1Mii DS600 Desktop Audio Decoder User Manual
- June 4, 2024
- 1Mii
Table of Contents
1Mii DS600 Desktop Audio Decoder
User Manual
D5600 Desktop Audio Decode
Desktop Audio Decoder
In The Box
Control functions
- Plug in the DC power cable then chooses to connect DS600 with the PC through the USB cable or connect with the CD player through the Coaxial cable.
- The RCA OUT can connect with a headphone amplifier, a power amplifier, and another device.
- Adjust a proper volume, then you can enjoy HiFi music.
Note: For Windows users, the driver needs to be installed when first using. Please refer to “DS600 Driver & Installation Guide” and “DS600- Player Foobar2000 & JR”.
System setting interface
-
Filter mode when playing PCM format, MODE1-MODE7.
MODEL: apodizing fast roll-off filter
MODE2: linear phase fast roll-off filter
MODE3: linear phase slow roll-off filter
MODE4: minimum phase fast roll-off filter
MODE5: minimum phase slow roll-off filter
MODE6: corrected minimum phase fast roll-off filter
MODE7: brick wall filter -
Bluetooth system settings
-
Screen saver settings (Optional screen always on or automatic screen off)
-
Factory data reset(The default values of the system parameters of l-3are: MODE1, Bluetooth on, Automatic screen off.)
-
Note: When entering the system parameter setting interface, it will automatically exit it if there is no operation after 10 seconds
Troubleshooting | Cause Analysis | Solution |
---|---|---|
Noise when COAX / OP input | Signal format error or out of range | Check the |
input signal format
USB does not recognize| Incorrect USB connection| Check or replace the USB
cable
Computer USB port damaged| Change another interface
OS problem| Reinstall the OS
Driver problem| Reinstall driver
No sound when USB input| The computer volume is too low| Adjust volume
Intermittent when USB input| PC is busy and the machine is hung| Waiting for
computer recovery
USB input, pop sound| Software problem| Update motherboard drivers and system
patches
If you still have a problem or question, please contact us
(suppod@lmii.com)
Specifications
USB input | 16bit/44.1kHz-32bitR68kHz DSD64-DSD512(Native) |
---|---|
Optical/ Coaxial input | 16bit/44.1kHz-24bit/192kHz |
Bluetooth input | AAC/SBC/APTX/APTX LL/APTX HD/LDAC |
Power | DCSV/0.5A – 0.25W |
Size | 123.6x110x27.3mm |
Weight | 510g |
Product parameters
Output Voltage | 2.8Vrms@OdBFS |
---|---|
THD+N | <0.0002°/0@1kHz A-weighing |
Noise | <2uVrms@A-weighing |
Crosstalk | -120dB@1kHz |
SNR | 122dB (B-Weighted) |
TND +N
IMD level
Sweep (SMPTE)
Singal to Noise Ratio
Scan the code to get more information.
https://1mii.com/download-2/
©1Mii Technologies Limited.
We hope you never have the need, but if you do, our service is friendly and
hassle-free.
support@lmii.com
web: www.lmii.com
FCC ID: 2AUFR-DS600
MADE IN CHINA
FCC Caution
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Any Changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates uses and
can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
The device has been evaluated to meet general RF exposure requirements. The device can be used in portable exposure conditions without restriction.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>