PERLESMITH PSLTK1-J Listed TV Mount Instruction Manual
- June 14, 2024
- Perlesmith
Table of Contents
Large Tilting TV Wall Mount
Instruction Manual
PSLTK1-J Listed TV Mount
Model: PSLTK1
Thank you for choosing this PERLESMITH product! At PERLESMITH, we strive to
provide you with the best quality products and services in the industry.
Should you have any issues, please don’t hesitate to contact us.
Technical Support:
(US / CA) 1-800-556-6806 Mon-Fri 8am –
8pm (CST)
(UK) 44-808-196-3891 Mon-Fri 2pm – 10pm (UTC)
Other Info:
supportus@perlesmith.com
supportjp@perlesmith.com (JP)
Website:www.perlesmith.com
IMPORTANT SAFETY INFORMATION
Please carefully read all instructions before attempting installation. If you
do not understand the instructions or have any concerns or questions, please
contact our customer service at
supportus@perlesmith.com.
CAUTION: Avoid potential personal injuries and property damage!
- Do not use this product for any purpose that is not explicitly specified in this manual. Do not exceed weight capacity. We are not liable for damage or injury caused by improper mounting, incorrect assembly or inappropriate use.
- This product is designed for use in wood stud, solid concrete, concrete block and brick walls. — DO NOT install into drywall alone.
- The wall must be capable of supporting five times the weight of the TV and mount combined.
Weight Restrictions
If your TV weighs more, this mount is NOT compatible.
WARNING
DO NOT exceed the maximum weight indicated. This mounting system is intended
for use only within the maximum weights indicated. Use with products heavier
than the maximum weights indicated may result in failure of the mount and its
accessories, causing damage and or injury.
Check the VESA Pattern of TV before the Installation
100mm ≈ 3.9”
200mm ≈ 7.9”
400mm ≈ 15.7”
600mm ≈ 23.6”
Minium VESA pattern:200mm/7.9”(W)x 100mm/3.9”(H)
If your TV VESA is greater than 600 x 400mm / 23.6 x 15.7” or less than VESA
200 x 100mm / 7.9 x 3.9”, this mount is NOT compatible.
If this mount is NOT compatible, please contact customer service at
supportus@perlesmith.com to find a
compatible mount.
Verify Your Wall Construction
CAUTION
DO NOT install into drywall alone
I you are not sure of the wall construction, please contact our customer service at supportus@perlesmith.com.
Tools Needed (Not Included)
(Tools Needed for Wood Stud Installation)
(Tools Needed for Solid Concrete, Concrete Block and Brick Wall Installation)
Supplied Parts and Hardware
WARNING: This product contains small items that could be a choking hazard
if swallowed.
Before starting assembly, verify all parts are included and undamaged. Do not
use damaged or defective parts. If you require replacement parts, please
contact our customer service at
supportus@perlesmith.com.
- PLEASE NOTE: Not all hardware included in this package will be used.
Supplied Parts and Hardware for Step 1
Supplied Parts and Hardware for Step 2 and 3
Step 1 Secure the TV Brackets to the TV
BOLT LENGTH: Verify adequate thread engagement with bolts or bolts /spacers combination. We recommend thread engagement by at least 5 turns.
- Too short will not hold the TV.
- Too long will damage the TV.
PLEASE NOTE: The provided TV bolts meet most of today’s TVs design.
However, some TVs require special bolts which may NOT be in the hardware bag.
In this case, we offer our “PSUHP” Universal Hardware Kit which provides a
large selection of bolts that can meet the demand of older and unique
applications.
IMPORTANT: When using the spacers, it is important to note that they can
be used in multi-layers (meaning stacked). If you have any difficulty
undestanding how to install the TV bolts or spacers, please contact customer
service at supportus@perlesmith.com.
CAUTION: When attaching the TV brackets [03] and [04] to the back of the
TV, ensure the ends with round holes on the TV brackets are pointing to the
top of the TV and are equally centered on the back of the TV.
PLEASE NOTE: The bolt hole locations on your TV may vary in accordance of
the manufacturer’s design of the TV. We are only illustrating possible
locations of the bolt holes.
Option A (For Flat Back TV)
Option B (For Round Back TV)
Option C (For TV with A “Bump”)
Option D
For cable interference or inset holes, use spacers [06] to create extra space
between the TV and TV brackets.
Step 2 Assemble the Wall Plate
2-1 Loosen 4 preassembled bolts [S1] using Phillips screwdriver and keep
for the use in 2-2.
2-2 Secure the right wall plate [01] to the left wall plate [02] by tightening
the bolts [S1].
Step 3 Attach the Wall Plate to
For wood stud installation, follow STEP 3A.
For concrete installation, follow STEP 3B.
Step 3A Wood Stud Option
WARNING:
- Avoid potential personal injury or property damage! Do not use a drill for tightening the lag screws! Only use a socket wrench. DO NOT over-tighten the lag screws [A1]. Tighten the lag screws [A1] only until they are pulled firmly against the wall plate [01] and [02].
- DO NOT USE THE ANCHOR [A2] FOR THIS STEP!
- Ensure the wall plate [01] and [02] is securely fastened to the wall before continuing to the next step.
- Any material covering the wall must not exceed 5/8” (16mm).
- Nominal wood stud size: common 2 x 4” (51 x 102mm) minimum 1 1/2 x 3 1/2” (38 x 89mm).
- Stud center must be verified.
Use a stud finder (NOT included) to locate wood studs or use an awl (NOT included) to verify the edges. Mark the edge and center locations.
Position the wall plate [01] and [02] at your desired height and line up the holes with your stud center line. Level the wall plate [01] and [02] and mark the holes.
Drill 4 pilot holes using a 7/32” (6.6mm) diameter drill bit. Make sure the depth is NOT less than 2 3/4” (70mm).
Install the wall plate [01] and [02] using lag screws [A1]. Tighten the lag screws [A1] only until they are pulled firmly against the wall plate [01] and [02]. Do not over-tighten the lag screws [A1].
Step 3B Solid Concrete or Concrete Block Option
WARNING:
- Avoid potential personal injury or property damage! Do not use a drill for tightening the lag screws! Only use a socket wrench. DO NOT over-tighten the lag screws [A1]. Tighten the lag screws [A1] only until they are pulled firmly against the wall plate [01] and [02].
- Ensure the wall plate [01] and [02] is securely fastened to the wall before continuing to the next step.
- Mount the wall plate [01] and [02] directly onto the concrete surface.
- Anything covering the wall must not exceed 5/8” (16mm).
- Minimum solid concrete thickness: 8” (203mm).
- Minimum concrete block size: 8 x 8 x 16” (203 x 203 x 406mm).
- NEVER drill into the mortar between blocks.
Position the wall plate [01] and [02] at your desired height, level the wall plate [01] and [02] and mark the pilot hole locations.
Drill 4 pilot holes using a 3/8” (10mm) diameter drill bit. Make sure the depth is NOT less than 3” (75mm). NEVER drill into the mortar between the blocks.
Use the hammer to knock anchors [A2] into the wall. Be sure the anchors [A2] are seated flush with the concrete surface.
Install wall plate [01] and [02] using lag screws [A1]. Tighten the lag screws [A1] only until they are pulled firmly against the wall plate 01] and [02]. Do not over-tighten the lag screws [A1].
Step 4
Verify Wall Mount Installation by Putting Pressure on Wall Mount
Before attaching the TV to the mount, please try to pull down the TV wall
mount with your hands to check whether it is firmly secured.
Step 5 Adjust Tilt Angle of TV
Slightly loosen 4 preassembled tilt tension bolts [S] in brackets [03] and
[04]. Adjust the hooks [H] to your desired angle. Then tighten tilt tension
bolts with a Phillips screwdriver (not included) to fix the tilting angle of
the TV.
Step 6 Secure the TV onto the Wall Plate [01] and [02]
- Hang the TV with brackets [03] and [04] onto the wall plate [01] and [02].
- While pulling and holding both ropes [R], press the bottom of the TV into the wall plate [01] and [02] until the latches lock the wall plate [01] and [02], then release the ropes [R].
HEAVY! You may need assistance with this step.
Step 7 Remove the TV
-
Disconnect all cables, pull down and hold both ropes [R] while gently pulling the bottom of the TV away from the wall.
CAUTION: Avoid potential personal injury or property damage! To prevent breaking the locking latches, always pull and hold the ropes [R] down while pulling the TV away from the wall. -
Then lift the TV up and remove from the wall plate [01] and [02].
HEAVY! You may need assistance with this step.
860-00285-07 Rev00
Documents / Resources
|
PERLESMITH PSLTK1-J Listed TV
Mount
[pdf] Instruction Manual
PSLTK1-J Listed TV Mount, PSLTK1-J, Listed TV Mount, TV Mount, Mount
---|---
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>