MAIWO K2022R NVMe RAID Enclosure Dual Bay Instructions
- June 16, 2024
- MAIWO
Table of Contents
**MAIWO K2022R NVMe RAID Enclosure Dual Bay Instructions
**
Product Overview
Product Name
Product name: MAIWO Dual Bay M.2 NVMe SSD Enclosure
Product Model : K2022R
Support SSD: M.2 NVMe(M-KEY/B&M KEY)
Interface| Type-C Interface
Material| Aluminum Alloy+ABS Plastic
Main Function| Data Transmission,RAID Function: RAID 0, RAID 1, LARGE,
PM
Product Size| 120X68X16.7MM
System| Windows, Mac OS, Linux, etc
Indicator status| Power light: blue (steady on when reading/writing);SSD
light: white (flash when reading/writing, off when sleep, red when fault);RAID
mode light: blue.
Read&Write Function:
Insert the SSD on the corresponding interface of middle frame, secure them with the silicone plugs (note: the SSD should be NVMe M.2 SSD, not SATA M.2 SSD), put the middle frame in the aluminum shell.
Connect the enclosure to power (by DC port) and computer (by Type C port).
Press the power button, blue power light will be on, then the corresponding white light of SSD will be on.
Note: if it is a used SSD, you can find the new drive on “computer”, read &write normally. If it is a new SSD, need to initialize, partition, format firstly before use. 11
Raid Set Up
Attention: Back up HDD/SSD data before setting or switching RAID modes, otherwise the data will be lost! 2.1.
Default mode is PM mode:
Connect to power and PC, press the power button, then you can read / write 2 SSD. In PM mode, the 2 SSD are in a independent state without mutual influence.
RAID 0 Mode:
Set RAID 0 mode as the schematic diagram on the right. Connect to power and PC. Long press and hold the “Reset” button, short press the power button at the same time. (Keep pressing the “Reset” button for 3-5 seconds until RAIDO Indicator light is on)
RAID Set up: !
Attention: Back up HDD/SSD data before setting or switching RAID modes, otherwise the data will be lost!
RAID 1 Mode:
Set RAID1 mode as the schematic diagram on the right. Connect to power and PC. Long press and hold the “Reset” button, short press the power button at the same time. (Keep pressing the “Reset” button for 3-5 seconds until RAID1 indicator light is on)
LARGE Mode:
Set LARGE mode as the schematic diagram on the right. Connect to power and PC. Long press and hold the “Reset” button, short press the power button at the same time. (Keep pressing the “Reset” button for 3-5 seconds until LARGE Indicator light is on).
Attention: When one of the HDD/SSD is damaged and have to be replaced, make sure the HDD/SSD for replacement is new, or haven’t set RAID modes before.
New hard disk format:
View “computer- Manage – Disk Management” to find the new disk.
Note: There are two formats when initialization, please choose MBR if your drives are smaller than 2TB, choose GPT if your drives are larger than 2TB.
Hard disk partition:
Right click the “Disk 1”, then click “New Simple Volume”
According to the instruction, choose the size of partition, then click “Next” to finish. 3.4. Then you can find the new hard disk in the “Computer, it s readyto be use.
Documents / Resources
|
MAIWO K2022R NVMe RAID Enclosure Dual
Bay
[pdf] Instructions
K2022R NVMe RAID Enclosure Dual Bay, K2022R, NVMe RAID Enclosure Dual Bay,
RAID Enclosure Dual Bay, Enclosure Dual Bay, Dual Bay
---|---
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>