KOZYARD KZAHG1212 12 Foot x12 Foot Alexander Hardtop Gazebo with Double Roof Instructions
- June 16, 2024
- KOZYARD
Table of Contents
12’x12’ Alexander Hardtop Gazebo
With Double Roof
Assembly Manual
KZAHG1212 12 Foot x12 Foot Alexander Hardtop Gazebo with Double Roof
Kozyard LLC Products
www.kozyard.com
© Copyright 2016 – 2023 Kozyard LLC. | All Rights Reserved.
Version:20231006
Warnings and Cautions
- Please read and follow this assembly and operation guide to reduce the risk of personal injury and damage to your gazebo.
- Do not discard any of the packaging until you have checked that you have all the parts in place. The maximum weight capacity of this gazebo roof is 2500 pounds.
- Sidewalls and nettings should be off or in the opened position and tied to poles when winds are over 30 MPH to avoid damage.
- Some parts may have sharp edges or corners. To ensure your safety, follow basic safety precautions to reduce the risk of injury. Please note that this item contains small parts which could be swallowed by children. Keep it out of reach of children under 3 years old and pets during installation.
Two or more people are required for aseembly and disassembly.
Do not fully tighten screw prior to complete assembly.
Pre-assembly
Tools that may be required.(Not included in boxes)
Note: Tools are not shown to actual size and scale.
Anchoring poles into concrete is strongly recommended.
Ensure the gazebo is positioned on level ground
Attention: Prior to assembly, verify that all parts and pieces are
included to ensure an efficient installation process.
| ITEM | DESCRIPTION | QTY |
|---|---|---|
| A | Pole | 4 |
| B6 | Beam | 4 |
| B61 | Jointer Bar | 4 |
| B62 | Sidewall Track | 4 |
| C6 | Beam | 4 |
| C61 | Jointer Bar | 4 |
| C62 | Sidewall Track | 4 |
| F | Union Bar | 4 |
| G | Corner Cover | 4 |
| H | Joint Cover | 4 |
| H1 | Joint Cover | 4 |
| H2 | Silcone Rubber | 1 |
| H3 | Double-sided adhesive tape | 1 |
| L | Plate | 4 |
| J1 | Corner Solidifyng Bar | 4 |
| J2 | Corner Solidifyng Bar | 4 |
| K2 | Inside Roof Connector | 1 |
| K12 | Outside Roof Connector | 1 |
| M1 | Short Corner Roof Bar | 4 |
| M2 | Corner Roof Bar | 4 |
| N1 | Roof Bar | 4 |
| P2 | Finishing Bar | 4 |
| P12 | Net Frame | 2 |
| Q12 | Net Frame | 2 |
| R | Finishing End | 8 |
| S | Spacer | 116+2 |
| T2 | Finishing Bar | 4 |
| U1 | Solidifying Bar | 8 |
| U3 | Iron Angle | 4 |
| U4 | Iron Angle | 4 |
| ITEM | DESCRIPTION | QTY |
|---|---|---|
| Z | Plastic Bracket | 72+2 |
| Z1 | Plastic Bracket | 8 |
| Z2 | Plastic Bracket | 8 |
| S7 | Solid Sidewall | 4 |
| Y7 | Mosquito Net | 4 |
| SY | Strap | 4 |
| V11 | Roof Panel | 4 |
| V12 | Roof Panel | 4 |
| W11 | Roof Panel | 4 |
| W12 | Roof Panel | 4 |
| W13 | Roof Panel | 4 |
| W14 | Roof Panel | 4 |
| W15 | Roof Panel | 4 |
| W16 | Roof Panel | 4 |
| W17 | Roof Panel | 4 |
| W18 | Roof Panel | 4 |
| 1# | Screws | 237+4 |
| 2# | Screws | 16+2 |
| 3# | Screws | 16+2 |
| 4# | Hook | 112+2 |
| 5# | Screws | 72+3 |
| 6# | Screws | 8+1 |
| 7# | Screws | 32+2 |
| 9# | Screws | 24+2 |
| 10# | Screws | 4+1 |
| 11# | Screws | 8+1 |
| 12# | Washer | 12+1 |
Parts Required:
Step 1: Set up Poles
- Set up Poles (Part A) with Stand Plates (Part L) using screws 1# as shown in the diagram.
Reference for anchoring gazebo:
- If the ground is concrete and its depth is over 3 inches, you can purchase 3/8″ diameter x 3″ length sleeve anchors.
- Only anchor after finishing all the assembly.
 Attention: After assembly, we strongly recommend anchoring the gazebo to your deck or con-crete as shown above. Damage resulting from wind or improper anchoring is not covered under warranty.”
Parts Required：
Step 2: Connect the Beams
Connected Beam Overall:- Connect Beams (Part C6 and B6) into one beam using Union Bar (Part F) with screws 1# as shown in the diagram.
 Parts Required:
Step 3: Connect Joint Bars and Tracks with Beams-
Connect Joint Bars (Part C61) and Tracks (Part C62) to Beam (Part C6) using screws 1#, as shown in the diagram.
Tip: Do not tighten all screws on the Jointer bars (Part C61 and B61) until the screws of the roof panels are aligned in place.
-
Replicate the same steps for Joint Bars (Parts B61), Tracks (Part B62) attaching them to Beams (Part B6) using screws 1# as shown in diagram.
-
 Step 4: Set up Poles and Beams
Use screws 3# first, then use screw 2# to connect Poles and Beams together as shown in diagram.
Step 5: Connect Solidifying Bars with Beams and Poles
Affix the frame with Corner Solidifying Bars (Parts J1, J2) using screws 1# as shown in diagram.
 Tip: Measure (DIAGONALLY) from posts to posts to assure alignment so all materials fit as planned.
Step 6: Cover the connections- Finish connecting the beams using Corner Covers (Part G) and screws 9# as shown in the diagram.
- Finish connecting the beams using Corner Covers (Part G) and screws 9# as shown in the diagram.
Step 7: Seal the seams
- After finishing Step 6, apply silicone rubber to the seams to ensure they’re watertight.
- If the screws are correctly attached through Spacer part S on the roof panels, sealing the cap screws with silicone rubber isn’t necessary.
 Step 8: Install Hooks
After finishing Hooks (Part 4#) into the tracks, then put Joint Cover (Part H1) to lock them.
Step 9: Connect Corner Roof Bar “M3”
Connect the Short Corner Roof Bar (Part M1) with Long Corner Roof Bar (Part
M2) using screws 1# and washer 12#.
Tip: The combination will be called “Part M3” in following
steps.
Step 10: Set up Roof Frame
- Connect the Inner Roof Connector (Part K2) with the Corner Roof Bar (Part M3) using screws 1#.
- Attach Corner Roof Bar(Part M3) to main frame using screw 1# as shown in diagram.
- Attach Finishing Bar (Part P2) with Finish End (Part R) using screws 1# to Corner Roof Bar (Part M3) as shown in diagram.
Step 11: Set up Roof Bar
Attach Roof Bar (Part N1) to main frame using screw 1# as shown in diagram.
 Step 12: Connect Outside Roof Connctor
Connect Outside Roof Connctor (Part K12) to Inner Roof (Part K2 ) using screw 1# as shown in diagram.
 Step 13: Snap Bracket
Snap Bracket (Part Z, Z1, Z2) to the roof panel edges as shown in the diagram.
Tip:- Wearing protective gloves is recommended.
- To prevent Z-Clips (plastic brackets) from sliding off prior to assembly, apply double-sided adhesive tape (Part H3) to the underside (bottom) edge of the roof panels where the brackets (Part Z, Z1, Z2) are supposed to attach.
- You can use super glue (not included) to attach the brackets to the roof panel if the double-sided tape doesn’t work for you.
Step 14: Assemble Roof Panel
- Push the Roof Panels (Part V11, V12) up to the upper roof as shown in the diagram.
- Attach Finishing Bars (Part T2) to the upper roof with Finish End (Part R) using screws #1, as shown in the diagram.
 Step 15: Connect Solidifying Bars
Attach Solidifying Bars ( Part U1) to roof bar or corner roof bar using Iron Angle (Part U3, U4) and screws 1# as shown in diagram.
Attention: If the holes on the Solidifying Bar (Part U1)
and the hole of the roof panel cannot be aligned, please adjust or loosen
screw 1# until the screws of the roof panel are in place.
Overall roof assembly:
Please place the panels on the frame and assemble them from the centerline
(Part N1) to the left and right.
Tip:
To facilitate the easy fastening of roof panels (Part W13), please use double-
sided adhesive tape (Part H3) to affix Part S onto Panel (Part W13) in
advance. This will prevent Part S from sliding down during assembly.
Step 16: Affix roof panels using screws and Spacers (Part S) as shown in the
diagram.
Align all roof panels and screws LOOSELY (DO NOT TIGHTEN ANY SCREWS) until all
the roof panels are aligned accordingly. THEN, TIGHTEN all screws to secure
the roof panels in place.
Step 17: Assemble Net Frame
Attach Net Frames (Part P12, Q12) to Finishing Bars (Part P2) using screws
(1#, 11#) as shown in diagram.
Tip: The perspective drawing is
for demonstrating how to assemble the final step that sets up the Net Frame
(Parts P12, Q12) more effectively.
Step 18: Assemble Net and Sidewall
Hang the Mosquito Net on the inner rails and the Solid Sidewalls on the outer
rails as shown in the diagram.
Step 19: When closing the Mosquito Net,
refer to the steps below to align it with the poles, as shown in the diagram.
Care and Warranty
- Clean the frame components and fabric with a mild soap solution, then rinse thoroughly. Avoid using bleach, acid, or any other solvents on either the fabric or frame components.
- The roof, frame, bolts, and nuts come with a guarantee against defects in material and workmanship for one year from the date of purchase. However, the privacy curtain and mosquito netting are warranted for just 90 days. For a comprehensive warranty policy, please visit www.kozyard.com. Be aware that warranty terms can change without prior notification.
- For the best performance and safety of your gazebo, inspect and tighten all bolts and fasteners regularly
As expert manufacturer of hardtop gazebos, Kozyard remains committed to
supporting you with parts and replacements, even beyond your warranty period.
Don’t hesitate to contact us directly if you are missing parts or need a
replacement.
SUPPORT:
Toll free: 1-866-355-0018
www.kozyard.com
email: support@kozyard.com
SOCIAL MEDIA: Follow us on Instagram
www.instagram.com/kozyard
Kozyard LLC
© Copyright 2016 – 2023 Kozyard LLC. | All Rights Reserved.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>