KZAHG1214BRW Alexander 12 ft. x 14 ft. Dark Brown Hardtop Gazebo

Product Information

Specifications:

• Product Name: 12’x14′ Alexander Hardtop Gazebo With Double
  Roof

• Manufacturer: Kozyard LLC Products

• Website: www.kozyard.com

• Version: 20231006

Warnings and Cautions:

• Two or more people are required for assembly and
  disassembly.

• Do not fully tighten screws prior to complete assembly.

Pre-assembly:

Tools that may be required (not included in boxes):

Note: Tools are not shown to actual size and scale.

Parts List:

Assembly Instructions:

Step 1: Set up Poles

1. 1. Attach Stand Plates (Part L) to Poles (Part A) using screws  

   1#.

Step 2: Anchoring the Gazebo

It is strongly recommended to anchor the gazebo into concrete
for stability. Ensure the gazebo is positioned on level ground.

Reference for anchoring gazebo:

• Anchor Block Size: Recommended minimum size is 12″x14″.
• Anchor Depth: 3 inches
• Anchor Diameter: 3/8 inches
• Anchor Type: M6 (Not included)

Step 3: Roof Assembly

1. 1. Attach Inside Roof Connectors (Part K4) to the inside of the  

   roof using screws 2#.

2. Attach Outside Roof Connectors (Part K14) to the outside of the
   roof using screws 2#.

3. Attach Short Corner Roof Bars (Part M1) and Corner Roof Bars
   (Part M2) to the Inside and Outside Roof Connectors using screws
   3#.

FAQ:

Q: How many people are required for assembly and

disassembly?

A: Two or more people are required for assembly and
disassembly.

Q: What should I do if some parts are missing?

A: Prior to assembly, verify that all parts and pieces are
included to ensure an efficient installation process. If any parts
are missing, please contact the manufacturer at support@kozyard.com for
assistance.

12’x14′ Alexander Hardtop Gazebo With Double Roof
Assembly Manual
Kozyard LLC Products
www.kozyard.com
© Copyright 2016 – 2023 Kozyard LLC. | All Rights Reserved.
Version:20231006

Warnings and Cautions
· Please read and follow this assembly and operation guide to reduce the risk of personal injury and damage to your gazebo.
· Do not discard any of the packaging until you have checked that you have all the parts in place. The maximum weight capacity of this gazebo roof is 2500 pounds.
· Sidewalls and nettings should be off or in the opened position and tied to poles when winds are over 30 MPH to avoid damage.
· Some parts may have sharp edges or corners. To ensure your safety, follow basic safety precautions to reduce the risk of injury. Please note that this item contains small parts which could be swallowed by children. Keep it out of reach of children under 3 years old and pets during installation.

Two or more people are required

2+

for aseembly and disassembly.

Do not fully tighten screw prior to complete assembly.

Pre-assembly
Tools that may be required.(Not included in boxes) Note: Tools are not shown to actual size and scale.

12’x14′ ANCHOR BLUEPRINT

6.77 in

12 in.

Safetyglasses

12 in.

136.88 in. ø0 .31 in.

Recommended Min. Anchor Block Size

160.7 in.
Anchoring poles into concrete is strongly recommended. Ensure the gazebo is positioned on level ground

Attention: Prior to assembly, verify that all parts and pieces are included to ensure an efficient installation process.

A x4

K4 x1

B6 x2 B61 x2 B62 x2 C6 x2

M3=M1+M2

M1 x4

K14 x1 L x4
M2 x4

F x4 H1 x4
J1 x4

C61 x2

N1 x2

C62 x2

N4 x2

G x4 H2 x1

D7 x2 D71 x2 D72 x2 E7 x2 E71 x2 E72 x2
H x4 H3 x1 J2 x4

ITEM DESCRIPTION

QTY

A Pole

4

B6 Beam

2

B61 Jointer Bar

2

B62 Sidewall Track

2

C6 Beam

2

C61 Jointer Bar

2

C62 Sidewall Track

2

D7 Beam

2

D71 Jointer Bar

2

D72 Sidewall Track

2

E7 Beam

2

E71 Jointer Bar

2

E72 Sidewall Track

2

F Union Bar

4

G Corner Cover

4

H Joint Cover

4

H1 Joint Cover

4

H2 Silcone Rubber

1

H3 Double-sided adhesive tape

1

J1 Corner Solidifyng Bar

4

J2 Corner Solidifyng Bar

4

K4 Inside Roof Connector

1

K14 Outside Roof Connector 1

L

Plate

4

M1 Short Corner Roof Bar

4

M2 Corner Roof Bar

4

N1 Roof Bar

2

N4 Roof Bar

2

Alexander 12’X14′ assembly manual

page 1

Q13 x2 R x8
U3 x4

P2 x2 P12 x2 Q4 x2 Q14 x2 S x128 T2 x2 T4 x2 U1 x4 U6 x4 U4 x4

V11 x2

V12 x2

V43 x2 V44 x2

V45 x2

V46 x2

W11 x2 W12 x2 W13 x2 W14 x2

W15 x2 W16 x2 W17 x2 W18 x2

ITEM DESCRIPTION
P2 Finishing Bar P12 Net Frame
Q4 Finishing Bar
Q13 Net Frame
Q14 Net Frame R Finishing End
S Spacer T2 Finishing Bar T4 Finishing Bar U1 Solidifying Bar U3 Iron Angle U4 Iron Angle U6 Solidifying Bar V11 Roof Panel
V12 Roof Panel
V43 Roof Panel V44 Roof Panel V45 Roof Panel V46 Roof Panel W11 Roof Panel W12 Roof Panel W13 Roof Panel W14 Roof Panel W15 Roof Panel W16 Roof Panel W17 Roof Panel W18 Roof Panel

QTY 2
2 2 2 2 8 128+2 2 2
4 4 4 4 2 2 2 2 2 2 2 2 2 2 2 2 2 2

Alexander 12’X14′ assembly manual

page 2

X41 x2 X42 x2 X43 x2 X44 x2

X45 x2 X46 x2 X47 x2 X48 x2

SY x4 Z1 x4 Z3 x2

S3 x2
Y3 x2
Z x76 Z2 x4 Z4 x2 4# x120+2 1# x246+4 2# x16+2 3# x16+2

S4 x2 Y4 x2

ITEM DESCRIPTION
X41 Roof Panel X42 Roof Panel X43 Roof Panel X44 Roof Panel X45 Roof Panel X46 Roof Panel
X47 Roof Panel X48 Roof Panel S3/S4 Solid Sidewall
Y3/Y4 Mosquito Net
SY Strap Z Bracket Z1 Bracket Z2 Bracket Z3 Bracket Z4 Bracket 1# Screws
2# Screws 3# Screws 4# Hook 5# Screws
6# Screws
7# Screws 9# Screws 10# Screws
11# Screws 12# Washer

5# x80+2
6# x8+1
7# x36+2
9# x24+2
10# x4+1
11# x12+1
12# x12+2
Allen key
Wrench
QTY 2 2 2 2 2 2 2 2 4 4 4
76+2 4 4 2 2
246+4 16+2 16+2 120+2 80+2 8+1 36+2 24+2 4+1 12+1 12+2

Alexander 12’X14′ assembly manual

page 3

Parts Required:

Step 1: Set up Poles
1. Set up Poles (Part A) with Stand Plates (Part L) using screws 1# as shown in the diagram.

A

A
X4
A x4

1#

1#

x12

1#

1#
L x4
L L

Reference for anchoring gazebo:
· If the ground is concrete and its depth is over 3 inches, you can purchase 3/8″ diameter x 3″ length sleeve anchors.
· Only anchor after finishing all the assembly.

3 inches
3/8 inches

M6

X12

(Not included)

Attention: After assembly, we strongly recommend anchoring the gazebo to your deck or concrete as shown above. Damage resulting from wind or improper anchoring is not covered under warranty.

Alexander 12’x14′ assembly manual

page 4

Parts Required

C6 x2

F x4

B6 x2

E7 x2
1#
X24

D7 x2

Step 2: Connect the Beams
1. Connect (Part C6,B6) into one beam using Union bar (Part F) with screws 1#
as shown in the diagram.

Short Beam Overall:
C6

B6

X2

F

B6
X2

B6 C6

C6

F 1#

1# 1#
1#

2. Connect (Part E7,D7) into one beam using Union Bar (Part F) with screws 1# as shown in the diagram.

Long Beam Overall:

X2

E7

D7

F

D7

D7

X2

E7

E7

F

1#

1#

1#

1#

Alexander 12’X14′ assembly manual

page 5

Parts Required:
C61 x2 C62 x2
E71 x2 E72 x2

1# x96

Step 3Connect Joint Bars and Tracks with Beams

C61

B61

B61 x2 B62 x2
D71 x2 D72 x2

C6 C62 E71

B6

B62

D71

E7

E72

D7

D72

1. Connect Joint Bars (Part C61,C62), Tracks (PartE71,E72) to Beams (Part C6 and E7) using screws 1# as shown in the diagram.
C6,E7
X2

Tip: Do not tighten all screws on the Jointer bars (Part B61, C61, E71, D71) until the screws of the roof panels are aligned in place.
B6,D7

C61,E71

1#
1# C62,E72

1# 1#
B62,D72

B61,D71

2. Replicate the same steps for Joint Bars (Part B61 and D71), Tracks (Part B62 and D72), attaching them to Beams (Part B6 and D7) using screws 1# as shown in the diagram.
X2

Alexander 12’X14′ assembly manual

page 6

Parts Required

2#

3#

x16

x16

Step 4: Set up Poles and Beams
Use screws 3# first, then use screw 2# to connect Poles and Beams together as shown in the diagram.

A
Tip: Place parts on carpet or rug to avoid scratches during assembly.

B6
X2
C6
A
C6

B6

3# 3#
2# 2#

X8

X8

B6

E7

C6

D7

X2

D7

C6

B6

E7

A

Tip:

At least three people

3+

for this step.

B6

A

C6

D7

A

Alexander 12’X14′ assembly manual

E7
A
page 7

Parts Required: J1 x4

1#

J2 x4

x32

J1

J2

1#

1#

1#

Step

5:

Connect

Solidifying

Bars

with

Beams

and

X4
Poles

Affix the frame with Corner Solidifying Bars (Parts J1, J2) using screws 1# as shown in the diagram.

J1 J2

Diagonal 1

J1

J2

J2

J1

Diagonal 2

J2 J1

Diagonal 1 = Diagonal 2

Tip: Measure (DIAGONALLY) from posts to posts to assure alignment so all materials fit as planned.

Alexander 12’X14′ assembly manual

page 8

Parts Required:

G x4

H x4

9# x24

9#

9#

G
9#
X4
Step 6: Cover the connections
1. Finish connecting the beams using Corner Covers (Part G) and screws 9# as shown in the diagram.

H

X4

2. Affix the middle beams using Joint
Cover (Part H) and screws 9# and 1#
as shown in the diagram.

Alexander 12’X14′ assembly manual

page 9

Parts Required:

H2 x1

Step 7: Seal the seams
1. After finishing Step 6, apply silicone rubber to the seams to ensure they’re watertight. 2. If the screws are correctly attached through Spacer part S on the roof panels, sealing the cap
screws with silicone rubber isn’t necessary.

X4

Alexander 12’X14′ assembly manual

page 10

Parts Required:

4# x120

H1 x4

Step 8: Install Hooks

After inserting Hooks (Part 4#) into the tracks, secure them by placing the Joint Cover (Part H1) to lock them in place.

1# x4

4#
4#

X4
4#

Note the

amount of

hooks for

4#

each slot

H1

as noted

1# H

below:

X2
Put 7 hooks in each slot of sidewall track (part C62
Part B62).

4#

C62

C6

B6

x7

x7

H1

x7

Put 8 hooks in each slot of sidewall track (part E72, Part D72).

B62
x7
X2

4#

E7

D7

E72

H1

D72

x8

x8

x8

x8

Alexander 12’X14′ assembly manual

page 11

Parts Required:
K4 x1

M2 x4

Step 9: Connect Corner Roof Bar “M3”

Connect the Short Corner Roof Bar (Part M1) with Long Corner Roof Bar (Part M2) using screws 1# and washer 12#..

M2

Tip: The combination will be called “Part M3” in following steps.
M3=M1+M2

Tip:
M2

12#

M1 x4

x12

1# x12

M1

1# 12#
X4

M1

1# 12#

Step 10: Set up Roof Frame

M3

Upward View

M3

Q4

P2 M3

K4 Q4
Alexander 12’X14′ assembly manual

P2
M3
page 12

Parts Required:

1#

P2 x2

R x4

x16

Q4 x2

1. Connect the Inner Roof Connector(Part K4) with the Corner Roof Bar (Part M3) using screws 1#.

M3 M3

1#

X4

K

M3

M3

M3 2. Attach Corner Roof Bar(Part M3)

to main frame using screw 1#

as shown in the diagram.

1#

P2

3. Attach Finishing Bar (Part P2, Q4) with Finish End (Part R) using screws 1# to

X4

Corner Roof Bar (Part M3) as shown in

the diagram.

K4

M3

P2

M3

M3 Q4

M3 R 1#
Q6
X4

Tip:

At least two people

2+

for this step.

Alexander 12’X14′ assembly manual

page 13

Parts Required:

N1 x2

N4 x2

1#

x12

Upward View
N4

N1 1#

1#

N1

1#

1#

K4

N4

N1 or N4
1#

X4 Step 11Set up Roof Bar
Attach Roof Bar (Part N1,N4) to main frame using screw 1#.
Attention: The part N4 must be placed on the 14′ side

N4

N1

N4 N1

Alexander 12’X14′ assembly manual

page 14

Parts Required:
Upward View

K14 x1

1# x2

1#

1#

K14

K4

Step 12Connect Outside Roof Connctor
Connect Outside Roof Connctor (Part K14) to inside roof (Part K4) using screw 1# as shown in the diagram
K14

Alexander 12’X14′ assembly manual

page 15

Parts Required:
Z3

V11 V12

V43

V44

V45

V46

Z4

Step 13: Snap Bracket
Snap Bracket (Part Z, Z1, Z2, Z3, Z4) to the roof panel edges as shown in the diagram.
(with snaps facing upwards)

X2

Z1

Z2

H3 x1

Z Z2

Z Z1

V11

Z

Z Z4

V43

V44

V12

Z
V45

Z Z3
V46

Tip: 1. Wearing protective gloves is recommended. 2. To prevent Z-Clips (plastic brackets) from sliding off prior to assembly, apply
double-sided adhesive tape (Part H3) to the underside (bottom) edge of the roof panels where the brackets (Part Z, Z1, Z2, Z3, Z4) are supposed to attach. 3. You can use super glue (not included) to attach the brackets to the roof panel if the double-sided tape doesn’t work for you.

Alexander 12’X14′ assembly manual

page 16

Parts Required:
T2 x2
V46
R

T4 x2
V45

T2

V 11

R x4
T4 V44

1# x8
V43
R
V12
T2

1#
V12

V 11

R

V43

V44

1#

R

V45

V46

1#

T4

Step 14Assemble Roof Panel
1. Push the Roof Panels (Part V11, V12, V43, V44, V45,V46) up to the upper roof as shown in the diagram.
2. Attach Finishing Bars (Part T2, T4) to the upper roof with Finish End (Part R) using screws #1, as shown in the diagram.

V11 V12

V43 V44 V45 V46

T2 1#

R 1#

T4

1#

Alexander 12’X14′ assembly manual

page 17

Parts Required:
U6 U6

U1 x4

1#

U6 x4

U3 x4

U4 x4

x24

U1 U1

U1

U6

U6

U1

Attention: If the holes on the Solidifying Bar (Part U1, U6) and the hole of the roof panel cannot be aligned, please adjust or loosen screw 1# until the screws of the roof panel are in place.
Step 15: Connect Solidifying Bars
Attach Solidifying Bars ( Part U1, U6) to Roof Bar or Corner Roof Bar using Iron Angle (Part U3, U4) and screws 1# as shown in diagram.

X4
1#

X4
U4

U3

Alexander 12’X14′ assembly manual

1#

page 18

Parts Required:

x32

W11 x2 W12 x2 W13 x2 W14 x2 W15 x2 W16 x2 W17 x2 W18 x2

Step 16: Snap Bracket

Snap Brackets (Part Z) to roof panel edges as shown in the diagram.

(with snaps facing upwards)

X2

Z

Z

Z

Z

Z

Z Z

Z

Z

H3 x1

W11

W12

W13

W14

Tip:
1. Wearing protective gloves is recommended. 2. To prevent Z-Clips (plastic brackets) from sliding off prior to assembly,
apply double-sided adhesive tape (Part H3) to the underside (bottom) edge of the roof panels where the brackets (Part Z) are supposed to attach. 3. You can use super glue (not included) to attach the brackets to the roof panel if the dZouble-sided tape doesn’t work for you

Z Z Z

Z Z Z Z

W15

W16

W17

Alexander 12’X14′ assembly manual

W18
page 19

Parts Required:

x32

H3 x1

X41 x2 X42 x2 X43 x2 X44 x2 X45 x2 X46 x2 X47 x2 X48 x2
Step 17Snap Bracket
Snap Brackets (Part Z) to roof panel edges as shown in the diagram. (with snaps facing upwards)
X2
Z
Z
Z
Z
Z
Z
Z Z
Z

X41

X42

X43

X44

Tip: 1. Wearing protective gloves is recommended. 2. To prevent Z-Clips (plastic brackets) from sliding off prior to assembly,
apply double-sided adhesive tape (Part H3) to the underside (bottom) edge of the roof panels where the brackets (Part Z) are supposed to attach. 3. You can use super glue (not included) to attach the brackets to the roof panel if the double-sided tape doesn’t work for you
Z

Z Z

X45

Z Z

X46

X47

Alexander 12’X14′ assembly manual

Z Z Z
X48
page 20

Overall roof assembly:
Please place the panels on the frame and assemble them from the centerline (Part N1,N4) to the left and right.

X7 X8

N4 N1

X1 W18

X2

W17

X3

W16

X4

W15

X5

W14

X6

W13

W12

W11

W11 W12

W13 W14

W15

W16

N1

W17 W18

X42 X43

X45 X46 X44

X47 X48

X41

N4

Connect roof as below:

Tip:
Wearing protective gloves is recommended.

Tip: To facilitate the easy fastening of roof panels (Part W14, X44), please use double-sided
adhesive tape (Part H3) to affix Part S onto Panel (Part W14, X44) in advance. This will prevent Part S from sliding down during assembly.
X4

W14 or X44
Alexander 12’X14′ assembly manual

Part S with adhesive tape
page 21

Parts Required: 10#

5#

6#

S x128

x80

x8

Step 18: Affix roof panels using
screws and Spacers (Part S) as shown
in the diagram.

7# x36
6#

S
X4

Align all roof panels and screws

LOOSELY (DO NOT TIGHTEN ANY

SCREWS) until all the roof panels are

aligned accordingly. THEN, TIGHTEN all

screws to secure the roof panels in

place.

S
6#

10# x4
X8

X36
7#

X80
5#

2+
Tip: At least two people for this step.
Alexander 12’X14′ assembly manual

page 22

Parts Required:

P12

Q13 x2

Q13

Upward View

Q14 x2
Q14

1#

11#

x4

x12

P12

P12

Q14

Q13

Step 19: Assemble Net Frame
Attach Net Frames (Part P12, Q13, Q14) to Finishing Bars Part P2, Q4
using screws (1#
11#) as shown in the diagram.

Q14

Q13

11# 11#
Perspective:

1# 11#
X2
Q13 Q14

11#

P12 11#

P12 N1

Q14 Q13
N4

1#
X2

11#

Tip: The perspective drawing is for demonstrating how to assemble the final step that sets up the Net Frame (Parts P12, Q13, Q14) more effectively.

Alexander 12’X14′ assembly manual

page 23

Parts Required:

S3 x2

S4 x2

Y3 x2

Y4 x2

Step 20Assemble Net and Sidewall
Install the Mosquito Net on the inner rails and the Solid Sidewalls on the outer rails as shown in the diagram.
4#

S3 or S4

Y3 or Y4

S3

S4

Y3

Y4

14

ft
1

2

34

5

6

7

8

9 10111213141512 ft

7th 1 15th
9th

12 ft

14 ft S4
Y4

S3 Y3

Y3

8th

15th

S3

Y4

1

8th

S4

Alexander 12’X14′ assembly manual

page 24

Parts Required:
SY X4
Step 21: When closing the Mosquito Net, refer to the steps below to align it with the poles, as
shown in the diagram. æ

ê

é

S3,S4

Y3,Y4

è

ç

S3,S4

SY Y3,Y4

S3,S4

Y3,Y4

S3,S4

S3,S4

Y3,Y4

Care and Warranty
· Clean the frame components and fabric with a mild soap solution, then rinse thoroughly. Avoid using bleach, acid, or any other solvents on either the fabric or frame components.
· The roof, frame, bolts, and nuts come with a guarantee against defects in material and workmanship for one year from the date of purchase. However, the privacy curtain and mosquito netting are warranted for just 90 days. For a comprehensive warranty policy, please visit www.kozyard.com. Be aware that warranty terms can change without prior notification.
· For the best performance and safety of your gazebo, inspect and tighten all bolts and fasteners regularly

Alexander 12’X14′ assembly manual

page 25

As expert manufacturer of hardtop gazebos, Kozyard remains committed to supporting you with parts and replacements, even beyond your warranty period.
Don’t hesitate to contact us directly if you are missing parts or need a replacement.
66
Kozyard LLC
© Copyright 2016 – 2023 Kozyard LLC. | All Rights Reserved.

References

• Kozyard LLC Official Web Site
• Yard.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>