RYNOSKIN RS-FFF-001 Front Fender Flares Instruction Manual
- June 16, 2024
- RYNOSKIN
Table of Contents
FB1 FLAT FRONT FENDER FLARES
INSTALLATION INSTRUCTIONS
PART NO. RS-FFF-001
Fits:
2021-2024 FORD BRONCO 2 DOOR & 4 DOOR
RS-FFF-001 Front Fender Flares
90-180min
Installation time is different according to individual person.
Cutting Not Required
Drilling Not Required
TOOLS REQUIRED
WRENCH/SOCKET SET DO NOT OVER TORQUE. PLEASE FOLLOW THE TIGHTEN OPERATING LOAD
STANDARD BELOW:
6mm BOLTS & NUTS: FROM 7 TO 8.5 FOOT POUND.
8mm BOLTS & NUTS: FROM 18 TO 20 FOOT POUND.
10mm BOLTS & NUTS: FROM 35 TO 40 FOOT POUND.
12mm BOLTS & NUTS: FROM 60 TO 70 FOOT POUND.
TO PROTECT YOUR INVESTMENT, DO NOT USE ANY TYPE OF POLISH OR WAX THAT MAY
CONTAIN ABRASIVES THAT COULD DAMAGE THE FINISH. MILD SOAP MAY BE USED TO CLEAN
THE PRODUCTS.
PARTS LIST:
| Description | Qty | Image | Remark |
|---|---|---|---|
| Driver/Left Front Fender Flare | 1 | ||
| Passenger/Right Front Fender Flare | 16 | ||
| 6mm x 25mm Button Head Bolts | 16 | ||
| 6mm x 12mm OD x 1.6mm Flat Washers | 1 | ||
| 6mm Lock Washers | 1 | ||
| 6mm Nut Plates | 16 | ||
| 4mm Hex Wrench | 16 |
FB1 FLAT FRONT FENDER FLARES
2021-2024 FORD BRONCO 2 DOOR & 4 DOOR
PROCEDURE:
REMOVE CONTENTS FROM BOX. VERIFY ALL PARTS ARE PRESENT. READ INSTRUCTIONS CAREFULLY. ASSISTANCE IS RECOMMENDED.
- Start installation on the Driver/Left side of the vehicle. Locate the (5) plastic clips attaching the fender to the body of the vehicle, (Figure 1). Rotate counter clockwise to release the clips. Carefully pry the fender away from the vehicle and place in a safe location, (Figure 2).
- Locate the hardware attaching the fender liner to the outer edge of the wheel well. Temporarily remove the hardware to access the backside of the fender location.
- Select the Driver/Left Fender. With assistance, hold up the Fender to the mounting location. Determine the holes needed in the body. Attach the holes in the Fender to the body with (8) 6mm Button Head Bolts, (8) 6mm Lock Washers, (8) 6mm Flat Washers and (8) 6mm Nut Plates, (Figures 3 & 4). Do not tighten hardware.
- Adjust the position of the Fender and fully tighten all hardware.
- Repeat Steps 1—4 for Passenger/Right side Fender installation.
- Do periodic inspections to the installation to make sure that all hardware is secure and tight.
FB1 FLAT FRONT FENDER FLARES
2021-2024 FORD BRONCO 2 DOOR & 4 DOOR
Driver/Left Side Installation Pictured
Documents / Resources
|
RYNOSKIN RS-FFF-001 Front Fender
Flares
[pdf] Instruction Manual
RS-FFF-001 Front Fender Flares, RS-FFF-001, Front Fender Flares, Fender Flares
---|---
|
RYNOSKIN RS-FFF-001 Front Fender
Flares
[pdf] Instruction Manual
RS-FFF-001 Front Fender Flares, RS-FFF-001, Front Fender Flares, Fender
Flares, Flares
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>