MAXPEEDINGRODS LK-AB-F150 Air Helper Spring Leveling Kit Installation Guide

June 15, 2024
MAXPEEDINGRODS

MAXPEEDINGRODS logo LK-AB-F150 Air Helper Spring Leveling Kit
Installation Guide

LK-AB-F150 Air Helper Spring Leveling Kit

MAXPEEDINGRODS LK AB F150 Air Helper Spring Leveling
Kit

AIR SPRING KIT
INSTALLATION GUIDE

FIT FOR FORD F-I5O PICKUP
REAR AIR HELPER SPRING LEVELING KIT

AIR SPRING BAG KITT LIST

Mounting brackets

1| | 2X Upper
mounting
bracket A (Left
and Right)| 2| | 2X Upper
mounting
bracket B (Left
and Right)| 3| | 2X Lower
mounting bracket
---|---|---|---|---|---|---|---|---
4| | 1X Axle
strap| 5| | 2X Adapter
bracket| 6| | 3X Fastening
block
7| | 4X Rolling plate| 8| | 1X Sleeve| 9| | 2X Universal
nut M10*1.5

Air spring bog and Air line

10 2X Air spring bag 11 1X Air line Φ6*1(5m)

All Hardware kits

12| | 7X Carriage
bolt
M101.5187-80| 13| | 1X Carriage bolt
M101.5150-50| 14| | 1X Heat shield
---|---|---|---|---|---|---|---|---
15| | 1X Thermal
sleeve (910190mm)| 16| | 6X Zip tie(1905)| | | 2X 90°Air Hose
Fitting R21/8
17
18| | 2X Inflation
valve (with cap)| 19| | 4X Hex thin nut
M8
1(3mm)| 20| | 2X Anti-slip
gasket 98
21| | 2X Rubber
gasket-917972| 22| | 4X Hex head
screw M101.516| 23| | 2X Hex head 2
crew s M10 c1.535
24| | 4X Half round
head bolt
M101.533| 25| | 4X Hex bolt
3/8-24UNF20| 26| | 4X Hex bolt
M10
1.520
27| | 16X Hex nylon
nut M10
1.5| 28| | 22X Flat washer
M10| 29| | 4X Washer
M10
30| | 2X Flat washer M8| 31| | 2X Hoop band (990)| |

PRE-INSTALLATION INSTRUCTION

  • This product will not increase the load capacity of your vehicle.
  • Do not exceed the manufacturer’s recommended weight limit.
  • The installation process may require drilling, professional installation is recommended to ensure personal safety.
  • All modifications must be installed by qualified personnel and in compliance with your local modification regulations.

INSTALLATION GUIDE

MAXPEEDINGRODS LK AB F150 Air Helper Spring Leveling Kit -
fig1

ASSEMBLING THE AIR SPRING

MAXPEEDINGRODS LK AB F150 Air Helper Spring Leveling Kit - AIR
SPRING

REMOVING THE JOUNCE BUMPER

STEP 1. Raise the vehicle and support it using safety stands so that the axle can be safely dropped away from the frame, and the air spring assemblies can be put into position between the axle and frame.
STEP 2. Unbolt and remove the jounce bumper from the frame.MAXPEEDINGRODS LK
AB F150 Air Helper Spring Leveling Kit - BUMPER

NOTE :
NOTE:
You may need to cut it off or sand it down, so the bolt is flush to the bracket for some models.
STEP 3. Remove the original clip, then install the Universal nut (‘© of the Air spring bag kit list) into the frame for some early models.

INSTALLING THE UPPER BRACKET

STEP I. Attach the Upper mounting bracket A (‘Oo of the Air spring bag kit list) to the frame with bolts. And the slot hole in the middle goes to face toward inside the truck. STEP 2. Push the axle up so that the Upper mounting bracket B ( © of the Air spring bag kit list) can be bolted to the previous bracket(@Qof the Air spring bag kit list). Then tighten the nuts.MAXPEEDINGRODS LK AB F150 Air Helper Spring Leveling Kit - BUMPER
3

INSTALLING THE LOWER BRACKET

STEP 1. Placing the Lower mounting bracket ( of the Air spring bag kit list) on the axle. Then install the lower mounting bracket to the frame with washers and nuts. MAXPEEDINGRODS LK AB F150 Air Helper Spring Leveling Kit -
BUMPER 4

NOTE: This sleeve and axle strap are mainly used for the lower bracket on the passenger side.
STEP 2. For some models, you may need to install the Adapter bracket (5 of the Air spring bag kit list) with lower mounting bracket.MAXPEEDINGRODS
LK AB F150 Air Helper Spring Leveling Kit - BUMPER5 STEP 3. Place the Rolling plate (5 of the Air spring bag kit list) between the air spring bag and the lower mounting bracket, align the holes and lock them with bolts.

INSTALLING THE HEAT SHIELD (PASSENGER’S SIDE ONLY)

STEP1. Install the heat shield where it is closest to the passenger’s (right) side air spring.MAXPEEDINGRODS LK AB F150 Air Helper Spring Leveling
Kit - BUMPER7 NOTE : Must slide the air line protective sleeve over the air line near the exhaust port.

INSTALLING THE AIR LINES

STEP I. Cut the air line appropriately and push the hose into the fitting, then pull back and make sure it’s locked in place. MAXPEEDINGRODS LK AB F150
Air Helper Spring Leveling Kit - BUMPER8

STEP 2. Install the inflatable valve in a selected location, usually on the license plate at the rear of the vehicle.

CHECK AIR TIGHTNESS

  • Put some air into the air spring bag, then spray a soapy solution on all connections and valves while checking for exiting air bubbles.
    INSTALLATION COMPLETED
    WARNING

Cancer and Reproductive Harm
www.P65warnings.ca.govMAXPEEDINGRODS
logo Since 2006

Documents / Resources

| MAXPEEDINGRODS LK-AB-F150 Air Helper Spring Leveling Kit [pdf] Installation Guide
LK-AB-F150 Air Helper Spring Leveling Kit, LK-AB-F150, Air Helper Spring Leveling Kit, Spring Leveling Kit, Leveling Kit
---|---

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

MAXPEEDINGRODS User Manuals

Related Manuals