PERLEGEAR PGFS09 Floor TV Stand Instruction Manual

FLOOR TV STAND
INSTRUCTION MANUAL
MODEL PGFS09

PGFS09 Floor TV Stand

Thank you for choosing this Perlegear product. We strive to provide you with the best quality products and service in the industry. If you have any installation questions or issues with the product, please contact us at the number below.

BEFORE GETTING STARTED, LET’S MAKE SURE THIS STAND IS COMPATIBLE.

1. Check VESA Pattern Compatibility Measurement Conversion
   100mm =3.9″ 300mm = 11.8″
   200mm =7.9″ 400mm = 15.7″
   Minimum:
   100mm x 100mm (3.9″ x 3.9″)
   Maximum:
   400mm x 400mm (15.7″ x 15.7″)
   If this stand is not compatible, please contact our Technical Support line as listed above or Customer Service at support@perlegear.com.

2. Check Max Load WARNING
   DO NOT exceed the Max load indicated. Use with products heavier than the Max load may result in failure of the mount, which could  cause damage or injury.

3. Tools Needed (not included)

4. Important Safety Information
   • Please carefully read all instructions before attempting installation. If you do not understand the instructions or if you have any questions or concerns, please contact our Technical Support line as listed above or Customer Service at support@perlegear.com.
   • Not all hardware included in this package will be used.
   CAUTION: Avoid potential injuries and property damage!
   • Do not use this product for any purpose that is NOT explicitly specified in this manual. Do not exceed the Max load. We’re not liable for damage or injury caused by incorrect assembly, improper mounting, or inappro- priate use.
   • Before starting assembly, check all parts are included and undamaged.
   Do not use damaged or defective parts. lf you require replacement parts, please contact our Technical Support line as listed above or Customer Service at support@perlegear.com.
   WARNING: This product contains small parts that may pose a choking hazard
   TIP-OVER WARNING
   Serious or fatal crushing injuries can occur from a tip-over accident.
   To help prevent a tip-over accident:
   • Never allow children to climb, stand, hang, or play on any part of the TV or TV Stand
   • Use tip-over restraints (not included) or anchors (not included) to attach the TV Stand to the wall.
   • Use of tip-over restraints may only reduce, but not eliminate risk of a tip- over accident.
   SAVE THESE INSTRUCTIONS.

SUPPLIED PARTS AND HARDWARE

NOTE: The washers, spacers, and bolts shown above are displayed in accordance with actual size.

INSTALLATION

STEP 1 ATTACHING THE TV BRACKETS TO YOUR TV
SELECT TV BOLTS
Only one bolt size fits your TV, Hand thread bolts into the threaded inserts on the back of your TV to determine which bolt (M4, M or M8) to use. We recommend screwing in at least five turns. Do not turn past the bottom of the hole.

SPACER AND BOLT CONFIGURATIONS

ATTACH THE TV BRACKETS TO YOUR TV **** The TV brackets should be EQUALLY CENTERED on your TV AND securely fastened in place.

OPTION A: FOR FLAT BACK TVS
Add spacers, if needed, to fit the bolt length and TV back

OPTION B: FOR CURVED BACK TVS
Spacers must be tall enough so that the curved back of the TV does not interfere with the mounting plate.

OPTION C: FOR TVS WITH A BUMP
The TV brackets must be flush on the bump and leveled by spacers on the gap. OPTION D: FOR TVS WITH PROTRUDING CABLES
Use spacers to create extra space between the TV and TV brackets. OPTION E: FOR TVS WITH RECESSED HOLES
Spacers need to fill in the recessed holes on the back of the TV, while keeping the TV brackets as close to the TV as possible.

STEP 2 ASSEMBLING THE BASE Note: The raised edge around the outside of the plate should face up.Attach the foot pads [J] to the bottom of the wood base.
TIP: Leave a small gap between the edge of the wood base and the foot pads.Attach the bottom cover [06] and lower support pillar [07] to the wood base using washers [C] and bolts [B].

STEP 3 ATTACHING THE SUPPORT PILLAR

STEP 4 SECURING THE TV PLATE TO THE SUPPORT PILLAR

Note: There are three choices for height adjustment. You can choose your desired height position while connecting the TV plate [10] to upper support pillar [09]

STEP 5 MOUNTING THE TV ON THE TV PLATE
The TV brackets have three sets of hooks. Choose the appropriate hooks before hanging your TV. The #1 hooks will position your TV lower, while the #2 hooks will add extra height.
The #3 hooks will position your TV the highest. Insert the safety locks [K] into the upward-facing hooks located directly below the horizontal TV plate. Tighten the bolts until they secure against the bottom of the TV plate.

STEP 6 CABLE MANAGEMENT STEP 6 SWIVEL ADJUSTMENT
If necessary, the TV can be swivelled manually. Only swivel the TV by gripping the TV edges. Do not press on the screen.

1-800-456-5231 (US/CA] 44-808-196-4165 (UK)
860-02004-00 Rev01
Mon-Fri, 8am-8pm (CST)
Mon-Fri, 2pm-10pm (UTC)
support@perlegear.com
www.perlegear.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>