Attop X-PACK 10 Quadcopter Mini RC Drone User Manual

June 12, 2024
Attop

Attop X-PACK 10 Quadcopter Mini RC Drone User Manual

Attop X-PACK 10 Quadcopter Mini RC Drone User Manual

https://attop.afterservice.vip
www.attoptoys.com
attop@afterservice.vip

1. Aircraft Parameters

Length of main wing: 83mm
Aircraft: 98X120X33mm
Total weight: 54g±2g
Battery: 3.7V 380mAh
Charging time: About 50 mins
Flight time: 7-8 mins
Gyroscope: built-in
Working temperature: 14°F to 104°F
Remote controller: 2.4G
Motor: 7*16 4pcs

2. Remote Controller Parameters

Wifi Transmission Range : 30-40 meters
(in a wide open area with no electromagnetic interference)
Working frequency: 2.4G
Battery: 3xAAA

3. Package Contents

Attop X-PACK 10 Quadcopter Mini RC Drone User Manual - Package
Contents

4. Charging

  • When the drone’s battery is low, there are continuous beeps from the controller and the drone’s LEDs keep flashing.
  • Please use the original battery and USB cable provided.
  • Keep the battery away from any sharp objects that could puncture into the battery to avoid risks of explosion and fire.
  • It’s not recommended to charge the battery from the USB port of PC.
  • Flight time may be reduced when flying in low-temperature environments.

⚠ Note: Please fully charge the battery before flying.

5. Remote Controller

  1. Phone Clamp
  2. Left Control Stick
  3. ON/OFF
  4. One Key Take-Off/Landing
  5. Circle Fly
  6. Headless Mode (short press) One Key Return (long press)
  7. High-Speed Rotation
  8. LED Indicator
  9. Right Control Stick
  10. Drone’s LED Indicators
  11. Forward Trim
  12. Rightward Trim
  13. Backward Trim
  14. Leftward Trim

6. Installation

Attop X-PACK 10 Quadcopter Mini RC Drone User Manual -
Installation

  • a. Loosen the screws, then remove the cap.
  • b. Take out the propellers.
  • c. Fit the spare propellers into the drone according to the mark (A/B) on them.
  • d. Install the cap and tighten the screws.

⚠ Note: Please do not overtighten the screws. Gently rotate the propellers by hand after installation to check whether they are rotatable, if not, please loosen the screw and check again.
Attop X-PACK 10 Quadcopter Mini RC Drone User Manual -
Installation

7. How to Fly

Attop X-PACK 10 Quadcopter Mini RC Drone User Manual - How to
Fly Attop X-PACK 10
Quadcopter Mini RC Drone User Manual - How to Fly

8.Using the Remote Controller

Attop X-PACK 10 Quadcopter Mini RC Drone User Manual - Using the Remote
Controller

FLIGHT OPERATION GUIDE
IMPORTANT

  • Make sure that you power on your drone first, and then turn on the controller before each flight.
  • Please repeat the pairing and calibration procedure each time while the drone or controller is restarted.
  • For all flight functions and modes, the operator and tail of the drone must be aligned.

9. Aircraft Functions

(1) Speed Switch
The drone is set to low speed by default.
Press the button once for medium speed and there are two beeps from the controller. Press it again for high speed and there are three beeps from the controller.

Press it the third time to get back to low speed and there is one beep from the controller.

(2) Headless Mode
Short press the button to activate Headless Mode; LEDs on the drone start flashing.
In this mode, the drone will fly following the direction of the Right Control Stick regardless of the position of your drone’s head or tail.

Press the same button to exit this mode; LEDs on the drone turn to solid on.

(3) 360° Flip
Fly the drone to a height over 2m, then press the button to activate 360° Flip function. Next, move the Right Control Stick to flip the drone accordingly.

Attop X-PACK 10 Quadcopter Mini RC Drone User Manual - Fly the drone to a
height over 2m

Note:

  • There are continuous beeps from the remote when you activate this function. If you do not move the Right Control Stick about 5s after you press the button, the function will be cancelled and the remote will stop beeping.
  • This function can’t be activated when the battery of the drone is low.

(4) One Key Return
a. Press and hold the button, then the drone will fly toward its back following a path parallel to its original take-off path. The LEDs on the drone keep flashing when the drone is returning. b. Press and hold the button again or move the Right Control Stick forward to cancel this mode, or the drone will keep flying back.

Attop X-PACK 10 Quadcopter Mini RC Drone User Manual - One Key
Return

(5) High-Speed Rotation
Press the button to make the drone rotate at high speed. Press the button again or move the Right Control Stick to any direction to exit this mode.

Note: This function can’t be activated when the battery of the drone is low.

(6) Circle Fly
In the case of barrier-free within 5m radius around the drone, press the button to fly the drone in a circle. Press the button again or move the Right Control Stick to any direction to exit this mode.

Note:
This function can’t be activated when the battery of the drone is low.

(7) Photo / Video Please connect the drone to your mobile device first, then go to the `Media’ in app Home Page or your album file of the device to check your photos and videos.
Press the button to take a photo.
Attop X-PACK 10 Quadcopter Mini RC Drone User Manual -
Photo

Note:
It’s NOT recommended to use this function during normal flight for landing, which may result in serious damage for your drone.

(8) Altitude Hold/Hover
This is one of the default settings of the drone. When you release the Left Control Stick after an ascent/descent action, the drone will hover at the current flight height. For a stable flight, press the trim buttons to adjust accordingly.

(9) Emergency Stop
Press and hold the button, then the drone will stop in the air and fall.

10. FAQ

Attop X-PACK 10 Quadcopter Mini RC Drone User Manual -
FAQ

11.Battery Using Attention

Matters needing attention

  1. Rechargeable batteries are to be removed from the toy before being charged.

  2. Non-rechargeable batteries are not to be recharged.

  3. Rechargeable batteries are only to be charged under adult supervision.

  4. Only used to charging 2S Li-ion or Li-polymer battery pack. if not, the charger or battery may be damaged.

  5. During charging, the charger should be put in the dry and ventilated place and far away from heat source and inflammable and explosive substance.

  6. Never immediately charge your battery pack as soon as the flight is finished, or when its temperature doesn’t cool down. Otherwise the battery will take a risk in swelling, even a fire.

  7. Ensure the correctness of polarity before connecting the battery to charger.

  8. Avoid drop and violence during the process of charging. Drop and violence will result in internal short circuit of the battery.

  9. For the sake of safety, please use original charging equipment and battery pack.
    Please change new one in time when the flying time is becoming shorter due to long time usage.

  10. If it is retained in the charger for a long time after saturated, the battery may automatically discharge. When the charger detects that the voltage of individual cells is lower than the rated voltage, it will re-charge until saturated. Frequently charging and discharging will shorten the lifetime of your battery pack. It is advised that please cut off the power and take off the battery after the charging is saturated.

Maintenance of battery pack

  1. The battery pack should be put in the dry and ventilated place. The storage temperature of environment is ranged from 64.4°F to 77°F.
  2. Please avoid frequent charging and excessive discharging the battery pack in order to prolong its life cycle.
  3. It is a must to maintain the battery pack before long-term storage. That is to charge the battery to the level of 50-60% saturation.
  4. If the storage term is over 1 month, it is advised to monthly check the voltage of every cell of the battery pack. The voltage of every cell should be not less than 3V. Otherwise, please refer to the above article (3).
  5. From the view point of protection, new battery pack should be motivated before usage.
    That is to charge and discharge 3-5 times, but discharge is not less than the level of 70% saturation. This process will make the battery lifetime longer and voltage more stable.

SAFETY AND PRECAUSTIONS

Attop X-PACK 10 Quadcopter Mini RC Drone User Manual - SAFETY AND
PRECAUSTIONS Attop
X-PACK 10 Quadcopter Mini RC Drone User Manual - SAFETY AND
PRECAUSTIONS

Description of WIFI Live Stream Camera Version
How to connect the WIFI signal

Attop
X-PACK 10 Quadcopter Mini RC Drone User Manual - QR Codehttp://www.vison-st.com/app/download/attop_nano

  1. Please confirm you chose the X-PACK 10 item, otherwise the app will not work.
  2. Download the app: “Attop Nano” from App Store / Google Play.
  3. Power on the drone.
  4. Go to the WIFI setting on the phone/device, choose the WIFI signal of the drone (X-PACK-xxxxxx) , and connect it.
  5. Select the item and click “Go to Connect”.
  6. If you have any question, please click ” ” to or scan the QR code or the email to leave message to customer service.

Attention: When it is low power of the drone, it might be unable to be connected successfully.

Attop X-PACK 10 Quadcopter Mini RC Drone User Manual - Product
Overview

  1. Home page
  2. Gesture to take pictures
  3. Up down mirror
  4. Speed mode: 30%,60%,100%
  5. 360° Stunt
  6. Headless mode
  7. Gravity control
  8. Path plan
  9. Voice control
  10. VR mode
  11. Battery
  12. Wifi signal
  13. On/Off for interface
  14. One key take off
  15. One key landing
  16. Calibration
  17. Ascend
  18. Descend
  19. Turn left
  20. Turn right
  21. Left joystick
  22. Forward/Backward trimming
  23. Forward
  24. Backward
  25. Left sideward
  26. Right sideward
  27. Right joystick
  28. Sideward trimming
  29. Emergency stop
  30. Take video
  31. Take picture

Operation ways
You can fly the drone separately with your device or your controller.
A. Control with your device.

Attop X-PACK 10 Quadcopter Mini RC Drone User Manual - Operation
ways

  1. After connecting the WIFI signal and entering to the app interface, click the `on/off button’ 13 to open it.
  2. Wait for 2 seconds until the drone lights flashing, then click the `Calibration button’ 16 to calibrate the drone.
  3. Simultaneously control the app by pushing the Left Control Stick to lower left at 45°and the Right Control Stick to lower right at 45° until four propellers start rotating.
  4. Click the One key take off’ 14 to fly the drone, or you could slowly push the Left Control Stick forward at the app to take off. Click theOne key landing’ 15 (or keep pushing down the throttle directly) to land the drone.
  5. Click the Video’ button 30 to take video. Click thePicture’ button 31 to take pictures.
    After shooting, you can review the files by the `Media’ in Home Page or by your album file of your device.

B. Control with the remote controller.
There’s no need to use your device to connect the WIFI, if you don’t use the drone for shooting.

  1. Power on the drone and power on the controller, after pairing between the controller and drone (the lights of the drone and controller are turning solid), then connect the WIFI signal between your device and the drone.
  2. Put the device to the clamp of the controller, then click “Go to connect”.
  3. Press the `picture’ button at the app interface or on the controller to take pictures.
  4. Press the Video’ button at the app interface or on the controller to take video. After shooting, you can review the files by theMedia’ in Home Page or by your album file of your device.

Name of App Attop Nano
Apply to IOS Android system (Note: Apply to Android 2.3 or above such as SAMSUNG, SONY, HUAWEI and etc. But it cannot guarantee the phone of other brands with Android system could operate stably.)

Guangdong  Attop Technology Co., Ltd.
Linghai Industry Zone, Laimei Road, Chenghai District, Shantou, Guangdong, China.
Website: www.attoptoys.com Customer Service Email : attop@afterservice.vip

30-Day Whole Unit Warranty For Quality-Related Issue For 30 days after the date of purchase, we take care of all quality-related issues with a REPLACEMENT.
Reminder : Be sure to operate your drone as directed.

90-Day Accessories Warranty For Any Reason For 90 days after the date of purchase, we take care of all accessories quality-related issues with an ACCESSORY REPLACEMENT.
Reminder: Be sure to maintain your drone as directed.

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals