PERLESMITH PSTM2 TV Tripod Stand Instruction Manual

TV Tripod Stand
Instruction Manual V2.0

Model:PSTM2

Thank you for choosing this product! We strive to provide you with the best quality products and services in the industry. Should you have any issues, please don’t hesitate to contact us at Technical Support:
(US/CA)1-800-556-6806 Mon-Fri 8am – 8pm(CST) Other Info: service.popopopo@gmail.com

Improtant Safety Instructions

• Check to assure that all components were received undamaged. Do not use damaged or defective parts. lf you require replacement parts, contact customer service at service.popopopo@gmail.com.

• Install and operate this product with care. Please read this instruction before beginning the installation, and carefully follow all instructions contained herein. Use proper tools during installation.

• If you do not understand the instructions or have any concerns or questions, please contact customer service at service.popopopo@gmail.com

• Do not use this product for any purpose that is not explicitly specified in this manual. Do not exceed weight capacity. We cannot be liable for damage or injury caused by improper mounting, incorrect assembly or inappropriate use.
  TIP OVER WARNING
  SERIOUS OR FATAL CRUSHING INJURIES CAN OCCUR FROM TIP OVER.
  TO HELP PREVENT TIP OVER:

• NEVER ALLOW CHILDREN TO CLIMB, STAND, HANG, OR PLAY ON ANY PART OF TV OR TV STAND.

• USE TIP OVER RESTRAINT OR ANCHOR STAND TO WALL USE OF TIP OVER RESTRAINTS MAY ONLY REDUCE, BUT NOT ELIMINATE RISK OF TIP OVER.

Check the VESA Pattern of TV before the Installation

100mm ≈ 4 in
200mm ≈ 7 7/8 in
300mm ≈ 11 3/4 in
400mm ≈ 15 3/4 in
600mm ≈ 23 6/10 in
Minimum VESA pattern: 200mm/8 in(W)x100mm/4 in(H)
If your TV VESA is greater than 600×400 mm/24×16 in or less than VESA 100x100mm/4×4 in, this TV tripod stand is NOT compatible.
If this TV tripod stand is NOT compatible, please contact customer service at service.popopopo@gmail.com to find a compatible product.

STEP 1 Adjust the Height of Pole

Weming :
; After adjusting the pole to , desired height, insert the latch 1 1 [S] to the holes on the upper ‘ pole. Fasten the knob [K1]to —, , hold upper pole. my
CAUTION:  DISTANCE BETWEEN EACH FOOT MUST BE 600mm/23.6in

1. Loosen the lower knob.
2. Adjust the distance between each feet to be 600mm/23.6in
3. Tighten the lower knob
   CAUTION: TO AVOID ANY INJURIES, PLEASE TAKE OFF TV SET BEFORE MAKING HEIGHT ADJUSTMENT

STEP 2 Secure the Head Assembly with TV Plate to Pole Assembly

STEP 3 Secure the TV Brackets to Your TV

First, make sure the diameter of the bolt(A—E) fits your TV. Then, please see the diag- ram above. You will need to thread the bolts into the TV using the correct washers(F)
and spacers (G or H) if necessary with a screwdriver(Not included). Please make sure the TV brackets(K) are vertically centered and level with each other.
STEP 4 Secure the TV onto the Plate

STEP 5 Adjust Level and Tilt Angles
Warning: Do not over-loosen the nuts or bolts to prevent the TV from falling down.

STEP 6 Manage the Cables

Documents / Resources

| PERLESMITH PSTM2 TV Tripod Stand [pdf] Instruction Manual
PSTM2 TV Tripod Stand, PSTM2, TV Tripod Stand, Tripod Stand, Stand
---|---

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>