Guangdong Attop Technology W Pro Camera Drone Instruction Manual

**Guangdong**

14 aqe
Instructions For Use
(Please keep and read this manual carefully before using this product)

W Pro
www.attoptoys.com

DISCLAIMER & WARNING

1. Please read this Disclaimer & Warning and Safety Guidelines carefully before using our product. This product is not recommended for people under the age of 14. By using this product, you hereby agree to this disclaimer and signify that you have read it fully. You agree that you are responsible for your own conduct and any damage caused while using this product, and its consequences. You agree to use this product only for purposes that are proper and in accordance with local regulations, terms, and all applicable policies and guidelines ATTOP may make available.
2. When using this product, please be sure to strictly abide by the specification requirements and safety guidelines stated in this document. Any personal injury property damage, legal disputes, and all other adverse events caused by the violation of the safety instructions or due to any other factor WILL NOT be ATTOP’s responsibility.

SAFETY GUIDELINES

Check Before Use:

1.  This product is a high-precision drone that integrates various electronic stability and control mechanisms. Please be sure to set up this drone carefully and correctly to ensure safe, accident-free operation.
2. Please be sure that the batteries of the drone and transmitter are clean, undamaged, and, fully charged.
3. Please be sure that all the propellers are undamaged and are installed in the correct orientation.
4. Please do a thorough check of the product before each use. Inspect the integrity of the parts, any signs of cracks and wear of the propeller, battery power and effectiveness of the indicator, etc. If after doing a complete check any issues are found, please refrain from using the product until the issue has been resolved.

Flight Environment:

Avoid flying over or near obstacles, crowds, high voltage power lines, trees, the South pole, and the North Pole, the base station. DO NOT fly near strong electromagnetic sources such as power lines and base stations as it may affect the onboard compass.
Don’t use this drone in adverse weather conditions such as rain, snow, fog, and wind.

Operation Requirements:

1. Please don’t use this product to follow any moving vehicles.

2. During the flight, only turn off the motor in case of an emergency.

3. As the battery becomes low return the drone back to your starting point

4. This product should not be used while drinking alcohol, if you are feeling fatigued, taking medicine, or feeling any physical discomfort.

5. Beware of the noise volume the drone produces. Keep your distance to avoid ear damage.
   

6.   Stay away from the rotating

7. Don’t fly in the No-Fly Zone. propellers and motors.

Use of Battery:

1. Please ensure batteries are fitted in the correct orientation as shown in the instruction manual.
2. Avoid short circuits by fitting the batteries incorrectly, and do not crush or squeeze the batteries as this could carry the risk of an explosion.
3. Do not mix new and old batteries as this can lead to poor performance of the product.
4. Dispose of used batteries carefully, do not litter.
5. Please keep dead batteries away from heat and fire.
6. If the device is not going to be used for an extended period of time, remove batteries to prevent potential damage from battery leakage.
7. it is recommended to only use the USB charging cable that comes with the drone to charge the battery.
8. Don’t connect the battery directly to wall outlets or car cigarette -lighter sockets.
9. Don’t attempt to disassemble or modify the battery in any way.
10. Don’t use the battery if it gives off an odor, generates heat becomes discolored or deformed, or appears abnormal in any way. If the battery is in use or being charged, remove it from the device or charger immediately and discontinue use.
11. Don’t pierce the battery casing with a nail or other sharp object, break it open with a hammer, or step on it!
12. Always charge the batteries in a fireproof container and away from combustible materials.
13. Don’t charge on surfaces that can catch fire. This includes wood, cloth, carpet, or in the application’s device.
14. Don’t immerse the battery in water or allow it to get wet.
15. Don’t solder the battery terminal directly.
16. Keep the battery out of reach of children or pets.
17. Don’t short-circuit the battery by connecting wires or another metal object to the positive and negative(-) terminals.

| Li-Po Battery Disposal & Recycling
Waste Lill in-polymer batteries must riot be placed with household trash. Please contact the local environmental or waste agency or the waste agency or the supplier of your model or your nearest Li-Po battery recycling center.|
---|---|---

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help
  Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
  This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

RF Exposure Warning Statements:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment shall be installed and operated with a minimum distance of 20cm between the radiator & body.

MAINTENANCE

1. Clean the product after each use with a clean, soft cloth.
2. Avoid prolonged exposure to direct sunlight and avoid the buildup of heat on the drone.
3. This device is not waterproof and must not be submerged in water under any circumstance. Failure to maintain the device completely dry will result in the failure of the unit.
4. Check the charging plug and other accessories for signs of damage frequently. If any part of the device is damaged, refrain from flying until maintenance can be carried out

PACKAGE CONTENTS

DRONE’S DETAILS

TRANSMITTER DETAILS

Transmitter Functions

• GPS Mode Switch
  When turning on the transmitter, the default mode is the GPS Mode. Turn off GPS by pressing the GPS switch. Check the icon ” ” on the App interface to confirm GPS status.

• Return to Home
  Press the button to start the RTH, the transmitter makes a “beep beep” sound per 1.5 seconds and the drone will fly back to the recorded Home Point. Press the RTH button again to exit the RTH procedure and regain control of the drone.

• Unlock/Lock
  Press the button “ ” then the motor will rotate. Pull the LeftJoystick to the bottom position. The motor will stop rotating and the drone MI be locked.

• Photo/ Video
  Press the button and the camera icon  ” camera takes one photo. Press the same button, the video icon ” ” on the Controller, the ” on the Controller, the camera will take the video. Press again will exit shooting.

• Speed Switch
  Low speed is the default setting before speed change. Press the button ” on the Controller and you will hear a beep, which means the drone is at a low speed. Press the button ” ” again and you will hear two beeps, which means the drone is at the high speed.

Controller Operation

INSTALLATION

Drone Battery

Installation: Push the battery into the battery compartment of the drone. Make sure that you hear a click sound indicating the battery is firmly installed.
Attention: The battery should be installed firmly, failure to do so may affect the flight safety of your drone. The drone may crash due to power-cut during the flight.

Removal: As shown above, press and hold the lock on both sides of the battery at the same time to remove the battery.

Install TF Card

As shown in the above figure. Please push the camera module out and insert the TF card ( Need to be purchased separately J to TF card slot, then you could hear “Click” , which means insert successfully. Push the camera module into the specified position of the drone.

1. Please operate carefully for avoiding damage to the camera module.
2. The original pixel pictures and videos will be stored in the TF card.

Transmitter Battery

1. Connect the USB cable to a USB socket such as a mobile power supply.
2. Connect the remote controller with a USB cable, and the LED of the controller is turned solid in Green means Charging status. If the LED of the controller is oft, means Charging is completed..

Note: The voltage of the power supply is no greater than or equal to 5V, otherwise there is a risk of overloading the USB cable. The charging time approx 45 mins

Propellers

Installation

The drone will not fly unless the correct propeller is installed on the correct motor shaft. See the illustration above. An “A” or “B” is printed on the back of each propeller. Lock the propeller to the motor shafts with screws rotating each screw clockwise.
Removal
For propellers, removal uses a screwdriver (provided) to rotate counter-clockwise and remove propellers.

Phone Holder

1. pull down the 1 position of the controller.
2. Adjust the Mobile Device Holder to hold tightly for the mobile device.

CHARGING

1. Connect the USB cable to a USB socket such as a mobile power supply (Use a power supply with a standard output voltage of 5V and current greater than or equal to 24 And then connect the battery with a USB cable, the LED of the battery is flashing, means charging. When four LEDs on the battery are bright and go steady, means Charging is completed.
2. The charging time of a single battery is 4.5-5.5 hours.

• Before charging, please check the contents of the ” Use of Battery” section of the ” Safety Guidelines” carefully!
• This product is only equipped with a single battery, you can choose to buy another battery to experience a longer flight.
• Use a power supply with a standard output voltage of 5V and current greater than or equal to 2A, otherwise, there is a risk of overloading the USB cable.

OPERATION GUIDE

Download APP

|
---|---
https://apps.apple.com/cn/app/w-gps/id1514763409| https://play.google.com/store/apps/details?id=com.vison.macrochip.w.gps

Scan the OR code, corresponding to either App StoreTM or GoogleTM Play Store and download the ” W – GPS ” application for free. Required Operating Systems: iOS v8.0 and later/ Android v4.3 and later
Unfolding the Drone

To unfold the drone follow the steps below.
Step 1: Unfold the front arms.
Step2: Unfold the rear arms arid and place the drone on a flat, level surface. The Head should face forward.
CONTACT US
Please do not hesitate to contact us if you need further support. cs@attoptoys.com

1. Short press and then long-press the Power Switch approx 2 seconds, and the LEDs on the battery are fully bright and the drone makes a sound, which means the drone is powered on, and place it on a level surface with the head forward.
   Connect your smartphone to the Wi-Fi network created by the drone. Check the drone’s status in the “W – GPS” App.

2. Your smartphone will launch a search of the available Wi-Fi networks:

3. Select the Wi-Fi network: W PRO-4K-**.

4. Wait for several seconds until your smartphone connects to the Wi-Fi network of the drone. This connection is generally represented by the Wi-Fi logo appearing on your smartphone’s screen.

5. Launch the W – GPS application. > The connection between your smartphone and the drone will be established automatically.

Pairing

After connecting the WiFi signal between the smartphone and drone. Turn on the switch on the transmitter. Once the transmitter sends out a “Beep” sound, it means that the drone has been successfully paired with the transmitter.
Calibrating the Compass
After the pairing operation, the LED lights of the drone are sharp-flashing, which that means is beginning compass calibration.
Step 1: Now, the APP interface displays the diagram. Hold the drone horizontally and rotate the drone in approx 3 complete circles. When completed the transmitter sends out a “Beep” sound and the LED lights of the drone flash slowly.
Step 2 : Now, the APP interface displays the diagram. Hold the drone vertically and rotate the drone in 3 complete circles. When completed the transmitter sends out a “Beep” sound and the LEDs lights of the drone turn solid.
Attention:

• If the GPS receives a signal from 7 or more satellites the rear LEDs of the drone will flash twice per second.
• Every time the drone is powered on the compass calibration should be performed.

Gyroscope calibration
Now, the APP interface displays the diagram. Place the drone on the level surface. The LED lights of the drone will flash rapidly for about 3 seconds. When completed, the front and rear lights turn solid. Or press the Gyroscope calibration switch “ on the remote control. The LED lights of the drone will flash rapidly for about 3 seconds When completed, the front and rear lights turn solid.

Unlocking the Motor
Please unlock the motor before take-off.

Press the red button “ , and the motors rotate.

1. Unlock the motor function will be activated, base the GPS receives a signal from 7 or more satellites OR Indoor mode.
2. If you do not any operation approx 10 seconds after unlocking the drone, the motors will stop rotating.

Locking the Motor
Pull the Left Joystick to the bottom position. The motor will stop rotating and the drone will be locked. (Pic. 1 )

One-key Takeoff/ Landing

1. After unlocking the drone, press the “ ” button in the APP interface, then ” ” and the drone will automatically take off and hover at 1.5m altitudes. Or press the button ” – again for take-off after unlocking the motors.
2. When the drone is flying, press the ” ” button, and the drone will fly back to the Home point and automatically land on the ground.

Tips:
Before flying, make sure the GPS Mode is turned on in case the drone gets lost!

FUNCTION DETAILS

Camera Angle Adjustment

During the flight, you can dial the wheel left/ right to tilt the camera up/ down. (The gimbal has a 90° tilt range.)

Return to Home (RTH)

• The Return to Home function brings the drone back to the Home Point.
• The Home Point is the location at which the drone takes off. This location will be recorded as the Home Point.

Smart RTH
If the GPS signal is available (7 or more satellites reception) and the home point is recorded previously, press the ” ” button on the transmitter, then the drone will fly back to the Home Point. Exit the RTH mode by pressing the ” ” button again.
Failsafe RTH
If the GPS signal is available (7 or more satellites reception) and the home point is recorded previously. Failsafe Return will he triggered if the transmitter signal is lost for more than 6 seconds. 1 he drone will automatically start the return procedure and it will fly back to the. Home. Point. YOU can exit “Failsafe RI H” mode by pressing the “Return to Home” button or pushing the Throttle Joystick if the transmitter signal is recovered.

• During the Failsafe Return procedure, the drone can not avoid obstacles.
• The drone cannot Return-to-Home if the GPS signal is weak (the satellite’s number is less than 7).
• If there is no GPS signal or the transmitter signal has lost for more than 6 seconds, the drone will not Return-to-Home but it can descend slowly until landing on the ground and locking the drone.

Low Voltage RTH
When the drone’s lights flash slowly, the ” symbol is displayed on the APP interface, the First f ow Voltage RTH will be triggered. The transmitter will emit a “Beep, Beep, Beep” alert every S seconds. the drone will return automatically in the following two conditions: (At this time, the drone can only fly within a safe range of the height no more than 70m and a distance of no more than 30m .)
a. When the flight distance is more than 30m, the drone will fly automatically into the electronic fence (H 20m x D 30mJ and stay at the current distance, then exit the First Low Voltage RTH. If the flight distance is equal to 30m, the drone will stay the current distance, then exit the First Low Voltage RTH.

b. When the flight altitude is higher than 20m, the drone stays at current highs and fry automatic catty into the electronic fence (H 20m x D 30m). then exit the First Low Voltage RTH. If the flight altitude is lower than 20m, the drone will ascend to 20m and fly automatically into the electronic fence (H 20m x D 30m), then exit the First I ow Voltage RTH.

Image Positioning System

The Image Positioning System consists of a camera 0 module, which acquires the position information of the drone through visual images to ensure precise positioning and safe flight of the drone.

The Image Positioning System is typically used in the indoor environment and an altitude lower than 8m. It works best when the drone altitude is less than 5m.

1.  Fly fast at an altitude below 0.5m.
2. Flyover monochrome surfaces (like pure black, pure red, pure red, and pure green).
3. Flyover strong light reflective surfaces or surfaces are prone to reflection.
4. Fly over water or transparent object surfaces.
5. Flyover moving object surfaces (such as crowds, swaying juggles, and glass).
6. Fly over an area where the fight changes dramatically and rapidly.
7. Flyover surfaces are extremely dark (lux< 10) or extremely bright (lux> 10.000).
8. Fly over surfaces without clear textures.
9. Flyover surfaces with highly repeating textures (small grid brick in the same color).
10. Flying speed should be controlled not to be too fast. When the drone is I meter from the ground. the flying speed should not be over 2m/s. When the drone is 2 meters against the ground. the flying speed should not be over 3m/s

•  Keep sensors clean at all times.
• The vision system is only effective when [the drone is within the altitude range of 5 meters.
• Make sure that the light is bright enough and [the surfaces is with clear textures so that [the vision system can acquire the movement information through recognizing the ground textures.
• The vision system may not function properly when the drone is flying over water. low light ground and surfaces without clear patterns or textures.

APP OPERATION INSTRUCTION

Operation Interface

Setting Parameters

Click the ” ” icon to enter the setting interface (as shown in the figure above), you can sera limited flight range:

1.  Maximum flight distance: 60-3300 feet/ 20-1000 m.
2. Maximum flight altitude: 60-390 feet/ 20-120 m.
3. Maximum flight radius: 16-160 feet / 5-50 m. (The Point of Interest’s flight radius is set at 16 feet by default.) .
4. Beginner Mode (default setting): The default flight altitude is 100 feet.
   The default flight distance is 100 feet.
   You can also Start calibration the Gyroscope and Compass in the setting interface (as shown above).

Follow Me

When the Follow Me function is enabled. the drone will follow the GPS in your smartphone to follow you wherever you go.

1. Ensure the drone’s flight range is within 30m.
2. Click the” ” icon on the App interface and click ” ” to enter the Follow Me function then ” ” the drone will now follow the phone’s coordinates.
3. To exit Follow Me Mode. simply click the ” icon on the app interface again.

Common Issues:

1. follow Me mode may be difficult to activate if the phone’s GPS signal is too weak. This could be due to the signal loss from surrounding buildings, trees, or congestion horn loo many mobile phones in the area.
2. Use in an open area arid be mindful of your surroundings. The drone is NOT equipped with obstacle avoidance.

Waypoint flight

It is recommended to enlarge the map if you want to use Waypoint

1. Click the” icons on the app interface, then click ” ‘ to enter the Waypoint flight function.
2. Draw a fine on the map to create a path [Max 15 paths), click the” ” icon to submit the route, then ‘ ‘, and the drone will now fly along the path according to the points connected on the map.
3. Click the ” ” icon for deducting the path.
4. Exit the Waypoint flight mode by clicking the “ “.
5. If the flight path submission fails, you can choose lo re-submit or exit again.

• DO NOT fly the drone towards people, animals, or small/ fine objects (e.g. tree branches and power lines) or transparent objects (e.g. glass or water). • There may be some deviation between the expected and actual flight path.

Point of Interest

1.  Click the  ‘ icon on the App interface, and click’ then Ili dirtball to enter the Point of Interest function.

2. The drone will record its flight position the moment you enter this function as the point of interest. The drone will now continuously circle clockwise around the preset point. (The default radius is 5m. To change the point, please click “setting ” —”Flight Radius ‘tart ” to reset

3. To exit Point of Interest mode, simply click the” – icon on the app interface again.

Take Photo/ Video

1. Click C nu- icon to switch between photo and video mode.
2. When It lutter button is “, click once to take a photo.
3. When the shutter button is ” -, click once to start recording and click again to stop recording.
4. Click the “ft-icon to enter the Media for viewing Photo and Video.

When the IF card is not installed, the photos or videos will be stored directly in the APP photo album 1E1/4.31 and smartphone. Tips: . The APP needs your access allowance to your phone album when first activating this function.
When the TF card is installed, the photos or videos are stored in the TF card.

DRONE STATUS INDICATOR

The LED lights of the drone are flash rapidly| The drone is connected to the transmitter and begins Compass Horizontal Calibration.

The LED lights of the drone are flash slowly.| Compass Horizontal Calibration has been completed and begun Compass Vertically Calibration.

The front light turns solid blue, rear light turns solid Green.| Compass Calibration has been completed. No GPS signal or weak GPS signal.

The front light turns solid blue, Green rear light flashes twice per second.| Good GPS signal.

Front and rear lights Rash rapidly when pressing the calibration button.| Currently calibrating the Gyroscope.

Front and rear lights Rash slowly when Righting.| The First Low Voltage RTH will be triggered.

Front and rear lights flash rapidly when Righting.| The Second Low Voltage RTH is automatically triggered.

SPECIFICATIONS

DRONE
Model: W PRO
Weight: 520 g / 18.4 oz
Max Flight Time: Approx 30 minutes
Operating Temperature Range: 32′ to 104F
Dimensions: 115 x 175 x 80 mm (Folded) 785 x 225 x 80 mm (Unfolded)
DRONE BATTERY
Capacity 2500 rnAh
Voltage: I I .4 V
Battery Type: Li-Po
Energy: 28.5 Wh
Charging power: 34.2 W
Charging Temperature Range: 4 1. to I 04T (5° to 40t)
Charging Time: 4.5-5.5 hours

TRANSMITTER
Operating Frequency 2.4 GI-1z
MAX Transmission Distance: 1000m (outdoor and unobstructed)
Battery 3.7V 300 mAh.
Charging Time. Approx 45 mins
Operating Temperature Range: 32° to 104°F
CAMERA
Camera frequency 5 GHz

Video/ Photo Resolution: 4K

Lens: FOV 90′
FPV Distance: 800m (outdoor and unobstructed)

Photo: JPEG
Video: MP4
MAX Supported TF Cards: 64 GB (Not included)
Controllable Range: Pitch: -90° to 0°
Operating Temperature Range: 32′ to 104’F
USB CHARGING CABLE

Voltage: 5 V
Ampere: > 2 A

TROUBLESHOOTING

The drone is in the gyroscope calibration state. Please place the drone on an flat and level surface.
2| The drone cannot hover after takeoff and tilts to one side.| Place the drone on a flat, level surface and repeat the gyro calibration.
3| The drone vibrated in flight.| The propeller are damaged. Please replace the new propeller.
4| The drone could not be unlocked and the drone’s lights flashed.| The drone battery voltage is too low. Please fully charge the battery.

CONTACT US
Please do not hesitate to contact us if you need further support.
cs@attoptoys.com
BATTERY WARNING:

1.  failure to follow all the instructions may result in serious injury, irreparable damage to the battery and may cause a fire, smoke or explosion.
2. Always check the battery’s condition before charging or using it.
3. Replace the battery if it has been dropped, or in case of odor, overheating, discoloration, deformation or leakage.
4. Never use anything other than the approved LiPo charger the battery. Always use a balancing charger for Liro cells or a LiPo cell balancer. It is recommended that you do not to use any other charger than the one provided with the product.
5. The battery temperature must never exceed 60°C f I 40T) otherwise the battery could be damaged or ignite.
6. Never charge the battery on a flammable surface, near flammable products or inside a vehicle preferably place the battery in a non-flammable and non-conductive container.
7. Never leave the battery unattended during the charging process. Never disassemble or modify the housing’s wiring, or puncture the cells. Always ensure that the charger output voltage corresponds to the voltage of the battery. Do riot short circuit the batteries.
8. Never expose the LiPo battery to moisture or direct sunlight, or store it in a place where temperatures could exceed 60°C(car in the sun, for example).
9. Always keep it out of reach of children.
10. Improper battery use may result in a fire, explosion or another hazard.
11. Non-rechargeable batteries are not to be recharged. Rechargeable batteries are only to be charged under adult supervision.
12. Different types of batteries or new and used batteries are not to be mixed.
13. Batteries are to be inserted with the correct polarity.
14. The supply terminals are not to be short-circuited. Regular examination of transformer or battery charger for any damage to their cord, plug, enclosure and other parts and they must not be used until the damage has been repaired.
15. The packaging has to be kept since it contains important information.
16. The toy is only to be connected to Class II equipment bearing the symbol

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>