nanoleaf NL64K000 Skylight Smart Modular Ceiling Light

Product Information

• Specifications
  • Product Name: Nanoleaf Skylight
  • Product Type: Smart Modular Ceiling Light

Product Usage Instructions

• Step 1: Mount the Main Controller Panel
  • Turn off the circuit power and the light switch.
  • To open the Main Controller Panel (A):
  • Pull the clear tape on the panel.
  • Insert a flathead screwdriver into one of the small notches along the seam. Slightly twist the screwdriver.
  • Remove the L L-shaped cover to reveal the terminal block for wiring.
  • Remove the Ceiling Plate by unscrewing the Wing Nuts (C).
  • If mounting with the Ceiling Plate:
  • Ensure that the wires are positioned through the hole of the plate with a suitable length visible.
  • Fasten the Ceiling Plate so that it is parallel to your desired panel alignment.
  • The Main Controller Power Wires (L) attached to the Main Controller Panel (A) can be connected with junction box wires using the included Binding Posts (H).
    • Black = Live 18AWG Input Wire
    • White = Neutral 18AWG Input Wire
  • Make sure the wires are secure and connected to the corresponding wires.
  • Position the Main Controller Panel (A) at the desired ceiling location and hold it against the ceiling.
  • Take a pencil and mark each screw hole on the ceiling.
  • Align and mount the Main Controller Panel (A) back to the Ceiling Plate.
  • Make sure the wires have passed through the Ceiling Plate and that the Main Controller Panel (A) sits secure and flat on the plate.
  • Secure the Ceiling Plate with the Wing Nuts (C).
• Frequently Asked Questions (FAQ)
  • Q: What should I do if I’m missing or have damaged parts?
  • A: If any items are missing or damaged, please reach out to our Customer Care Team at go.nanoleaf.me/support.
  • Q: Where can I find more detailed instructions?
  • A: For more detailed instructions, visit go.nanoleaf.me/myskylight.

Overview

• Read these instructions carefully and keep them for future reference. Refer to the What’s in the Box section for guidance, and ensure you have all the required parts before starting.
• When installing, place all parts on a soft, clean, flat surface such as a carpet to prevent scratches. If you’re having difficulty, please reach out to our friendly Customer Care team for help at go.nanoleaf.me/support.
• Installation should be performed by an individual with previous electrical experience.
• Consultation with a professional electrician is recommended for the installation of this product.
• Keep parts away from children.

Still Need Help?

• Visit go.nanoleaf.me/myskylight for more detailed instructions.

What’s in the Box

Ensure you have all the required parts before starting. If items are missing or damaged, please reach out to our Customer Care Team at go.nanoleaf.me/support.

Smarter Kit

Expansion Pack

Installation Instruction

Step 1: Mount the Main Controller Panel

• Before you start, turn off the power of your main circuit.
• Plan out your layout. Align and mark the panels of your desired layout on the ceiling.

• Turn the circuit power and the light switch o before you start.
• To open the Main Controller Panel (A)
  • A. Pull the clear tape on the panel.
  • B. Insert a flat head screwdriver into one of the small notches along the seam. Slightly twist the screwdriver.

Remove the L L-shaped cover to reveal the terminal block for wiring.

Remove the Ceiling Plate by unscrewing the Wing Nuts (C).

• If mounting with the Ceiling Plate, ensure that the wires are positioned through the hole of the plate with a suitable length visible.
• Fasten the Ceiling Plate so that it is parallel to your desired panel alignment.
• The Main Controller Power Wires (L) attached to the Main Controller Panel (A) can be connected with junction box wires using the included Binding Posts (H).
  • A. Black = Live
  • B. White = Neutral
• Make sure the wires are secure and connected to the corresponding wires.

1. Use the electric drill (Ø6mm) to break through the four knockout holes.
2. Position the Main Controller Panel (A) at the desired ceiling location and hold it against the ceiling.
3. Take a pencil and mark each screw hole on the ceiling.

• Now align and mount the Main Controller Panel (A) back to the Ceiling Plate.
• Make sure the wires have passed through the Ceiling Plate and that the Main Controller Panel (A) sits secure and flat on the plate.
• Secure the Ceiling Plate with the Wing Nuts (C).

1. Using the provided anchors and screws, mount your Main Controller Panel in place with the four knockout holes in the corner of each panel.
2. To mount the panel in place you can use:
   • A. Drywall Anchors (F)
   • I. Screw in the four Drywall Anchors (F) to the four spots you marked prior, OR
   • B. Plaster Anchors (G)
   • I. Drill a hole of 6mm (OD) then drive the Mounting Screw (E) into the Plaster Anchor (G).
   • Different mounting hardware will be required for installation on structural wood, concrete, and porous masonry surfaces. The correct items are widely available at hardware and home improvement stores.

Step 2: Connect Electrical Wiring

• Insert the ceiling wires into any of the slots on the terminal block. Use your finger or a screwdriver to push the clamps when inserting. Make sure the wires are secured in place such that they cannot be pulled out.
  • A. Black = Live (L)
  • B. White = Neutral (N)
• Remove any terminal block knockout holes as needed.

Step 3: Mount Expansion Panels

• Add an Expansion Panel (B) and position it next to the Main Controller Panel (A).
• Remove the knockout holes on all four corners, hold it against the ceiling and mark each screw hole with a pencil.
• For each Expansion Panel (B), repeat the steps for mounting found on Page 9.
  • A. Drywall Anchors (F)
  • Screw in the four Drywall Anchors (F) to the four spots you previously marked, OR
  • B. Plaster Anchors (G)
  • Drill a hole of 6mm (OD) then drive the Mounting Screw into the Plaster Anchor.

Step 4: Connect the Wires

• Thread the wires through the Grommet Cover to connect the Communication Linker (J) from the Main Controller Panel (A) to the Expansion Panel (B) through the linker slot.
• Attach the Power Wires (K) to the socket closest to the next expansion panel. Follow the embossed line and wire through the opening to the next panel where the Communication Linker is attached.
• Repeat this step for additional panels you add.

Step 5: Power On

• Turn the circuit power back on and turn the light switch on to power the panels.

• Your new Skylight panels will now power on at low brightness. Once the boot-up process is complete, the panels will gradually shift to full brightness to indicate that the system is ready for pairing.

• Reinstall the L L-shape cover.

Step 6: Pair with the App

1. Download the Nanoleaf App on iOS/Android.
2. Pair the device by scanning the printed pairing code on the main controller panel or the printed QR code on the Quick Start Guide.
3. Follow the in-app instructions to complete pairing*
   • Press the reset button on the Main Controller Panel if the app fails to find the device.
4. Once Skylight is paired to the app, you can now snap all the covers back on the panels. The clips should snap securely on all sides.
5. You’ve completed the installation. Enjoy the possibilities and control of your new Nanoleaf Skylight panels!

WARNINGS & CAUTIONS

Please read this safety information carefully and keep this document for future reference. Help articles and customer support are always available at https://nanoleaf.me/support.This Nanoleaf® product is not designed, certified, nor intended for use in enclosed locations that limit the flow of air and/or trap heat which contributes to an environment temperature over 40 degrees Celsius; emergency exits, emergency lighting, or other use cases involving critical systems for human safety; in conjunction with 3rd party devices that are not approved by Nanoleaf® for use with Nanoleaf® products; locations or use cases where there is a risk of electric shock; outdoor areas, regardless of weather conditions; wet conditions; as a floor covering or floor tiling; excessively humid areas; regions or countries other than that in which the product was intended for and certified for sale in. When using this Nanoleaf® product: This luminaire must be installed by a qualified electrician according to local rules and codes. Do not disassemble the device personally, as this will void the warranty and make the product unsafe for use. Suitable installation fastening methods should be employed to ensure the mounting points are not damaged when subjected to vibration and/or movement. While connected to the electrical supply of the building, line voltages will be present in the power supply, panels, and linkers, so do not place any metallic or conductive objects near any exposed metal contacts on any component. Do not clean the device with liquid or sprays when it is connected to power. Clean the panels with a soft dry cloth, and do not use harsh cleaning agents. Do not submerge any part of the device in water, or expose any part of the device to water. Do not attach the panels with any connector or device other than the original equipment manufactured by Nanoleaf®. The flexible cable and power supply cannot be replaced by another third-party product. If the cable is damaged, the entire controller and power supply should only be replaced with original equipment manufactured by Nanoleaf®. Using any non-approved replacement component will void the warranty and may present a serious safety hazard. The light source of this luminaire is not replaceable. When the light source reaches its end of life, the whole luminaire shall be replaced. Nanoleaf® light panels are primarily intended for decorative use, with an RGBW output function that can dim.

FCC INFORMATION

This device complies with part 15 of the FCC Rules; This device contains licence-exempt transmitters)/receivers) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s).
Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. this device must accept any interference received, including interference that may cause undesired operation.

This equipment should be installed and operated with a minimum distance of 20 cm between the radiator and your body.
NOTE: This equipment has been tested and found to comply with the limits of a Class B digital device, under part 15 of the FCC Rules and the Canadian ICES-003 Class B specifications. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used following the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna;
• Increase the separation between the equipment and receiver;
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected;
• Consult the dealer or an experienced radio/ TV technician for help.

MODIFICATION: Any changes or modifications not expressly approved by the grantee of this device could void the authority to operate the device.
FREQUENCY RANGE BLE: 2400-2483.5MHz, Max RF e.i.r.p power < 10 dBm.
Wi-Fi: 2412-2472 MHz, Max RF e.i.r.p power < 20 dBm

WARRANTY

Nanoleaf warrants that this device’s hardware components will be free from defects in material and workmanship for a period of two (2) years from the date of purchase, unless a different period is stated in or on the packaging of the product, based on up to 3 hours average working time per day/7 days per week, when used as directed (the “Warranty Period”). Notwithstanding the foregoing, the Warranty Period for all Energy Star-certified products is three (3) years from the date of purchase. This limited warranty only applies to the hardware components contained in the original packaging. This limited warranty does not apply to any software, even if packaged or sold with the hardware components. Nanoleaf does not warrant that the use of this device will be uninterrupted or error-free. If this device does not conform to this limited warranty, Nanoleaf will send you, at its election, a replacement device or refund your original price upon receipt of the returned device, register receipt and proof of purchase. Please reach out to our customer support to find out how to return the device. This limited warranty does not cover devices subject to accident, neglect, abuse, misuse or acts of God. REPLACEMENT OR REFUND IS YOUR SOLE REMEDY. EXCEPT TO THE EXTENT PROHIBITED BY APPLICABLE LAW, ANY IMPLIED WARRANTIES ARE LIMITED IN DURATION TO THE DURATION OF THIS LIMITED WARRANTY. LIABILITY FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES IS HEREBY EXPRESSLY EXCLUDED. Some states and provinces do not allow the exclusion of incidental or consequential damages, so the above limitation or exclusion may not apply to you. This limited warranty gives you specific legal rights, and you may also have other rights that vary from state to state and province to province. For full details visit https://nanoleaf.me/warranty.

CONTACT

• Nanoleaf Canada

  • 400 – 100 Front Street East

  • Toronto, ON
  • M5A 1E1, Canada
• Nanoleaf Europe SAS
  • 11 Rue de Lourmel
  • 75015 Paris
  • France
• Nanoleaf Europe SAS
  • P/A 4Eyes Ltd, Bay House, Cox Hill,
  • Perranporth, Cornwall, TR6 OAT
  • United Kingdom
• Nanoleaf Hong Kong
  • NanoGrid Limited

  • 1301-483A Castle Peak Road,

  • Kowloon, Hong Kong
• Model: NL64K000
• Rated Power: 19.5W
• Input: 120V AC 60Hz
• Color Channels: RGBCW Dual-White
• Contains FCC ID: 2AEWY-NL04A
• Contains IC: 20489-NL04A
• @nanoleaf
• @nanoleafofficial
• /thenanoleaf.
• Learn more at:nanoleaf.me.

References

• Customer Support | Nanoleaf » USA » Consumer IoT & LED Smart Lighting Products
• Nanoleaf Helpdesk
• Shipping, Returns & Warranty | Nanoleaf » USA » Consumer IoT & LED Smart Lighting Products

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>