Attop X-Pack 18 1080P FPV GPS Drones Instruction Manual

Attop X-Pack 18 1080P FPV GPS Drones

Product Information

Specifications

• Suitable for wide indoor environments operation and wind power less than Force 2 outdoor environments
• Suitable for 14 years old and above
• Flight time: about 9-10 minutes
• Charging time: about 120 minutes

Package Contents

• Drone X1
• Remote X1
• Backup Propellers X4
• USB cable X1
• Battery X2
• Screwdriver X1

Charging Guide

1. Connect the USB cable with a power supply. The USB LED will light up, indicating the cable is powered on.
2. Connect the battery with the USB cable. If the USB LED stays solid, the charging is completed. Otherwise, it means the battery is charging. Please use the drone when fully charged.

Note: Use a power supply with a standard output voltage of 5V and a current greater than or equal to 2A to avoid overloading the USB cable and battery.

Installation

1. Open up all four blades of the drone.
2. Insert the battery into the specified position in the remote controller.
3. For mobile device holder usage, pull up the position of the controller and adjust the mobile device holder. Place the mobile device onto the holder.

Remote Controller Functions

• Speed switch
• Left stick (Altitude Control / Turn L/R)
• Power switch
• One key take-off
• Circle Fly
• One key landing
• One key return
• Headless function
• Right stick (Movement control)
• Gyro calibration
• Forward trimming
• Right trimming
• Backward trimming
• Left trimming
• Filming
• Take Photo

Product Usage

1. Switch on the power by pressing the power button on the drone and remote controller.
2. Perform frequency pairing by pushing the left stick on the remote controller to the top and then down to the lowest position.
   • After 2 seconds, the indicator lights on both the drone and controller will go steady, indicating successful frequency pairing.
3. Perform gyroscope calibration by pressing the calibration button on the remote controller. This step helps stabilize the aircraft during flight.
4. To activate the motors for taking-off, push the left stick to the lowest left corner and simultaneously push the right stick to the lowest right corner. The motors of the drone will start rotating.
5. To take off, press the one-key take-off button on the remote controller or push up the left stick directly. To land, press the one-key landing button or keep pushing down the left stick.

FAQ (Frequently Asked Questions)

• Question: What is the flight time of the drone?
• Answer: The flight time is about 9-10 minutes.
• Question: How long does it take to charge the battery?
• Answer: The charging time is about 120 minutes.
• Question: What age group is this drone suitable for?
• Answer: This drone is suitable for individuals aged 14 and above.

Package Contents

Charging

Low battery warning

When the drone is flying, the indicator lights on the drone are flashing, and the remote control handle emits a “beep” alarm sound, indicating that the drone power is too low. At this time, the drone needs to be returned and charged.

Charging Guide for battery

1. Connect the USB cable to the power supply, and the USB LED is solid on, indicating the USB cable is powered on.
2. Connect the battery with a USB cable. If the USB LED is solid, the charging is completed. Otherwise, it means charging. Please use the drone when fully charged.

Note: Use a power supply with the standard output voltage of 5V and current greater than or equal to 2A, otherwise there is a risk of overloading the USB cable and Battery. The flight time is about 9-10 minutes and the charging time is about 120 minutes.

Install

1. Open Up all 4 blades for the drone
   • This aircraft is a folding structure, please open up all four propellers before taking off.
2. Battery Installing

Remote Controller:

Insert 3xAAA battery into the specified position.

1. Insert the battery into a specified position.
2. To disassemble, press the battery buckle button, and pull it back to take it out.
3. Mobile Device Holder Using
4. Pull up the position of the controller.
5. Adjust the Mobile Device Holder up and place the mobile onto the holder.

Remote Controller

1. Speed switch
2. Left stick (Altitude Control / Turn L/R)
3. Power switch
4. One key take-off
5. Circle Fly
6. One key landing
7. One key return
8. Headless function
9. Right stick (Movement control)
10. Gyro calibration
11. Forward trimming
12. Right trimming
13. Backward trimming
14. Left trimming
15. Filming
16. Take Photo

How To Fly

1. Switch On the Power
2. First power on the drone (Keep pressing for 2-sec and place it on a flat ground or surface.)
3. Power on the Remote
4. Frequency pairing
   • After powering on the drone, both indicator lights on the drone and controller are flashing. Push the Left stick to the top, and then down to the lowest, after 2 seconds, the indicators will go steady, which means the frequency paired successfully.
5. Gyroscope calibration
   • Press the Calibration button for the gyro calibration. (For the aircraft to fly more stable operate this step before activating motors every time).
6. Activate motors for taking off
   • Push the Left stick to the lowest left corner, and meanwhile push the right stick to the lowest right corner, (Or just push the left stick to the top) then the motors of the drone start rotating.
7. Take off / Landing

• After activating the motors, press “One key take off” (or push up the Left stick directly) to fly. Press “One key landing” (or keep pushing down the Left stick directly) to land.

Emergency Stop

• In case of emergency status, push the Left stick to the right corner, meanwhile push the Right stick to the left corner at the same time, and the drone will immediately stop and drop off.

Using the Remote Controller

Aircraft Functions

TRIMMING ON THE FLYING ACTIONS

• Adjustment for deviated flying to  Front/Backward
• If it leans forward, press the down trimmer. If it leans backward, press the up trimmer.
• Adjustment for deviated flying to sideward If it leans left, press the right trimmer.
• If it leans right, press the left trimmer.

360° Flip Function

1. Short press the Right Stick
2. Push the stick to the right, the drone will rotate 360° toward the right direction
3. Short press the Right Stick
4. Push the stick to the top, the drone will rotate 360° toward the front direction.
5. Short press the Right Stick
6. Push the stick to the left, the drone will rotate 360° toward the left direction.
7. Short press the Right Stick
8. Push the stick to the bottom, the drone will rotate 360° toward a back direction.

Speed Adjustment

The drone is set to low speed by default.
Press the Speed button to change the speed gear while flying. There are 3 gears, each gear has a “beep” notice voice, the default speed is the most slowly one when pressed one time you will hear a “beep beep”, then go into the second speed gear, and press again with “beep beep beep” to the final fastest speed.

Remark: Beginners would be suggested to use the default speed first to play until skillful.

Take photos / Filming

• Press the Filming button to start and press again to finish and save the video. Please make sure to open the app on your smartphone before using it, then you can review the videos taken in the media file of the app or your mobile image file.
• Press the Take Photo button. Please make sure to open the app on your smartphone before using it, then you can review the photos taken in the media file of the app or your mobile image file.
• Note : The Video and Take Photos switch is only for the WiFi version.

Headless Mode Function

• Press the Headless function button, when the indicator lights slowly flash, which means it is in Headless Mode.
• Press the Headless function button again, when the indicator lights stop flashing, which means deactivating Headless Mode.
• Users are recommended to stay in the same orientation as the drone head is facing when the drone takes off.
• Under Headless Mode, the forward direction is the direction that the head of the drone faces when the drone takes off.
• To make sure the users can tell the drone’s direction, we suggest that users stay in the same orientation as the drone facing when it takes off.
• Then no matter which direction the head is facing, the drone will lock the controlled direction as the remote controller, easy to control back the drone.

One key return

• The remote toward the tail of the drone and presses the button, then the drone will fly toward its back following a path parallel to the remote direction. The LEDs on the drone keep flashing when the drone is returning.
• Press the button again or move the Right Control Stick, forward to cancel this function, or the drone will keep flying back.
• Note: Please deactivate the Headless function and make sure the remote is toward the tail of the drone before activating the Return function.

Aircraft Parameters

• Length of main wing: 152mm
• Aircraft: 190X226X73mm
• Total weight: 148g±2g
• Battery: 3.7V 1100mAh
• Charging time: About 120 mins
• Flight time: 9-10 mins
• Gyroscope: built-in
• Working temperature: -10°C to 40°C
• Remoter controller: 2.4G
• Motor: 85X20 4pcs

Camera Parameters

• TF card support: NO
  Camera Lens: 1080P

Remote Controller Parameters

• Wifi Transmission Range: 60-80 meters
  • (in a wide open area with no electromagnetic interference)
• Working frequency: 2.4G
• Battery: 3xAAA

FAQ

and drone (please refer to P.4 for details)

2| No response after the battery is inserted into the drone| 1. Check if the power for the remote and drone is fully charged.

2. Connection of the poles is not good

| . Open the remote battery case and make sure the battery is inserted in the right position

2.  Use a fully charged battery

3.  Reinstall the battery and confirm whether it is connecting with the poles well.

3| The motor does not run when operating the throttle stick and the indicator lights on the drone keep flashing|

Power for the Li-Poly battery is not enough

| Charge the battery or replace it with a

full-charged battery

4| The main motor blades spin but the drone won’t fly| 1. Some of the blades have been deformed

2. Battery power is not enough

| 1. Replace the main blade

2. Charge the battery or replace it with a fully charged battery

Battery Using Attention

Matters needing attention

1. Rechargeable batteries are to be removed from the toy before being charged.
2. Non-rechargeable batteries are not to be recharged.
3. Rechargeable batteries are only to be charged under adult supervision.
4. Only used to charge 2S Li-ion or Li-polymer battery packs. if not, the charger or battery may be damaged.
5. During charging, the charger should be put in a dry and ventilated place and far away from heat sources and inflammable and explosive substances.
6. Never immediately charge your battery pack as soon as the flight is finished, or when its temperature doesn’t cool down. Otherwise, the battery will take the risk of swelling, even a fire.
7. Ensure the correctness of polarity before connecting the battery to the charger.
8. Avoid drop and violence during the process of charging. drop and violence will result in an internal short circuit of the battery.
9. For the sake of safety, please use the original charging equipment and battery pack. please change new one in time when the flying time is becoming shorten due to long time usage.
10. If it is retained in the charger for a long time after saturated, the battery may automatically discharge. When the charger detects that the voltage of individual cells is lower than the rated voltage, it will recharge until saturated. Frequently charging and discharging will shorten the lifetime of your battery pack. It is advised that please cut off the power and take off the battery after the charging is saturated.

Maintenance of battery pack

1. The battery pack should be put in a dry and ventilated place. The storage temperature of the environment is ranged from 18°C to 25°C.
2. Please avoid frequent charging and excessive discharging of the battery pack to prolong its life cycle.
3. It is a must to maintain the battery pack before long-term storage. That is to charge the battery to the level of 50-60% saturation.
4. If the storage term is over 1 month, it is advised to monthly check the voltage of every cell of the battery pack. The voltage of every cell should be not less than 3V. Otherwise, please refer to the above article （3）.
5. From the viewpoint of protection, a new battery pack should be motivated before usage. That is to charge and discharge 3-5 times, but discharge is not less than the level of 70% saturation. This process will make the battery lifetime longer and the voltage more stable.

SAFETY AND PRECAUSTIONS

Disclaimer

• Please read this manual carefully before using our product.
• This product is not recommended for people under the age of 14. By using this product, you hereby agree to this disclaimer and signify that you have read it fully. You agree that you are responsible for your conduct and any damage caused while using this product, and its consequences. You agree to use this product only for purposes that are proper and under local regulations, terms and all applicable policies and guidelines ATTOP may make available.

Description of ATTOP GO drone WIFI Version

This version of the drone comes with the WIFI Live Stream Camera.

SCAN, AND DOWNLOAD APP

How to connect the WIFI Signal

1. Download the app “ATTOP CLUB ” from the App Store / Google Play.
2. Power on the drone.
3. Go to the WIFI setting on your phone/device, choose the WIFI signal of the drone (X-PACK 18+No.), and connect it.
4. Now open the app the drone, and Slip to Select The Drone “X-PACK 18” and then enjoy playing it.

Attention: When the drone is at the status of low battery, it might be unable to be connected successfully.

After connecting the WIFI signal between the drone and mobile device, and opening the APP, we can Select The Drone “X-PACK 18” and see the screen as the image above.

1. Enter the Interface of this drone after selection.
2. Media Folder: After taking photos and videos, you can review them from this folder.
3. Ascend / Descend / Turn left / Turn right
4. Go forward / Go backward / Left side flying / Right side flying
5. Gesture control
6. Music
7. Speed mode: 30%,60%,100%
8. 360° flip
9. Headless mode
10. Gravity Control (press it to perform this function, by changing your action of shaking the device to control the drone flying)
11. Flight path mode
12. Voice control
13. VR mode
14. Return home page
15. On/Off for control interface
16. Switch to take a video
17. Switch to take the photo
18. Go Forward / Backward trimmer
19. Left / Right side flying trimmer
20. EMERGENCY STOP !!!
21. One key take-off
22. One key landing
23. Calibration

Ready to fly

1. After connecting the WIFI signal and entering into the operation interface, press the “ON/OFF button” to open the sticks.
2. Wait for 2 seconds till the lights of the drone stop flashing then press the “Calibration button” to calibrate the drone if first time play.
3. Push the Left Control Stick to the top and then release. Now the rotors of the drone start rotating, which activates the motors.
   • (see pic 1)
4. Press the “One Key Take Off ” to fly up the drone (or push up the Left Contol Stick slowly), to take off. Press the “One Key Landing” (or keep pushing down the Left Control Stick directly) to land the drone.

APP operation method

1. Ascend / Descend / Turn left / Turn right
2. Go forward / Go backward / Left side flying / Right side flying
3. Gesture control
4. Music
5. Speed mode: 30%,60%,100%
6. 360° flip
7. Headless mode
8. Gravity Control: Switch “Gavity Sense Mode and wave the mobile phone as in the image shown below, the drone will move in the same direction movement.
9. Flight path mode: Press and you can draw a flying route plan on the screen, the drone will fly according to the route you designed.
10. Voice control: Unlock the motors and the rotors of the drone start rotating, then press and say “Take off ” / “Landing” / Forward” / “ Backward” / “Left side” / “Right side” six voice instructions, the drone will reflect correspondent actions.
    • Note: The APP needs your access allowance to use the microphone when first activating this function.
11. VR mode: Suitable for VR glasses use.
12. Return home page
13. On/Off for control interface
14. Switch to take a video
15. Switch to take the photo
    • After taking photos and videos, you can review them from
    • Home page Media Folder or your album file on your mobile device.
    • Note: The APP needs your access allowance to the phone album when first activating this function.
16. Go Forward / Backward trimmer
17. Left / Right side flying trimmer
18. EMERGENCY STOP: In case of an emergency, the drone will immediately stop functions and drop off.
19. One key take-off
20. One key landing
21. Calibration

Control with the remote controller (IF your drone with controller)

1.  Power on the drone and power on the remote, after pairing the frequency between the remote and drone (the lights of the drone and controller become permanent), then connect the WIFI signal between your device and the drone.
2. Put the device to the clamp of the remote controller, then go to the app interface to play the FPV flying.
3. Press the “Picture” button on the interface or a controller, to take the picture. Press the “Video” button on the interface or the controller, to take a video. After taking you can review the files from the media folder, or the album file of your device.

Name of App: ATTOP CLUB

• Apply to IOS \ Android system (Note: Apply to Android 2.3 or above such as SAMSUNG, SONY, HUAWEI, etc. But cannot guarantee the phone of other brands with Android system could operate stably.)

30-Day Whole Unit Warranty For Quality-Related Issues

• For 30 days after the date of purchase, we take care of all quality-related issues with a REPLACEMENT.
• Reminder : Be sure to operate your drone as directed.
• 90-Day Accessories Warranty For Any Reason
• For 90 days after the date of purchase, we take care of all accessories quality-related issues with an ACCESSORY REPLACEMENT.
• Reminder: Be sure to maintain your drone as directed.
• www.attoptoys.com
• Customer Service Email:support@attoptoys.com
• Get 24/7 assistance at Use the camera or QR scanner to scan Or Visit:https://attop.afterservice.vip

References

• ATTOP TECHNOLOGY CO.,LTD.
• afterservice.vip

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>