CPVAN CP-SN12 Wireless Outdoor Alarm Siren with Strobe Light User Guide

: June 6, 2024
: CPVan

Table of Contents

PCB Diagram
Siren alarm tone setting
Wired defense zone
Usage
Pairing with wireless accessories
Deleting all wireless accessories
Installation
Specifications
Read User Manual Online (PDF format)
Download This Manual (PDF format)

CPVAN CP-SN12 Wireless Outdoor Alarm Siren with Strobe Light User Guide

This siren is completely free of wires, with a rechargeable solar-powered battery, it can be used as a standalone siren, works with other wireless sirens or accessories on the same alarm system. It can also work as an on-site alarm system/panel when paired with other wireless accessories, such as door / window sensors, PIR sensors and remote control etc on the same wireless frequency.

When any detector to which the alarm belongs is triggered, the alarm panel will immediately sound in high decibel to deter illegal intruders with warning light flashes.

PCB Diagram

Siren alarm tone setting

Alarm sound frequency

600~1500Hz for 0.333~0.385s （Default)
800Hz & 1000Hz for 1.67~2.5s
600~1500Hz for 3~5s
Same as default

Alarm sound delay time setting

Delayed by 1 minute (factory default)
Delayed by 3 minute
Delayed by 5 minute

Wired defense zone

The siren has two wired defense zones Z0 and Z1, which can be connected to wired detectors through a wire. When the wired detector triggers an alarm, the siren will sound and flash.。

Note: The wired defense zone of this device only supports normally open wired detection, and it is effective in the armed status.

Usage

Work as a wireless siren

Please connect the siren to a wireless alarm panel first when it’s used as a wireless siren. And once the panel triggers an alarm, the siren will sound and flash.

Pairing with alarm panel

Pressing and hold the SET button for 2s until the siren beep for one time, and the warning light is always on indicating that the siren has been in sniffer mode. Then press SOS on the alarm panel, when the long beep is heard from the siren and the warning light quickly flashes once, indicating that the pairing with panel is successful. When the short three beeps is heard and the warning light quickly flashes for 3 times, means the siren has been paired. If there is no operation is made for more than 20s, the siren will automatically exit the sniffer mode.

Test

Pressing SOS key on the alarm panel, the siren sounds and flashes, indicating that the paring with alarm panel is successful.

Working as an on-site alarm panel

When the siren is connected with wireless detectors, it can works as an on- site alarm panel. When the siren is armed and an alarm is triggered, it will sound and flash.

Pairing with wireless accessories

Pressing and hold the SET button for 2s until the siren beep for one time, and the warning light is always on indicating that the siren has been in sniffer mode. Then press any key on the remote control or the detector to be learned, when the long beep is heard from the siren and the warning light quickly flashes once, indicating that the pairing with siren is successful. And it will automatically exit the learning state.
When the short three beeps is heard and the warning light quickly flashes for 3 times, means the siren has been paired (repeat code). If there is no operation for more than 20 seconds in the learning state, the siren will automatically exit the sniffer mode.

Test

Pressing the 【arm】 button on the remote control, a short beep is heard from the siren means that the pairing between the remote control and siren is successful. Or triggering the detector when the siren is armed, if the siren sounds, means the pairing is successful.

How to arm, home arm, disarm or make an alarm with remote control

You can use remote control to quickly away-arm, home-arm and disarm your home, and to trigger an emergency alarm.

Button	What you hear	What you see	What happens
Arm	Short beep once	Warning light quickly flashes once (and the siren
will flash once per 1min)	The alarm sounds when a door or window opens, or

Deleting all wireless accessories

Pressing and hold the SET button for 5s until three long beeps is heard，meanwhile the warning light flashes for 3 times and goes out , indicating that all wireless accessories are deleted from the siren, and the siren is also unbound with alarm panel.