ATTOP XT-10 Drone with Camera User Manual

14 + age
X-PACK 10 User Manual
(Suitable for wide indoor environments operation)
Suitable for 14 years old and above

XT-10 Drone with Camera

Get 24/7 assistance at

Use camera or QR scanner to scan
Visit: https://attop.afterservice.vip
Call: +1 (833) 307 2271 (Toll-free)
Email: attop@afterservice.vip
www.attoptoys.com
Customer Service Email : attop@afterservice.vip
Made in China

Aircraft Parameters

Length of main wing: 83mm
Aircraft: 98X120X33mm
Total weight: 54g±2g
Battery: 3.7V 380mAh
Charging time: About 50 mins
Flight time: 7-8 mins
Gyroscope: built-in
Working temperature: 14°F to 104°F
Remote controller: 2.4G
Motor: 7*16 4pcs

Remote Controller Parameters

Wifi Transmission Range: 30-40 meters
(in a wide open area with no electromagnetic interference)
Working frequency: 2.4G
Battery: 3xAAA

Package Contents

Charging

• When the drone’s battery is low, there are continuous beeps from the controller and the drone’s LEDs keep flashing.
• Please use the original battery and USB cable provided.
• Keep the battery away from any sharp objects that could puncture into the battery to avoid risks of explosion and fire.
• It’s not recommended to charge the battery from the USB port of PC.
• Flight time may be reduced when flying in low-temperature environments.

Note: Please fully charge the battery before flying.

Remote Controller

1. Photo
2. Speed Switch (short press)
Emergency Stop (long press)| 3. Video
4. 360° Flip4
---|---

1. Phone Clamp
2. Left Control Stick
3. ON/OFF
4. One Key Take-Off/Landing
5. Circle Fly
6. Headless Mode (short press)
One Key Return (long press)
7. High-Speed Rotation| 8. LED Indicator
9. Right Control Stick
10. Drone’s LED Indicators
11. Forward Trim
12. Rightward Trim
13. Backward Trim
14. Leftward Trim
---|---

Installing

1. Open up all 4 blades of the drone.This aircraft is a folding structure, please make sure to open all four blades before taking off.

2. Blades Protector Installing.Expand the buckle of the protector, and install it onto the drone wings.

3. Replace the propellers when it’s needed. (Optional).a. Loosen the screws, then remove the cap.
   b. Take out the propellers.
   c. Fit the spare propellers into the drone according to the mark (A/B) on them.
   d. Install the cap and tighten the screws.
   Note:
   Please do not overtighten the screws. Gently rotate the propellers by hand after installation to check whether they are rotatable, if not, please loosen the screw and check again.

4. Install the battery into the drone after it’s fully charged.

5. Install the controller batteries.When the controller’s battery is low, there are continuous beeps from the remote and its LED indicator keeps flashing.

6. Unfold the phone clamp to place your mobile device.

How to Fly

1. Switch on the power.
   1. First power on the drone. (Keep pressing for 2 seconds and place it on a flat ground or surface.)2. Press and hold the ON/OFF button to turn on the controller, you will hear a beep from the controller and its LED indicator starts flashing.

2. Frequency matching.After turning on the drone, both indicator lights on the drone and controller will flash, then push the left throttle to the top, then down to the lowest, after 2 seconds, the indicators will go steady, which means the frequency matched successfully.

3. Compasses calibration.Move both control sticks to lower left at 45°, you’ll hear a beep from the remote. Calibration completes when the LEDs of the drone turn to solid on from flashing.

4. Flight Instructions.
   Option 1:
   Press the button to take off. Option 2:
   Simultaneously push the Left Control Stick to lower left at 45° and the Right Control Stick to lower right at 45° (or push the Left Control Stick to lower right at 45° and the Right Control Stick to lower left at 45°) until the four propellers start rotating, then slowly push the Left Control Stick forward to take off. Option 3:
   Throw-to-fly function After frequency matching and calibration finished, you can hold the aircraft in your hand, and then horizontally throw it out. The aircraft will automatically unlock the blades and fly in the air.
   Note: It is better to operate the calibration step again after operating throw-to-fly for several times. The function will be more stable.

Using the Remote Controller

Left Control Stick

| | Push the Left Control Stick forward, the drone will ascend; pull it backward and the drone will descend.
---|---|---
| | Pull the Left Control Stick leftward, the drone will rotate to the left; pull it rightward ,the drone will
rotate to the right.

Right Control Stick

| | Push the Right Control Stick forward, the drone will fly forward; pull it backward, the drone will fly backward.
---|---|---
| | Pull the Right Control Stick leftward , the drone will fly leftward; pull it rightward , the drone will fly
rightward.

Flight Trimming

| | If the drone drifts forward or backward when hovering, press the Backward Trim button or the Forward Trim button to adjust.
---|---|---
| | If the drone drifts leftward or rightward when hovering, press the Rightward Trim button or the Leftward Trim button to adjust.

FLIGHT OPERATION GUIDE
IMPORTANT

• Make sure that you power on your drone first, and then turn on the controller before each flight.
• Please repeat the pairing and calibration procedure each time while the drone or controller is restarted.
• For all flight functions and modes, the operator and tail of the drone must be aligned.

Aircraft Functions

(1) Speed Switch.
The drone is set to low speed by default.
Press the button once for medium speed and there are two beeps from the controller. Press it again for high speed and there are three beeps from the controller. Press it the third time to get back to low speed and there is one beep from the controller.
(2) Headless Mode.
Short press the button to activate Headless Mode; LEDs on the drone start flashing.
In this mode, the drone will fly following the direction of the Right Control Stick regardless of the position of your drone’s head or tail. Press the same button to exit this mode; LEDs on the drone turn to solid on.
(3) 360° Flip.
Fly the drone to a height over 2m, then press the button to activate 360° Flip function. Next, move the Right Control Stick to flip the drone accordingly. Note:

• There are continuous beeps from the remote when you activate this function. If you do not move the Right Control Stick about 5s after you press the button, the function will be canceled and the remote will stop beeping.
• This function can’t be activated when the battery of the drone is low.
  (4) One Key Return.
  a. Press and hold the button, then the drone will fly toward its back following a path parallel to its original take-off path. The LEDs on the drone keep flashing when the drone is returning.
  b. Press and hold the button again or move the Right Control Stick forward to cancel this mode, or the drone will keep flying back. (5) High-Speed Rotation.
  Press the button to make the drone rotate at high speed.
  Press the button again or move the Right Control Stick to any direction to exit this mode. Note:
  This function can’t be activated when the battery of the drone is low.
  (6) Circle Fly.
  In the case of barrier-free within 5m radius around the drone, press the button to fly the drone in a circle.
  Press the button again or move the Right Control Stick to any direction to exit this mode. Note:
  This function can’t be activated when the battery of the drone is low.
  (7) Photo / Video.
  Please connect the drone to your mobile device first, then go to the ‘Media’ in app Home Page or your album file of the device to check your photos and videos.
  Press the button to take a photo. Press the button to start recording a video; press it again to stop recording and saving the video. Note:
  It’s NOT recommended to use this function during normal flight for landing, which may result in serious damage to your drone.
  (8) Altitude Hold/Hover.
  This is one of the default settings of the drone. When you release the Left Control Stick after an ascent/descent action, the drone will hover at the current flight height. For a stable flight, press the trim buttons to adjust accordingly.
  (9) Emergency Stop.
  Press and hold the button, then the drone will stop in the air and fall.

| ISSUES| CAUSE| SUGGESTIONS
---|---|---|---
1.| After the battery is inserted in the drone, indicator lights on drone keep flashing, and does not respond to operation.| Frequency matching between controller and receiver is not successful.| Reoperate the frequency matching for controller and drone. (please refer to P.6 for details).
2| No response after battery is inserted in the drone.| 1.Check whether the power for controller and drone is fully charged.
2.Connection of the poles is not good.| 1.0pen the remote battery case and make s. ure the battery is
inserted in right position.
2.Use a fully charged battery.
3.Reinstall the batter y and confirm whether it is of good connection with the poles.
3| Motor does not run when operating the throttle stick and the indicator lights on drone keeps flashing.| Power for the Li-Poly battery is not enough.| Charge the battery or replace it with a full charged battery.
4| Main motor blades spin but the drone won’t fly.| 1.Some of the blades have been deformed.
2.Battery power is not enough.| 1.Replace the main blade.
2.Charge the battery or replace it with a fully charged battery.

Battery Using Attention

Matters needing attention

1. Rechargeable batteries are to be removed from the toy before being charged.

2. Non-rechargeable batteries are not to be recharged.

3. Rechargeable batteries are only to be charged under adult supervision.

4. Only used to charge 2S Li-ion or Li-polymer battery pack. if not, the charger or battery may be damaged.

5. During charging, the charger should be put in the dry and ventilated place and far away from heat sources and inflammable and explosive substances.

6. Never immediately charge your battery pack as soon as the flight is finished, or when its temperature doesn’t cool down. Otherwise the battery will take a risk in swelling, even a fire.

7. Ensure the correctness of polarity before connecting the battery to charger.

8. Avoid drop and violence during the process of charging. Drop and violence will result in an internal short circuit of the battery.

9. For the sake of safety, please use original charging equipment and battery pack.
   Please change new one in time when the flying time is becoming shorter due to long time usage.

10. If it is retained in the charger for a long time after being saturated, the battery may automatically discharge. When the charger detects that the voltage of individual cells is lower than the rated voltage, it will recharge until saturated. Frequently charging and discharging will shorten the lifetime of your battery pack. It is advised that please cut off the power and take off the battery after the charging is saturated.

Maintenance of battery pack

1. The battery pack should be put in the dry and ventilated place. The storage temperature of environment is ranged from 64.4°F to 77°F.
2. Please avoid frequent charging and excessive discharging of the battery pack in order to prolong its life cycle.
3. It is a must to maintain the battery pack before long-term storage. That is to charge the battery to the level of 50-60% saturation.
4. If the storage term is over 1 month, it is advised to monthly check the voltage of every cell of the battery pack. The voltage of every cell should be not less than 3V. Otherwise, please refer to the above article （3）.
5. From the view point of protection, new battery pack should be motivated before usage. That is to charge and discharge 3-5 times, but discharge is not less than the level of 70% saturation. This process will make the battery life longer and voltage more stable.

SAFETY AND PRECAUTIONS

CAUTION
Remote-control models of quadcopter are dangerous merchandise. Their flight must be operated away from the crowd. Such factors as man-made improper assembly or mechanical damage, poor control of the electronic equipment, as well as the unfamiliar manipulation may lead to unexpected flight accidents, such as uncontrolled flight and aircraft damage. Users are advised to pay attention to the flight safety and understand that they are held responsible for any accident caused by negligence.

FORBIDDEN
Special drone for indoor and outdoor should stay away from barriers
This product is a remote-control drone, which is suitable for in indoor using and outdoor environments (the outdoor wind power less than Force 2). To fly this drone, please choose appropriate obstacle-free indoor and outdoor sites with proper distance kept from the crowd or pet animals. Please don’t operate the product in any unsafe environments, such as places of heat, wires, power supply, etc., so as to prevent the quadcopter from the risks of fire and electric shock resulting from collision, ditching, and entangling of the drone.|
FORBIDDEN
Safe usage of the lithium battery
Lithium batteries are more dangerous than others. Be sure to read carefully and follow the following precautions before using it. We will not be held responsible for any damages caused by any improper use of the battery. To avoid the danger of explosion or fires, it is forbidden to use other chargers than the one made by our factory. Such actions done to the battery as impact, dismantling, reverse connection of the positive and negative poles, and burning are forbidden. Avoid metal objects from
contacting the positive and negative poles of the battery, which may cause short circuit. Please prevent sharp items from piercing the battery, and avoid the risk of battery fire. Please be careful when charging the battery. Make sure that the battery is charging within your sight. Keep it out of the
reach of young children so as to avoid dangers. Don’t charge the battery when the battery is heated after use. Otherwise, it may cause the battery to expand, change, explode or even catch fire, threatening the safety of life and property. To dispose of the battery, please recycle the battery in strict compliance with the waste disposal laws and regulations of local countries or regions in order not to pollute the environment.|
FORBIDDEN
Away from moist environments
The interior of the aircraft is also composed of many sophisticated electronic components so it must absolutely be kept away from moisture or water vapor. Don’t operate the aircraft in the bathroom or on rainy days; otherwise water vapor may get inside of the aircraft and cause mechanical parts and
electronic components to malfunction leading to expected accidents.|
FORBIDDEN
Never misuse the product
Please do not disassemble or modify the product. For any upgrade, repair or maintenance, please use the parts specified in our catalog to ensure the safety of the structure. Please make sure the product is used within the limits of operation. Don’t overload the product, and don’t use it in any other illegal ways than prescribed by safety concerns and laws.|
FORBIDDEN
Safe usage of the battery
Batteries are to be inserted with the correct polarity. The supply terminals are not to be short-circuited. Different types of batteries or new and used batteries are not to be mixed.
The exhausted batteries are to be removed from the toy. For long time storage, please take them
out to prevent battery leakage. Please dispose of abandoned batteries in accordance to the laws and
regulations of the corresponding region to prevent pollution to the environment.|
CAUTION
Keep away from source of heat
The aircraft is mostly made of PA fiber or polyethylene as well as other main materials for electronic products. Therefore, it must be kept from the source of heat and exposure to sunlight to avoid possible damage of deformation or even meltdown due to high temperatures.
|
WARNING
Never operate the product alone
This product is suitable for users over 14 years old. Since the remote-control quadcopter may pose
a certain degree of difficulty for learners at the beginning, it is recommended that it be operated under the guidance of experienced people for the sake of safe flight.
|

Description of WIFI Live Stream Camera Version
How to connect the WIFI signal

http://www.vison-st.com/app/download/attop_nano

Please confrim you chose the X-PACK 10 item, otherwise the app will not work.

1. Download the app: “Attop Nano” from App Store / Google Play.
2. Power on the drone.
3. Go to the WIFI setting on the phone/device, choose the WIFI signal of the drone (X-PACK-xxxxxx) , and connect it.
4. Select the item and click “Go to Connect”.
5. If you have any questions, please click “ ” to or scan the QR code or the email to leave message to customer service.

Attention: When it is low power of the drone, it might be unable to be connected successfully.

1.Home page
2.Gesture to take pictures
3.Up down mirror
4.Speed mode: 30%,60%,100%
5.360° Stunt
6.Headless mode
7.Gravity control
8.Path plan
9.Voice control
10.VR mode
11.Battery
12.Wifi signal
13.On/Off for interface
14.One key take off
15.One key landing
16.Calibration| 17.Ascend
18.Descend
19.Turn left
20.Turn right
21.Left joystick
22.Forward/Backward trimming
23.Forward
24.Backward
25.Left sideward
26.Right sideward
27.Right joystick
28.Sideward trimming
29.Emergency stop
30.Take video
31.Take picture
---|---

Operation ways
You can fly the drone separately with your device or your controller.
A. Control with your device.

1. After connecting the WIFI signal and entering to the app interface, click the ‘on/off button’ 13 to open it.

2. Wait for 2 seconds until the drone lights flash, then click the ‘Calibration button’ 16 to calibrate the drone.

3. Simultaneously control the app by pushing the Left Control Stick to lower left at 45°and the Right Control Stick to lower right at 45° until four propellers start rotating.

4. Click the ‘One key take off 14 to fly the drone, or you could slowly push the Left Control Stick forward at the app to take off.
   Click the ‘One key landing’ 15 (or keep pushing down the throttle directly) to land the drone.

5. Click the ‘Video’ button 30 to take video.
   Click the ‘Picture’ button 31 to take pictures.
   After shooting, you can review the files by the ‘Media’ in Home Page or by the album file of your device.

B. Control with the remote controller.
There’s no need to use your device to connect the WIFI, if you don’t use the drone for shooting.

1. Power on the drone and power on the controller, after pairing between the controller and drone (the lights of the drone and controller are turning solid), then connect the WIFI signal between your device and the drone.
2. Put the device to the clamp of the controller, then click “Go to connect”.
3. Press the ‘picture’ button at the app interface or on the controller to take pictures.
4. Press the ‘Video’ button at the app interface or on the controller to take video. After shooting, you can review the files by the ‘Media’ on Home Page or by your album file on your device.

Name of App: Attop Nano
Apply to IOS \ Android system
(Note: Apply to Android 2.3 or above such as SAMSUNG, SONY,
HUAWEI and etc. But it cannot guarantee the phone of other brands with Android system could operate stably.)
30-Day Whole Unit Warranty For Quality-Related Issue
For 30 days after the date of purchase, we take care of all quality-related issues with a REPLACEMENT.
Reminder : Be sure to operate your drone as directed.
90-Day Accessories Warranty For Any Reason
For 90 days after the date of purchase, we take care of all accessories quality-related issues with an ACCESSORY REPLACEMENT.
Reminder: Be sure to maintain your drone as directed.

Guangdong Attop Technology Co., Ltd.
Linghai Industry Zone, Laimei Road, Chenghai District, Shantou,
Guangdong, China.
Website: www.attoptoys.com
Customer Service Email : attop@afterservice.vip

References

• ATTOP TECHNOLOGY CO.,LTD.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>