OPT7 LIGHTING AURA PRO Universal Underbody Instruction Manual

June 9, 2024
OPT7 LIGHTING

OPT7 LIGHTING AURA PRO Universal Underbody

COMPONENTS

OPT7 LIGHTING AURA PRO Universal Underbody 1

INSTALLATION

STEP 1
Inspect kit to ensure all contents was included.
STEP 2
Decide where to locate the control box and ensure wiring has enough length for light bars to be installed in desired location.

IMPORTANT
The control box must be installed inside the vehicle as it is not waterproof. Avoid installation areas of the engine bay + heated surfaces.

EXAMPLES
OPT7 LIGHTING AURA PRO Universal Underbody 2

The extension wires are on the led bar. Lay out the bars to measure the length prior to install for a successful installation.

  • 2 x 48” LED Bar + 8ft extension wire
  • 1 x 36” LED Bar + 18ft extension wire
  • 1 x 36” LED Bar + 8ft extension wire

WARNING

  • Connecting to more than 10 AMP will override the kit and cause early failure, ensure it is 10AMPs or less!!
  • Please ensure that the LED bars or strips/control box/wiring all are mounted in areas where will not exceed 85℃ or 185℉.

Once connected, plug the control box Cigarette Power Adapter into an available 12 volt charging port.

OPT7 LIGHTING AURA PRO Universal Underbody 3

or connect the positive wire to the fuse tap and connector the open negative wire to a ground (any metal surface). Then plug the fuse tap into the 10amp switched fuse.

IMPORTANT: Connecting to more then 10amp will override the kit and cause early failure, ensure it is 10amps or less

OPT7 LIGHTING AURA PRO Universal Underbody 4

WARNING: DO NOT directly wire to car battery. Please use the fuse tap we provided. Also ensure that the led bars or strips/control box/wiring all are mounted in areas where will not exceed 85C or 185F.

STEP 3
Scan the QR code on the back of the control box to download the app.

STEP 4
Secure Control box in desired location with Velcro or zipties. The control box is NOT waterproof. Tuck it away from the elements.

STEP 5
Secure the light bars using the zip ties to tie all the wiring away from the moving components.

OPT7 LIGHTING AURA PRO Universal Underbody 5

IMPORTANT: The LED connectors are not waterproof. You will need to use HEAT SHRINK TUBE (not included) or ELECTRICAL TAPE around the LED connectors to ensure the longevity of the lighting kit.

STEP 6
Open the “OPT7 Connect” App, pair your smart phone to the control box, and pick your desired color!

AUX WIRING FOR A DOOR/DOME LIGHT

Please scan to see a detail instruction on Door Assist Sync or go to https://wintis.ladesk.com/549690-AURA-Door-AssistAUX-Installation- Guide

OPT7 CONNECT APP

  • Colors
  • Modes
  • Door Assist
  • Support
  • Ability to control up to
  • 4 devices at once

QR CODE TO DOWNLOAD

OPT7 LIGHTING AURA PRO Universal Underbody 7

DISCLAIMER

OPT7 Lighting is not liable for damages or personal injuries while installing this product. The Installation Guide is intended as assistance to reduce setup time. OPT7 Lighting assumes no responsibility for improper installation. If you are unfamiliar with your vehicle or inexperienced with aftermarket upgrades, please seek professional assistance. OPT7 recommends installation for safety and guidance. Modified installations or installation recommendations not specified by OPT7 Lighting will void product warranty.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

OPT7 LIGHTING User Manuals

Related Manuals