xiamen ATS2853 Bluetooth Module User Manual

xiamen ATS2853 Bluetooth Module

ATS2853 Bluetooth Module With ANT SPEC

Specifications

• Operating Frequency Band: 2.4GHz ~ 2.48GHz unlicensed ISM band
• Bluetooth Specification: V5.3
• Bluetooth Protocol: A2DP, AVRCP, HFP
• Output Power Class: Class 1
• Operating Voltage: Core: 1.2V, IO: 3.1V, BAT: 3.4V~4.3V
• Operating Temperature Range: -20°C ~ 70°C
• External Interface: UART, SPI, TWI, I2S TX/RX, IR, SD Card,USB, DMIC, SPDIF TX/RX

Product Usage Instructions

Step 1: Power Supply
Connect the module to a power supply with a voltage range of 3.4V to 4.3V. Ensure that the core voltage is set to 1.2V and the IO voltage is set to 3.1V.

Step 2: Connection Setup
To use the ATS2853 Bluetooth Module, establish a connection using one of the following interfaces:

• UART
• SPI
• TWI
• I2S TX/RX
• IR
• SD Card
• USB
• DMIC
• SPDIF TX/RX

Step 3: Audio Playback

The ATS2853 Bluetooth Module supports wireless audio applications such as MMC/SD Card audio playback, Bluetooth car audio units, and sound bars. Follow the specific instructions provided by your audio device or application to enable audio playback.

Step 4: Bluetooth Connection
To establish a Bluetooth connection, ensure that your device is compatible with Bluetooth V5.3. Pair your device with the ATS2853 Bluetooth Module and follow the instructions provided by your device to start the Bluetooth audio playback.

FAQ

Q: What is the operating temperature range of the ATS2853 Bluetooth Module?
A: The ATS2853 Bluetooth Module can operate within a temperature range of -20°C to 70°C.

Q: What are the supported Bluetooth protocols?
A: The ATS2853 Bluetooth Module supports A2DP, AVRCP, and HFP protocols.

Q: What is the maximum RF transmit power of the module?
A: The maximum RF transmit power of the module is not specified in the provided information.

XIAMEN COMFORT SCIENCE & TECHNOLOGY GROUP CO., LTD.

Features

• 32bit RISC processor Core, up to240MHz

• Internal 203KB RAM for data and program storage

• Internal 2MByte Nor flash

• Support 24MHz OSC with on-chip PLL

• Internal 32KHz RC oscillator

• 8-channel ordinary DMA, support for transmission in burst 8 mode

• Support Bluetooth V5.3, compatible with Bluetooth V5.0/4.2/4.2 LE/4.0/2.1 + EDR system

• Compatible with AVRCP Profile V1.6

• Compatible with A2DP Profile V1.3

• Compatible with HFP Profile V1.7
  Built-in stereo 24bit sigma-delta DAC
  DAC supports sample rate of 8k/11.025k /12k/16k/22.05k/24k/32k/44.1k/48k/88.2k/96 kHz

• Built-in stereo 20mW PA for headphone

• Built-in stereo 24bit sigma-delta ADC

• ADC supports sample rate of 8k/11.025k/12k/16k/22.05k/24k/32k/44.1k/48k/88.2k/96 kHz

• Support 3 pairs input 0/1/2; each pair can be formed as mix or differential input.

• Support 2 DMIC input

• I2S TX&RX support master and slave mode separately, and support sample rate of 192k/96k/48k/44.1k/32k/24k/22.05k/16k/12k /11.025k/8k

• Support SPDIF TX , SPDIF RX and CEC

• Rich Interfaces support: SD,MMC/eMMC,USB2.0FS, 2xUART, 2xTWI, 1xSPI, IR RX, 9xPWM, support LCD with 8bit CPU interface, 1/3Bias, SEG_LCD Driver,7/8pin LED

• 24 Programmable GPIOs, and 10 analog IOs can also configure as GPIOs.

• PCB Dimension:

• L27±0.1×W14±0.1×H25+0.1mm

Applications

• Wireless Audio Application
• MMC/SD Card Audio Playback
• Bluetooth car audio unit
• Sound Bar

ATS2853 BT Module With ANT

Bluetooth Audio Solution

Wireless Audio Applications MMC/SD Card Audio PlaybackX

Bluetooth car audio unit Sound Bar

Bluetooth V5.3

Application Diagram

Specifications

Bluetooth Protocol

| ****

A2DP,AVRCP,HFP

Output Power Class| Class 1
Operating Voltage| Core :1.2V, IO:3.1V, BAT:3.4V~4.3V
Operating temperate range| （-20 ℃ ~ 70℃）

External Interface

| UART,SPI,TWI,I2S TX/RX,IR,SD Card,

USB,DMIC,SPDIF TX/RX

Electrical Characteristics

Absolute Maximum Ratings

Parameter| Symbol| Min| Max| Unit
Temperature| Storage temperature (Tstg)| -55| +150| °C
ESD Stress voltage| VESD (Human body model)| 4000| —| V

Supply Voltage

| VCC/AVCC/SVCC| 2.7| 3.6| V
VD15| 1.0| 1.7| V
BAT| 3| 5| V

Input Voltage

| 3.3V IO| 2.7| VCC+0.2| V
ONOFF| –| 5| V
Recommended Power Supply

Supply Voltage| Min| Typ| Max| Unit
BAT (Li)| 3.3| 3.8| 4.5| V
VCC/SVCC| 3.0| 3.1| 3.6| V
AVCC| 2.9| 2.95| 3.25| V
VD15| 1.2| 1.5| 1.7| V
Regulators Maximum Output Current

Block Name| Output Voltage| Load Capacity
VCC| 3.1V| 300mA
AVCC| 2.95V| 40mA
SVCC| 3.1V| 100mA

Note: The output voltages are precisely within 2%.

AUDIO Features

Test Condition: Power BAT=3.8V, Analog audio output AOUTL/R, Load = 10K ohm,BW=20Hz ~ 20 KHz, Test equipment: AP2722.

DAC/ADC audio output performance chart:

Line in Input Mode:

Bluetooth Player Music Mode:

RF Characteristics

BT Protocols

| ****

A2DP/AVRCP/HFP

| A2DP1.3.2
---|---|---
AVRCP1.6.2
HFP1.7

Power Consumption

| A2DP| Typical : 18.1mA  NOTE1
HFP| Typical : 20.8mA  NOTE1
Sniff| Typical : 2.1mA     NOTE2
Standby| Typical : 20uA       NOTE3

NOTE

1. Vbat = 3.8V,10K load, related to SDK.
2. Vbat = 3.8V,BLE broadcast is on.
3. Vbat = 3.8V.

Basic Data Rate of Transmitter

Parameter| Condition| Min.| Typ.| Max.| Unit
Maximum RF Transmit

Power

| –| 4| 5.5| 6.8| dBm
RF Power Control Range| –| 2| 4| 8| dB
20dB Bandwidth for

Modulated Carrier

| –| –| 928|  | KHz

Adjacent Channel Transmit

| +2 MHz| –| –| -20| dBm
-2 MHz| –| –| -20| dBm
+3 MHz| –| –| -40| dBm
-3 MHz| –| –| -40| dBm

Frequency Deviation

| Δf1avg   Maximum| 140| 164.35| 175| KHz
Δf2max   Maximum| 115| 149| –| KHz
Δf1avg/Δf2avg| 0.8| 1.1| –| –
Initial Carrier Frequency

Tolerance

|  | -75| ±10| 75| KHz

Frequency Drift

| HD1 Packet| -25| ±10| 25| KHz
HD3 Packet| -40| ±10| 40| KHz
HD5 Packet| -40| ±10| 40| KHz
Frequency Drift Rate|  | -20| 3.8| 20| KHz/50us
Enhanced Data Rate of Transmitter

Parameter| Condition| Min.| Typ.| Max.| Unit
Relative Transmit Power| –| -4| -1.5| 1| dB
π/4 DQPSK max carrier

frequency stability |ω0|

| –| -10| ±3| 10| KHz
π/4 DQPSK max carrier

frequency stability |ωi|

| –| -75| ±5| 75| KHz
π/4 DQPSK max carrier

frequency stability |ω0+ωi |

| –| -75| ±4| 75| KHz
8DPSK max carrier

frequency stability|ω0|

| –| -10| ±3| 10| KHz
8DPSK max carrier

frequency stability|ωi|

| –| -75| ±5| 75| KHz
8DPSK max carrier| –| -75| ±5| 75| KHz
frequency stability|ω0+ωi||  |  |  |  |
---|---|---|---|---|---

π/4 DQPSK Modulation Accuracy

| RMS DEVIN| –| –| 20| %
99% DEVM| 99| 100| –| %
Peak DEVM| –| –| 35| %

In-band spurious emissions

| F > F0 + 3MHz| –| –| -40| dBm
F < F0 – 3MHz| –| –| -40| dBm
F = F0 + 3MHz| –| –| -40| dBm
F = F0 – 3MHz| –| –| -40| dBm
F = F0 + 2MHz| –| –| -20| dBm
F = F0 – 2MHz| –| –| -20| dBm
F = F0 + 1MHz| –| –| -26| dB
F = F0 – 1MHz| –| –| -26| dB
EDR Differential Phase

Encoding

| –| 99| 100| –| %
Basic Data Rate of Receiver

Parameter| Condition| Min.| Typ.| Max.| Unit
Sensitivity at 0.1% BER|  | –| -90| –| dBm
Maximum Input Power at

0.1% BER

|  | -20| –| –| dBm
 |  | –| –|  |

Adjacent Channel Selectivity C/I

| F = F0 + 1MHz| –| –| 0| dB
F = F0 – 1MHz| –| –| 0| dB
F = F0 + 2MHz| –| –| -30| dB
F = F0 – 2MHz| –| –| -30| dB
F = F0 + 3MHz| –| –| -40| dB
F = Fimage| –| –| -9| dB
Enhanced Data Rate of Receiver

Parameter| Condition| Min.| Typ.| Max.| Unit
Sensitivity at 0.01%

BER

| π/4 DQPSK| –| -90| –| dBm
8DPSK| –| -82| –| dBm
Maximum Input

Power at 0.1% BER

| π/4 DQPSK| -20| –| –| dBm
8DPSK| -20| –| –| dBm

Module Pin definitions

ATS2853 Module

Pin Configurations

voltage:3.1V

26| BAT| Power input| Battery Voltage input
27| GND| Power ground| Ground
28| ANGD| Analog ground| Ground for Analog circuit
29| AVCC| Power output| Power for Analog module, typical

voltage:2.95V

30| INPUT1R| Analog input| INPUT1 Right channel input
31| INPUT1L| Analog input| INPUT1 Left channel input
32| INPUT0R| Analog input| INPUT0 Right channel input
33| INPUT0L| Analog input| INPUT0 Left channel input
34| INPUT2R| Analog input| INPUT2 Right channel input
35| INPUT2L| Analog input| INPUT2 Left channel input
36| VRO| Analog output| Direct drive mode bias
37| VRO_S| Analog output| Direct drive mode bias
38| AOUTR| Analog output| Right channel output
39| AOUTL| Analog output| Left channel output
---|---|---|---
40| GPIO9| Bi-directional| General Purpose Input Output 9
41| GPIO8| Bi-directional| General Purpose Input Output 8
42| GPIO6| Bi-directional| General Purpose Input Output 6
43| GPIO5| Bi-directional| General Purpose Input Output 5
44| SVCC| Power output| Power Supply for Hosc
45| WIO1| Input| Wake up IO1 and LRADC2 input
46| WIO0| Input| Wake up IO0 and LRADC1 input

Circuit Diagram

Module Package Information

ATS2853 Module：

Power on sequence

Recommended keepout area information

• It is recommended to place it at the end of the printed circuit board .
• Clearance area size: the distance is greater than 2.5mm
• Do not place metal objects in front, left, right, up and down positions

PCB antenna radiation pattern

Antenna Gain

Active Test free space

Soldering recommendations

Document History

FCC Statement

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

Integration instructions for host product manufacturers according to KDB 996369 D03 OEM Manual v01

List of applicable FCC rules
CFR 47 FCC PART 15 SUBPART C has been investigated. It is applicable to the modular transmitter

Specific operational use conditions
This module is stand-alone modular. If the end product will involve the Multiple simultaneously transmitting condition or differentoperationalconditionsforastand- alonemodulartransmitterinahost,hostmanufacturerhavetoconsultwithmodule manufacturerfortheinstallationmethodinendsystem. 

Limited module procedures
Not applicable

Trace antenna designs
Not applicable

RF exposure considerations
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. T

Antennas
This radio transmitter ATS2853 has been approved by Federal Communications Commission to operate with the antenna types listed below, with the maximum permissible gain indicated. Antenna types not included in this list that have a gain greater than the maximum gain indicated for any type listed are strictly prohibited for use with this device.

Label and compliance information
The final end product must be labeled in a visible area with the following” Contains FCC ID: YMX-ATS2853 “.

Information on test modes and additional testing requirements Host manufacturer is strongly recommended to confirm compliance with FCC requirements for the transmitter when the module is installed in the host.

Additional testing, Part 15 Subpart B disclaimer
Host manufacturer is responsible for compliance of the host system with module installed with all other applicable requirements for the system such as Part 15 B.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>