ideal lux 8I306797 Jedi LED Bollard Light Instruction Manual
- May 15, 2024
- ideal lux
Table of Contents
ideal lux 8I306797 Jedi LED Bollard Light
PARTS
Floor lamp
LED 19W / 220~240V 50/60Hz
- 8021696306797 ANTRACITE
- 8021696293196 NERO
DIMENSION
FEATURE
ASSEMBLY INSTRUCTION
CARRY OUT THE OPERATIONS FOLLOWING THE PROGRESSIVE ORDER FOLLOW THE ASSEMBLY INSTRUCTIONS BY READING THE NUMERICAL PROGRESSION THE INSTALLATION OF THIS APPLIANCE MUST BE CARRIED OUT BY QUALIFIED PERSONNEL THE LIGHTING FITTING SHOULD BE INSTALLED BY A QUALIFIED ELECTRICIAN
THE SAFETY AND RELIABILITY ARE GUARANTEED ONLY WHEN INSTALLATION INSTRUCTIONS ARE PROPERLY FOLLOWED. PLEASE KEEP THIS INSTRUCTION SHEET FOR FUTURE REFERENCE
Non-replaceable light source: at the end of its life, the lamp must be disposed.
This product is provided with a light source with efficiency energy class of:
EAN| Light Source Model| Energy Efficiency Class| Light Source (mA)| Light
Source (V)
---|---|---|---|---
8021696306797| JEDI H120 3000K| E| 100 mA| 9 V DC
8021696293196| JEDI H120 3000K| E| 100 mA| 9 V DC
ICON LEGEND
-
Replaceable light source by an end-user.
-
Replaceable LED light source by an end -use.
-
Replaceable light source by authorized personnel only.
-
Upon end of life of the light source, the whole produce will be replaced.
-
Replaceable control gear by an end user.
-
Replaceable light source by authorized personnel only.
-
Upon and of life on the control gear the whole produce will be replaced.
SAFETY INSTRUCTIONS
-
This fitting is produced and tested in accordance with the strictest European safety standards (EN 60.598-1 ).
-
This fitting cannot be disposed of as household waste. For disposal information ask the local authorities about how to collect it.
-
As indicated by specific regulations, the lighting fitting should be installed by a qualified electrician.
-
If the external wire is damaged it has to be replaced exclusively by the manufacturer, distributor or by a qualified electrician.
-
Always isolate power before commencing installation, maintenance or repair.
-
The luminaire contains certain parts which can be very hot.
-
Each material requires specific mounting accessories. Use screws and wall plugs suitable for the material to which they are fastened. Those included may be unsuitable.
-
Always tighten the screws firmly to avoid contact problems.
-
This fitting should only be installed indoors.
-
Luminaires not suitable for recessed on normally flammable surfaces.
-
Luminaire not suitable for direct mounting on normal flammable surfaces.
-
This fitting is only suitable for fixing to the ceiling.
-
This fitting is only suitable for fixing to the wall.
-
The weight of the lamp has to be supported by the chain. Adjust the length of the electric wire so that it is longer than the chain.
-
Only use lamps which do not exceed the maximum specified wattage.
-
Always observe the minimum distance between the lamp and the surface being lit, as shown in the icon. The lamp can cause a fire if the minimum distance is not observed.
-
Auto-protected bulb. Only use bulbs marked with this symbol. Halogen bulbs get very hot. Wait
until they cool down before replacing. -
Cracked or broken safety glass has to be replaced immediately. Use only manufacturer approved parts complying with regulations.
-
Light source with not-substitutable light emitting diode (LED). Do not disassemble the product since the diodes can damage the eyes. Do not immerse in water. Wipe with a damp cloth. Do not use solvents or strong detergents.
-
This fitting is equipped with a fuse. If the lamp is out of order, replace the internal fuse.
-
Class I Electrical safety guaranteed by the main insulation and an additional protective cond uctor (earthing) connected with the metal frame of the lamp. Earthing is obligatory.
-
Class II Electrical safety guaranteed by the main insulation and a double or reinforced insulation. Earthing not necessary.
-
Class Ill Electrical safety guaranteed by very low power supply (less than 50 Volt). Earthing excluded.
-
Not protected.
-
Protected against solid objects greater than 50 mm.
-
Protected against solid objects greater than 1′ 2 mm.
-
Protected against solid objects greater than 2,5 mm.
-
Protected against solid objects greater than 1 mm.
-
Dust protected.
-
Totally protected against dust infiltration.
-
Not protected.
-
Protected against vertically falling water drops.
-
Protected against water drops falling with a maximum angle of 15° to the vertical axis.
-
Protected against rain.
-
Protected against splashing water.
-
Protected against water jets.
-
Protected against strong water jets.
-
Protected against temporary immersion.
-
Protected against prolonged immersion.
-
Luminaire not suitable for covering with thermally insulating material.
-
Caution, risk of electric shock.
-
Do not stare at the operating light source.
CUSTOMER SUPPORT
IDEAL LUX s.r.l.
Via Taglio Destro 32
30035 Mirano (VE) Italy
www.ideal-lux.com
IDEAL LUX Warehouse
Via delle Industrie, 8/D
30036 Santa Maria di Sala (Venezia)
8.00 – 12.00 / 13.30 – 17.00
