CREALITY ENDER3V3 SE 3D Printer User Guide

ENDER3V3 SE 3D Printer User Guide

About the Power-on Guide and User Interface

First Printing

5.1 Filament Loading

1. Cut the front of the filament at Input the nozzle temperature on the break it off straight;
2. Lock the dip switch, and then Insert the Teflon tube screen and wait for it to heat up to the. target temperature;
3. Into the connector above the nozzle kit

5.2 LAN printing

• Install Crealtty Print slicing software by opening the random data on the USB flash disk.
• Log In to the official website to download for Installation: https://wwvaw.crealitycloud.com/software—firmware/sofware?type=7

The current It shall  terface s for reference only. Due to the cor bes ublect to the latest softviare/~firmware Ul publls inuous upgrading of functions, hed on the officlal website.

The current interface is for reference only. Due 1o the continuous upgrading of functions, It shall be subje re/~fimware Ul published on the official website.

The interface Is for reference only. Due to the cor upgrading of fur tinuou tions, it shall be subject to the latest software/~firmware Ul published on the official websi

5.3 USB flash disk Printing

1. Tips: 71 Keep the dip switch locked before printing 2)
2. For detalls on using the software, please refer to the slicing software user manual on the US8 flash disk.
3. Saved files must be placed In the root directory (not a subdirectory) of the USB flash disk.
4. It Is recommended to use Latin alphabet, numbers, and commoncharacters for the file names.
5. Do not Insert or remove the USB flash disk during the printing process.

The current interface is for reference only. Due to the continuous upgrading of functions, it shall be subject to the latest software/firmware Ul published on the official website.

Functional Specification

6.1 Filament Retreat
Method 1: Manual retract

Method 2: Auto retract

6.2 Auto extrude

Equipment Maintenance

7.1 Platform plate removal and maintenance

1. When printing Is finished, walt for the platform plate to cool before removing the printing platform with the model attached; b, Slightly bend the platform with bath hands to separate the model from the platform
2. If there are residual filaments on the platform plate, scrape them off lightly with a blade and print again.
3. If the first layer of the modl Is nat properly glued, It is recommended 10 apply solid achesive evenly on the surface of the platform plate before preheating for printing.

Tips:

1. Don’t bend too much for dally use to prevent deformation and unusability;
2. The printing platform is a perishable part, and It Is recommended ta replace It regularly to ensure that the firs layer of the model sticks properly.

7.2 Maintenance of screw rod and guide rail
Regularly lubricate and malntain the screw rod and quide rail areas with purchased lubricating grease.

Xquipment Parameters

Itallano/ Turk/ Fa*Li

Circuit Wiring

Due to the differences between different machine models, the actual objects and the images can differ. Please refer to the actual machine. The final explanation rights shall be reserved by Shenzhen Creality 3D Technology Co., Ltd.

FCC Statemen

FCC Caution:
Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
This device complies with part 15 of the FCC Rules. Operation Is sublect to the following two conditions: (1) This device may not cause harmful Iterference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
IMPORTANT NOTE:
Note: This equipment has been tested and found to comply with the limits for a Class 3 digital device, pursuant o part 15 of the FCC Rules. These limits are designed to provids reasonable protection against harmful Interference In a residential Installation. This equipment generates, uses and can radiate radio frequency energy and, If not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there Is no guarantee that interference will not occur In a particular instaliation. If this equipment does cause hammful interference to radio or television reception, which can be determined by tuming the equipment off and on, the user is encauraged o ry to carrect the Interference by one or more of the following measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver,
—Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
—Consult the dealer or an experienced radio/TV technician for help.
FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment.
This equipment should be installed and operated with minimum distance 20cm batween the radiator& your body.

SHENZHEN CREALITY 3D TECHNO LOGY CO.,LTD. Tate Pleor. Jr ecubora bu Rurcone, Mlehone Reed imac Gompsurity,
Monel steeet Lorooine District Scterzhen Ciby. China
Cfticlel Weliscste www.coreeity.com
Tel:+86755-85234565
E-Mail: cs@creality.com

Documents / Resources

| CREALITY ENDER3V3 SE 3D Printer [pdf] User Guide
2AXH6-ENDER3V3, 2AXH6ENDER3V3, ENDER3V3 SE 3D Printer, SE 3D Printer, 3D Printer, Printer
---|---

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>