XINYIFA HY100 Smart Projector User Manual

XINYIFA HY 100 Smart Projector

Safety Instructions

Read all instructions before you use this device. Do not make any changes or create settings that are not described in this manual. If physical damage, loss of data or damage is caused by failure to follow instructions, the warranty does not apply.

Setup

1. To reduce the risk of fire or electric shock, do not expose the device to rain or moisture. Objects filled with liquids, such as vases, should not be placed on this device.
2. Do not place this device on soft surfaces such as tablecloths or carpets, otherwise the device could be a fire hazard.
3. Do not place this device in areas susceptible to excessive dust and dirt or near any appliance generating a strong magnetic field.
4. To prevent overheating, do not block or clog the ventilation holes.
5. Never place this device in a confined space. Always leave enough space around this device for ventilation.
6. Protect this device from overexposure to direct sunlight, heat, large temperature fluctuations and moisture. Avoid extreme temperatures. The suitable operations and storage temperature for this device and its accessories is (0°F to 95°F).
7. When this device is running for a long period of time, the surface may become hot. Shut it down immediately and unplug the charger. Resume operation after this device has cooled down.
8. Always handle this device with care. Avoid touching the lens. Do not allow children to handle the device without supervision.
9. Never place heavy or sharp objects on this device.
10. To avoid electric shock the device.
11. Use attachments or accessories specified by the manufacturer only.
12.  Avoid extreme vibration as it may damage the internal components.

The following safety instructions ensure the long service life of the projector to avoid fire or electric shock. Please read carefully and pay attention to the following warnings.

• Don’t install the projector in sites with improper ventilation.
  

• Don’t install the projector in hot and humid sites.
  

• Don’t install the projector near the temperature and smoke transducer. lt may cause a sensor failure.

• Don’t install the projector in sites with direct blowing of warm and cool air-condition wind.

• Don’t cover the projector ventilation holes with any material.

• Don’t install the projector in dust and smoke sites.

• Don’t look into the lens when the projector is working, otherwise it may hurt your eyes.

• Please keep the projector away from water or any other liquid as it is not water pro

Notice

1. Please use the power cable with caution to avoid unduly bending. A damaged power cable may cause electric shock.
2. Please use the projector with caution to avoid dropping or shocking, which may damage the internal components.
3. Please use the same power voltage as marked on the projector.
4. Please use the projector in a dark room for the best results.
5. Please do not disassemble the projector by yourself, otherwise the warranty will be void.
6. Please turn off and unplug from the power supply if not using the projector for a long time.

Package List

• Projector × 1
  

• Remote Control × 1 (Batteries are not included)
  

• Projector User Manual × 1

• Power Cable × 1

• HDMI Cable × 1

• Clean Tool × 1

Overview

Tips:

1. Blurry Image
   • Go to setting – Display – Turn on the Auto Keystone Correction or enter Manual Keystone to adjust the image.
   • Press the focus button on remote control to get the best clarity.
2. Mounting Hole
   Adopting a single mounting hole dual-use design, the projector is compatible with the standard camera tripod and 1/4 inch screw projector tripod stand.

Remote Control

Attention:

1. Do not submerge the remote control in the water.
2. Do not put the remote control near fire or in wet or hot places.
3. Do not use old and new batteries together in the remote control.
4. lease take the batteries out if not using the remote control for a long time to avoid battery leakage.
5. lease point the remote control toward the IR receiver.
6. Please use the remote control within 6 meters distance and 30 degree angle.

Power On/Off

1. Power on: When the projector is power-off, press and hold the power button on the projector or the remote control for 2s to power on the projector.
2. Power off: When the projector is power-on, short press and hold the power button on the projector or the remote control to choose shutdown / reboot.

Getting Started

1. Plug the power cable to the projector
   

2. Press power button to turn on the projector.
   

3. Connect projector to HDMi port support device.
   

4. Use the manual focus by pressing the “Focus” button on the remote control.

5. Press the power button to turn off the projector.
   

Tips:
Make sure the projector is horizontal to the projector screen.

 FCC Statement

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Caution: Any changes or modifications to this device not explicitly approved by manufacturer could void your authority to operate this equipment.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

RF Exposure Information
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator and your body.

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>