1Mii ML100 Wireless Audio Adapter User Manual
- June 14, 2024
- 1Mii
Table of Contents
1Mii ML100 Wireless Audio Adapter
In the box
Product overview
Quick guide
Instructions
- Slide power switch to “ON” side, the adopter will outomoticolly enter the pairing mode (LED lights flashing red and blue)
- Activate the Bluetooth of the mobile phone or tablet, click “MLJOO/MLIOl” to connect, and wait for the pairing to succeed
- connect the adopter to the car 3.5mm audio In.
- Enjoy your music.
How to enter pairing mode?
- Press and hold the button for 2 seconds. adapter will enter the pairing mode. (LED lights flashing red and blue).
- Pair and connect two devices simultaneously?
- Pair with the first device by following the previous instructions in the 1nstallotlon diagram· sectlon.
- Pair with the second device.
- Long press the button again until the LED light flashes red and blue alternately to enter the pairing mode.
- Activate bluetooth on the second device and click “MUOO/MUOl” to pair
- After successfully paired with the second device, the first device wlll be disconnected. You need to manually click the “MLlOO/MLIOl” in the Bluetooth list of the first device to reconnect, than MLIOO/MLlOI pair with the two devices at the some time.
Note : You con only ploy music on one device at a time, so if you want to ploy music on the second device, you need to pause the music on the first device before plying it on the second device.
Charging method
- Plug in the charging cable to charge the adopter, and the LED will be steady red
- When the battery is fully charged, the LED indicator will turn off
How to reset the device?
If adopter cannot be connected or does not work normally, please refer to the
following methods to reset the device
- Press and hold the 7 button for about 10 seconds until the LED flashes purple for 3 times, and then the device will restart and clear the list of paired devices, and the factory settings will be restored successfully.
Product overview
The Bluetooth® word mark and logos ore owned by the Bluetooth SIG, Inc. and any use of such marks by lMii Ltd. is under license. other trademarks and trade names ore those of their respective owners.
FCC
This device complies with port 15 of the FCC rules.
Operation is subject to the following two conditions
- This device may not cause harmful interference, and
- This device must accept any interference.
Changes or modifications not expressly approved by lMii Ltd. will void the
user’s authority to open rote the equipment This equipment hos been tested
and found to comply with the limits for o Class B digital device, pursuant to
port 15 of the FCC Rules. These limits ore designed to pr011ide reasonable
protection against harmful interference in o residential ins1a11a1ion. This
equipment genero1es. uses and con radiate radio frequency energy and, if not
installed and used in accordance with the instructions. may cause harmful
interference to radio communications
However, there is no guarantee that interterence will not occur in o
particular Installation. If this equipment does cause hamaul interference to
radio or television reception. which con be determined by turning the
equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver
- Connect the equipment to an electrical outlet on a different circuit to that which the receiver is connected.
- consult the manufacturer or an experienced radio/TV technician for help.
This product, like other radio devices. emits radio frequency electromagnetic energy and operates within the guidelines found in radio frequency safety standards and recommendations. These standards and recommendations reflect the consensus of the scientific community and result from deliberations of panels and committees of scientists who continually review and interpret the extensive research literature.
Ce
- lMii Ltd. hereby declares that this product is in compliance with the essential requirements and other relevant provisions of Directive 2014/53/EU.
- The full test of the EU declaration of conformity is available at the following internet address: www.lmii.com
- In accordance with Article 10 (2) and Article 10 (70), this product is allowed to be used in all EU member states.
- Shenzhen 1Mii Technologies Limited
- Booon District. Shenzhen 51B100 China
FU lmpar1er
- eVotmoster Consulting GmbH
- Bettinastr. 30,60325 Frankfurt am Main. Germany
Warranty
Warranty service is limited to normal use. Any man-made damages such as from connecting to an unsuitable power source, using on unsuitable device, or not following the instructions, as well damages that did not occur during shipping. repairs and adjustments not approved by the company, damages from misuse, inattention, or improper installation may cause the warranty to be ineffective immediately. this warranty does not include shipping fees.
Disosal
Always disosal dispose of the used appliance at o recycling centre Do not dispose the used appliance together with household waste
- eVatmaster Consulting GmbH
- Bettinastr. 30
- 60325 Frankfurt am Main,Germany
- [email protected]
Scan the QR code to get more information.
- Operator: Ankbit International Limited
- Address: 45-51 Chatham Road South, Tsim Sha Tsui, Kowloon, Hong Kong
- Manufacturer : Shenzhen Ankbit Electronics Limited
- Address: Runfeng Industrial Parle, No. 4197 Booon Blvd .. Xixiong St, Baoon Dist., Shenzhen, Chino
- We hope you never have the need, but if you do, our servlce is friendly and hassle-free.
- 12,1 [email protected]
- web: www.lmii.com
- FCC ID : 2AUFR-RT236