PERLEGEAR PGTVMC07 Mobile TV Stand Installation Guide

PERLEGEAR PGTVMC07 Mobile TV Stand

INSTRUCTION FOR USE

Option A

Option A: For Flat Back TVs
Add spacers (if needed) to properly fit the threaded hole depth and bolt length.

Option B

Option B: For Curved TVs
Spacers must be tall enough so that the curved back of the TV does not interfere with the mounting plate.

Option C

Option D: For TVs with Protruding Cables
For protruding cables, use spacers [I] , [J] or [K] to create extra space between the TV and TV brackets.

Option E

Option E: For TVs with Recessed Holes
Spacers [I] , [J] or [K] need to fill in the recessed holes on the back of the TV, while keeping the TV brackets as close to the TV as possible.

STEP 2 Secure the Casters [02] on the Base [01]

Turn the base upside down to keep the bottom side of the base upwards.

Lock the casters [02], then secure the four casters [02] on the base [01].

Turn the base upside down again to keep top side of the base upwards.

STEP 3 Connect the Height Adjustable Post [03] to the Base [01]

Back Side

Fasten the four bolts [A2] using the Allen key [E2] to secure the height adjustable post [03] on the base [01]

STEP 4 Adjust the Height of Post

1. Unscrew the pre-assembled safety bolt [S] on right lower poles assembly using [E2] (6mm Allen key) and keep it for the use of Step 4-4.

2. Use left hand thumb or index finger to depress spring ball [S1] located at the right lower post (Near cable window), at the same time use right hand to twist and pull right upper post (Clockwise or anti-clockwise either directions will do) upwards to your desired height.
   

3. Use height label indicator on pole as guide. Then twist upper pole toward plunger holes direction and engaged spring ball [S1] into the plunger hole.

4. Secure safety bolt [S] firmly using [E2] (6mm Allen key). Please do the procedures from step 4-1 to 4-4 to pull out the left upper post.
   
   

STEP 5 Secure the Connecting Plate [06] and TV Plate [05] on Height Adjustable Post [03]

Caution: Ensure bolts are secured firmly.

STEP 6 Secure the TV to the TV Plate [05]

Hang the TV to the TV Plate.

Note: Kindly note that the TV should be hung in the center of the TV plate to keep balance.

Fasten the bolts [G2] via safety locks [F2] to secure the TV on the TV plate [05].

STEP 7 Secure AV Tray [08] to the Height Adjustable Post [03]

Attach the AV tray support [09] to AV tray [08].

Pull the AV tray supports [09] down to secure them to the AV tray [08], then put them to the holes on the AV tray [08] as shown.

Secure the fixing ring [10] to the AV tray support [09].

Attach the AV tray assembly to the height adjustable post [03].

Caution: Ensure bolts are secured firmly

STEP 8 Install the Webcam Tray Bracket [11] on the Connecting Plate [06]

1. Secure the webcam tray [12] on the top of webcam tray bracket [11] using the bolt [G2].
   

2. Remove the preassembled bolts [S3] from the connecting plate [06] and keep them for the use of step 8-3.
   

3. Attach the the webcam tray bracket [11] on the connecting plate [06] and tighten the bolts [S3] removed from 8-2.
   

STEP 9 TV Height Re-set and Cables Management

1. It needs 2 men to re-set the TV height, “A” man holds TV bottom with 2 hands as shown.

2. The “B” man simply unscrew 2 safety bolts [S] from left and right post using [E2] (6mm) Allen key Then depress 2 spring balls [S1] with his thumbs, so that ‘A’ man can adjust TV downwards or upwards to desire viewing height. Please note: you can use height label indicator on pole as reference.

3. When height is determined, put the spring ball set into plunger holes respectively, then secure 2 safety bolts [S] firmly as shown.
   

4. Attach the cable covers [04] to the cable windows.

5. Route cables and wires from upper cable windows to lower cable windows. Be caution when routing wires to avoid damage.
   

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>