.

Q 10
Q9 X2 1#
2. Affix the Finishing Bar (Part Q9, Q10) to the roof bars (Part N2, N3) using screw 1# as shown in the diagram.
M3

P2
N1

Q10

Q9

N3

N2

N3

M3

Alexander 12’x20′ assembly manual

page 14

Parts Required:

1#

K20 x1

x5

Upward View

K10 K20

1#

Step 12: Connect Outside Roof Connctor
Connect the Outside Roof Connector (Part K20) to the Inside Roof Connector (Part K10) using screw 1#, as shown in the diagram.
K 20

Alexander 12’x20′ assembly manual

page 15

Parts Required:

Z x12 Z1 x4

Z3 x2

V11 x2 V12 x2

V23 x2 V24 x2

V x8

V25 x2 V26 x2

Z2 x4 Z4 x2

Step 13: Snap Bracket
Snap Bracket (Part Z, Z1, Z2,Z3,Z4) to the roof panel edges as shown in the diagram.
(with snaps facing upwards)

X2

Z1

Z2

H3 x1

Z

Z2

Z Z1

V11

V12

Z

Z4

V23

V24

V

Z

Z3

V

V25

V26

Tips:
1. Wearing protective gloves is recommended. 2. To prevent Z-Clips (plastic brackets) from sliding off prior to assembly, apply
double-sided adhesive tape (Part H3) to the underside (bottom) edge of the roof panels where the brackets (Part Z, Z1, Z2, Z3, Z4) are supposed to attach. 3. You can use super glue (not included) to attach the brackets to the roof panel if the double-sided tape doesn’t work for you.

Alexander 12’x20′ assembly manual

page 16

Parts Required:
T2 x2
R V26 V25 T2 V11

1#

T9 x2

R x4

x12

T10 x2

R1 x2

Upward View

T10 V

V

T9 V

V24 V23 R

V12 T2

1#

V12

V11

R

V23 V24

V

R

V

1#

V25 V26

T9
1#
Step 14: Assemble Roof Panel

R1 1#

T10
1# X2

1. Push the Roof Panels (Part V11, V12, V23, V24, V, V, V25, V26) up to the upper roof as shown in the diagram.
2. Attach Finishing Bars (Part T2, T9, T10) to the upper roof with Finish End (Part R) using screws #1, as shown in the diagram.

V12 V23 V24 V

V

V11

VV

V25 V26

T2 1# R

1# 1# T9

1# R1 T10

Alexander 12’x20′ assembly manual

1#
page 17

Parts Required:

U1 x4 U9 x4

U3 x4

U4 x8

U10 x4

Step 15: Connect Solidifying Bars

1. Connect the U10 Bars at the ends where the holes are 5.1″ apart to one another

using screw 1# as shown in diagram.

U10

1# U4 1#

U10

3.3″

5.1″

U9

U 10

U1

U 10 U9

U1

U1 U1

U9

U 10

U9

1# x36
X2
3.3”

2. Attach Solidifying Bars ( Part U1, U9, U10) to Roof Bar or Corner Roof Bar using Iron Angle (Part U3, U4) and screws 1# as shown in the diagram.

X4

1#

Attention: If the holes on the Solidifying Bar (Part U1, U9, U10) and the hole of the roof panel cannot be aligned, please adjust or loosen screw 1# until the screws of the roof panel are in place.
1#
X6

U4

1#

X2

U3

U10

U4

Alexander 12’x20′ assembly manual

page 18

Parts Required:

x32

H3 x1

W11 x2 W12 x2 W13 x2 W14 x2 W15 x2 W16 x2 W17 x2 W18 x2

Step 16: Snap Bracket

Snap Brackets (Part Z) to roof panel edges as shown in the diagram.

(with snaps facing upwards)

X2

Z

Z
Z Z
Z

Z

W11
Tips:

W12

W13

W14

1. Wearing protective gloves is recommended.

2. To prevent Z-Clips (plastic brackets) from sliding off prior to assembly, apply

double-sided adhesive tape (Part H3) to the underside (bottom) edge of the

roof panels where the brackets (Part Z) are supposed to attach.

3. You can use super glue (not included) to attach the brackets to the roof panel if

the double-sided tape doesn’t work for you.

Z

Z Z Z

Z Z Z Z

W15

W16

W17

W18

Alexander 12’x20′ assembly manual

page 19

Parts Required:

X21 x2 X22 x2 X23 x2 X24 x2 X25 x2 X26 x2 X27 x2 X28 x2 X29 x2 X30 x2 X31 x2 X32 x2
Step 17: Snap Bracket
Snap Brackets (Part Z, Z1, Z2) to roof panel edges as shown in the diagram. (with snaps facing upwards)
X2

Z Z
Z Z Z Z2

Z Z Z

Z x28 Z1 x2 Z2 x2

H3 x1

X21 X22

X23

X24

X25

X26

Tips:

1. Wearing protective gloves is recommended.

2. To prevent Z-Clips (plastic brackets) from sliding off prior to assembly, apply

double-sided adhesive tape (Part H3) to the underside (bottom) edge of the

roof panels where the brackets (Part Z, Z1, Z2) are supposed to attach.

3. You can use super glue (not included) to attach the brackets to the roof panel if

the double-sided tape doesn’t work for you.

Z

Z Z

Z

Z1

X27

X28

X29

X30

Alexander 12’x20′ assembly manual

X31 X32
page 20

Overall roof assembly:

Please place the panels on the frame and assemble them from the centerline (Part N1,

N2 N1

N2) to the left and right.

X21

X22

X23

N2

X24

X25

X26

X27

X28

X29

X30

X31

X32

W18 W17 W16 W15 W14 W13 W12 W11
X32

W11 W12

W13

X30 X31 X29 X28 X27 X26

W14 W15 W16

X25 X24 X23 X22

W17 W18

X21

N1

Connect roof as below

Tip: Wearing protective gloves is recommended.
Tip: To facilitate the easy fastening of roof panels (Part W14, X26), please use double-sided
adhesive tape (Part H3) to affix Part S onto Panel (Part W14, X26) in advance. This will prevent Part S from sliding down during assembly.

X4

W14 , X26

Part S with adhesive tape
The back view of Panels

Alexander 12’x20′ assembly manual

page 21

Parts Required:

5#

6#

7#

10#

S x160

L 28mm x100

L 45mm

x8
L 50mm

x48

L 25mm x4

10#

Step 18: Affix roof panels

using screws and Spacers (Part S) as shown in the diagram.

6#

Align all roof panels and screws

LOOSELY (DO NOT TIGHTEN

ANY SCREWS) until all the roof

panels are aligned accordingly.

THEN, TIGHTEN all screws to

secure the roof panels in place.

S

X4

6#
X8

X100

5#

X48
7#

S 5#

Tip:

At least two people

2+

for this step.

Alexander 12’x20′ assembly manual

S 7#
page 22

Parts Required:

1#

11#

P12 x2

x6

x16

Q19 x2 Q20 x2

Step 19: Assemble Net Frames
Attach net frame (Part P12, Q19, Q20) to finishing barcPart P2, Q9, Q10) using screws (1#, 11#) as shown in the diagram.

N3 Q19

N2

Q20

N3

Upward View

N1

P12 N3 Q20
N1 P12

N2

Q19

P12 N3

11#

1# 11#

N3

Q20

N2

Q19

N3

1#

11#

Perspective Q19
Q20

1# 11#
P12

11#

1# 11#

P12 Q19

Q20
Tip: The perspective drawing is for demonstrating how to assemble the final step that sets up the Net Frame (Parts P12, Q19, Q20) more effectively.

Alexander 12’x20′ assembly manual

page 23

Parts Required:

S7 x2

S9 x2

Step 20: Assemble Net and Sidewall

Hang the Mosquito Net on the inner rails and the Solid Sidewalls on the outer rails as shown in the diagram.

Y7 x2

Y9 x2

4#
S7,S9 Y7,Y9

S7

12 ft
1

2

34

5

6

7

Y7

Y9

S9

8 910111213141 2 3 4 5

20 ft
543

21

Y7 S7

Sidewall Net

20 ft

S7

S9

S7

Y7

Y9

Y7

7th

1

S7

Y9
5th 5th
S9

Y7

1

7th

S7

Alexander 12’x20′ assembly manual

page 24

Parts Required:
SY X4
Step 21: When closing the Mosquito Net, refer to the steps below to align it with the poles, as
shown in the diagram.
æ

ê

é

S7,S9

Y7,Y9

è

ç

S7,S9

SY Y7,Y9

S7,S9

Y7,Y9

S7,S9

Y7,Y9

Care and Warranty
· Cleanse the frame components and fabric using a mild soap solution, then rinse thoroughly. Refrain from using bleach, acid, or any other solvents on the fabric or frame components.
· The roof, frame, bolts, and nuts are guaranteed to be free from defects in material and workmanship for a duration of one year from the date of purchase. The privacy curtain and mosquito netting are warranted for only 90 days. For a detailed warranty policy, kindly refer to www.kozyard.com. Please note that warranty terms are subject to change without prior notice.
· Regularly inspect and tighten all bolts and fasteners to ensure the optimal performance and safety of your gazebo.

Alexander 12’x20′ assembly manual

page 25

Thank you for your purchase of KOZYARD’s gazebo.
As expert manufacturer of hardtop gazebos, Kozyard remains committed to supporting you with parts and replacements, even beyond your warranty period.
Don’t hesitate to contact us directly if you are missing parts or need a replacement.
66
Kozyard LLC
© Copyright 2016 – 2023 Kozyard LLC. | All Rights Reserved.