PERLEGEAR PGTVS29 Monitor Stand Instruction Manual

: June 16, 2024
: Perlegear

Table of Contents

PERLEGEAR PGTVS29 Monitor Stand Instruction
Product Information
Product Usage Instructions
BEFORE GETTING STARTED
SUPPLIED PARTS AND HARDWARE
INSTALLATION
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

PERLEGEAR PGTVS29 Monitor Stand Instruction

Product Information

Specifications

Model: PGTVS29
Max Load: 44 lbs (20kg)
VESA Pattern Compatibility: Minimum 50 x 50mm (2 x 2), Maximum 100 x 100mm (3.9 x 3.9)
Tools Needed (Not Included): Phillips Screwdriver, 3/8 (10mm) Wrench, 5/32 (4mm) Allen Key

Product Usage Instructions

Step 1: Compatibility Check
Check VESA Pattern Compatibility:
The VESA pattern compatibility for this stand is a minimum of 50 x 50mm (2 x 2) and a maximum of 100 x 100mm (3.9 x 3.9). Measure the distance between the mounting holes on the back of your TV to ensure compatibility. If your TV’s VESA pattern falls within this range, proceed to the next step. If not, contact our Technical Support or Customer Service for assistance.

Check Max Load:
This stand has a maximum load capacity of 44 lbs (20kg). Ensure that your TV weighs 44 lbs or less. If your TV weighs more than the specified maximum load, this stand is not compatible and should not be used.

WARNING: Exceeding the maximum load capacity can result in mount failure, which may cause damage or injury.

Tools Needed:
Gather the necessary tools for installation: a Phillips Screwdriver, a 3/8 (10mm) Wrench, and a 5/32 (4mm) Allen Key. These tools are not included with the stand.

Step 2: Attaching the Faceplate to Your TV
Before attaching the faceplate, determine the appropriate TV bolt size (M4, M5, or M6) that fits the threaded inserts on the back of your TV. Hand thread the bolts into the inserts, screwing in at least five turns without turning past the bottom of the hole.

Option A: For Flat Back TVs
If your TV has a flat back, follow these steps:

Add spacers, if needed, to fit the bolt length and TV back.
Use TV Bolt B1, C1, or D1 and Washer A1 or A2.
Optional: Spacer E can be used if necessary.
Do not overtighten the bolts.

Option B: For Curved Back TVs
If your TV has a curved back, follow these steps:

Select TV Bolt B2, C2, or D2 and Washer A1 or A2.
Use Spacer E or F to ensure the curved back does not interfere with the mounting plate.
Do not overtighten the bolts.

Option C: For TVs with a Bump
If your TV has a bump on the back, follow these steps:

Select TV Bolt B2, C2, or D2 and Washer A1 or A2.
Use Spacer E or F to level the faceplate on the bump.
Use TV Bolt B1, C1, or D1 and Washer A1 or A2 to fill the gap.
Do not overtighten the bolts.

FAQ

Q: What should I do if my TV’s VESA pattern is not compatible with this stand?
A: If your TV’s VESA pattern is not within the range of 50 x 50mm (2 x 2) to 100 x 100mm (3.9 x 3.9), please contact our Technical Support or Customer Service for assistance.
Q: Can I use this stand if my TV weighs more than 44 lbs (20kg)?
A: No, this stand has a maximum load capacity of 44 lbs (20kg). Using it with a TV that exceeds the maximum load can result in mount failure, which may cause damage or injury.
Q: What tools do I need for installation?
A: You will need a Phillips Screwdriver, a 3/8 (10mm) Wrench, and a 5/32 (4mm) Allen Key. These tools are not included in the stand.

Thank you for choosing this Perlegear product. We strive to provide you with the best quality products and services in the industry. If you have any installation questions or issues with the product, please contact us at the number below.

01 Tempered Glass Base
02a End Cap
02b Support Pillar
03 Faceplate
04 Plastic Cover
K Knob
Q Cable Clip
S Bolt
V1 Plastic Washer
V2 Steel Washer
W Foot Pad

BEFORE GETTING STARTED

LET’S MAKE SURE THIS STAND IS COMPATIBLE.

1

Check VESA Pattern Compatibility

| Measurement Conversion

Max: **** 50mm = 2″

3.9″

100mm **** 75mm = 3″

Max: **** 100mm = 3.9″

3.9″

100mm **Minimum:**

50 x 50mm (2 x 2″)

Maximum:

100 x 100mm (3.9 x 3.9″)

If this stand is not compatible, please contact our Technical Support line as listed above or Customer Service at support@perlegear.com.

---|---
2

Check Max Load

| WARNING

44 lbs DO NOT exceed the Max load

(20kg) **** indicated. Use with products heavier than the maximum load may result in

If your TV weighs more, **** failure of the mount,

this stand is NOT compatible. cause damage or injury.

3

Tools Needed (NOT Included)

| ****

4

Important Safety Information

| ****

• Please carefully read all instructions before attempting installation. If you do not understand the instructions or if you have any questions or concerns, please contact our Technical Support line as listed above or Customer Service at support@perlegear.com.

• Not all hardware included in this package will be used.

CAUTION: **** Avoid potential injuries and property damage!

• Do not use this product for any purpose that is NOT explicitly specified in this manual. Do not exceed the maximum load. We’re not liable

for damage or injury caused by incorrect assembly, improper mount- ing, or inappropriate use.

• Before starting assembly, check all parts are included and undamaged. Do not use damaged or defective parts. If you require replacement parts, please contact our Technical Support line as listed above or Customer Service at support@perlegear.com.

WARNING: This product contains small parts that may pose a choking hazard.

SAVE THESE INSTRUCTIONS.

SUPPLIED PARTS AND HARDWARE

INSTALLATION

STEP 1 ATTACHING THE FACEPLATE TO YOUR TV
SELECT TV BOLTS
Only one bolt size fits your TV.

Hand thread bolts into the threaded inserts on the back of your TV to determine which bolt (M4, M5 or M6) to use. We recommend screwing in at least five turns. Do not turn past the bottom of the hole.

SPACER AND BOLT CONFIGURATIONS

ATTACH THE FACEPLATE TO YOUR TV CAUTION: The lever should be positioned toward the top of the TV.

CHOOSE THE COMBINATION THAT APPLIES TO YOUR VESA HOLE PATTERN

50 x 50mm (2 x 2″)
75 x 75mm (3 x 3″)
100 x 100mm (3.9 x 3.9″)

OPTION A: FOR FLAT BACK TVS
Add spacers, if needed, to fit the bolt length and TV back.

OPTION B: FOR CURVED BACK TVS
Spacers must be tall enough so that the curved back of the TV does not interfere with the mounting plate.

OPTION C: FOR TVS WITH A BUMP
The faceplate must be flush on the bump and leveled by spacers on the gap.

OPTION D: FOR TVS WITH PROTRUDING CABLES
Use spacers to create extra space between the TV and the faceplate.

OPTION E: FOR TVS WITH RECESSED HOLES
Spacers need to fill in the recessed holes on the back of the TV, while keeping the faceplate as close to the TV as possible.

STEP 2 CONNECTING THE SUPPORT PILLAR TO THE BASE

Attach the foot pads [W] to the matte side of the tempered glass base [01].
TIP : Leave a small gap between the edge of the glass and the foot pads.
Secure the support pillar [02b] to the tempered glass base [01].

STEP 3 ATTACHING THE TV TO THE SUPPORT PILLAR

The support pillar has five height options. Choose the best height position for your TV 1 before moving on to attach your TV to the pillar.
Hang the TV on the support pillar [02b].
Secure the TV to the support pillar [02b] using the knob [K].

STEP 4 CABLE MANAGEMENT

STEP 5 SWIVEL ADJUSTMENT
The TV can be swiveled manually. Only swivel the TV by the TV edges. Do not press on the screen.

TIP : If the TV is difficult to swivel, remove the TV, then slightly loosen the preassembled nut. Do not overloosen. Reattach the TV and swivel.

STEP 6 ADJUSTING THE TILT ANGLE OF THE TV
Slightly loosen the lever [T]. Adjust the TV to your desired tilt angle. Retighten the lever [T] to lock the tilt angle.

CAUTION : DO NOT overtighten or over-loosen the lever.

STEP 7 LEVELING THE TV
Level the TV to your desired angle by hand

STEP 8 ROTATION
If the VESA holes on the back of your display are perfectly centered, you may rotate the display 360 degrees for portrait mode.

CAUTION : Only use portrait mode if the VESA holes on the back of your TV are perfectly centered. Rotating a TV with off-centered VESA holes may cause instability and lead to a tip-over accident.

THANK YOU FOR CHOOSING THIS PERLEGEAR PRODUCT

1-800-456-5231 (US/CA) Mon–Fri, 8am–8pm (CST) 44-808-196-4165 (UK) Mon–Fri, 2pm–10pm (UTC)
support@perlegear.com www.perlegear.com
860-01866-00 Rev01