PERLESMITH TV Wall Mount PSMFK13 Instruction Manual

June 6, 2024
Perlesmith

TV Wall Mount PSMFK13

TV Wall Mount Instruction Manual
V1.0

Model:PSMFK13

Thank you for choosing this Perlesmith product! At Perlesmith we strive to provide you with the best quality products and services in the industry. Please share your experience of our product with others at www.perlesmith.com/pages/reviews if you are satisfied. Should you have any issues, please don’t hesitate to contact us.

Website: www.perlesmith.com

Technical Support: 1-800-556-6806 Mon- Fri 10am – 5pm (PST) (USA) (CAN) Other Info: supportus@perlesmith.com (US/CA/DE/UK/FR/IT/ES/AU)

IMPORTANT SAFETY INFORMATION
Please carefully read all instructions before attempting installation. If you do not understand the instructions or have any concerns or questions, please contact our Technical Support line at 1-800-556-6806 or customer service at supportus@perlesmith.com CAUTION: Avoid potential personal injuries and property damage! · Do not use this product for any purpose that is not explicitly specified in this manual. Do not exceed weight capacity. We are not liable for damage or injury caused by improper mounting, incorrect assembly or inappropriate use. · This product is designed for use in wood stud, solid concrete, and concrete block walls · DO NOT install into drywall alone. · The wall must be capable of supporting five times the weight of the TV and mount combined.
Check the VESA Pattern of Your TV before the Installation

MAX:400mm/16 in.

MAX:400mm/16 in.

75 mm 3 in. 100 mm 4 in. 200 mm 7 7/8 in. 300 mm 11 3/4 in. 400 mm 15 3/4 in.

Minimum VESA pattern: 75mm/3 in.(W)x75mm/3 in.(H)
If your TV VESA is greater than 400×400 mm/16×16 in. or less than VESA 75x75mm/3x3in., this mount is NOT compatible.
If this mount is NOT compatible, please contact customer service at supportus@perlesmith.com to find a compatible mount.
Verify Your Wall Construction

CAUTION
DO NOT install into drywall alone

Wood Studs (with Drywall)

Solid Concrete or Concrete Block

If you are are not sure the wall construction, please contact our product
support line at 1-800-556-6806 or customer service at
supportus@perlesmith.com

Tools Needed (Not lncluded)

Stud Finder

Tape Measure

Pencil

Drill

Hammer

5/32 in.(4 mm) Wood Drill

3/8 in.(10mm) Concrete Drill

1/2in.(13mm) Socket Wrench

Screwdriver

Awl

Supplied Parts and Hardware
Warning:This product contains small items that could be a choking hazard if swallowed. Before starting assembly, verify all parts are included and undamaged. Do not use damaged or defective parts. lf you require replacement parts, contact our Product Support line at 1-800-556-6806 or customer service at supportus@perlesmith.com · Please note: Not all hardware included in this package will be used.
Supplied Parts and Hardware for Step 1

Arm Assembly/Wall Plate

01

x1

TV Bracket

02

x4

3/8 in.(10mm) Wrench

F1

Bolt M6 x 20mm x4

F2

Bolt M6 x 12mm x4

F3

Spacer x4

F4

Nut M6 x8

Supplied Parts and Hardware for Step 2

04 Washer

05 Spacers [if needed]

Note: The spacers are shown in accordance with the actual size

M6 [B] x4

L2.5mm [C1] x8

L10mm [C2] x4

06 TV Bolts [Only one bolt size fits your TV] Note: The bolts are shown in accordance with the actual size

M6

L20mm [C3] x4

M6 x 15mm [D1] x4

M8

M6 x 35mm [D2] x4

M8 x 25mm [E1] x4

M8 x 35mm [E2] x4

Supplied Parts and Hardware for Step 3

M8 x 50mm [E3] x4

Note: The lag screw is shown in accordance with the actual size

A1 x4 Lag Screw M7x70mm [G]

CAUTION!

A2 x4

Wall Anchor

These anchors are for concrete or brick walls ONLY. DO NOT use them in drywall or wood studs.

Step 1 Secure the TV Plate to TV Bracket Assembly
Loosen the preassembled bolt [S] to detach the TV plate [a] from the arm assembly/wall plate [01], and keep the preassembled bolt [S] for the use in step 5

a

S

Choose the Combination that Applies to Your VESA Hole Pattern

Option A

4 in.(100mm)

3 in. (75mm)

3 in. (75mm)x3 in. (75mm) 4 in.(100mm)x4 in.(100mm)

4 in.(100mm) 3 in. (75mm)

Option B

15 3/4 in.(400mm) 11 3/4 in.(300mm) 7 7/8 in.(200mm)

8 in. (200mm)x8 in. (200mm) 12 in.(300mm)x12 in.(300mm) 16 in.(400mm)x16 in.(400mm)

15 3/4 in.(400mm) 11 3/4 in.(300mm) 7 7/8 in.(200mm)

Secure the TV brackets [02] to the TV plate [a] using bolts [F2] and nuts [F4].

Adjust the width of the two vertical brackets according to the width of the VESA pattern holes.Then secure the other two brackets [02] to
the two horizontal brackets [02]with TV plate [a] using bolts [F1], spacers [F3] and nuts [F4].

01

F2 02

02

F4

F1

F3

F4

Step 2 Secure the TV Plate or TV Plate with Brackets Assembly to TV
Select TV Bolts
Only one bolt size fits your TV. M6 M8

Bolt length: Verify adequate thread engagement with bolts or bolts/spacers combination. We recommend thread engagement by at least 5 turns. -Too short will not hold the TV. -Too long will damage the TV.

Too Short

Too Long

Correct

Correct

Note: If necessary, the spacers can be used in multi-layer. If the installation fails after trying various methods, please contact customer service at supportus@perlesmith.com

CAUTION: Ensure the TV plate assembly are EQUALLY CENTERED on your TV and securely fastened in place.
UP
Option A (For Flat Back TV)

06 D1/E1 04 B
05 C1/C2 If Needed

Alternate Spacer Setups

Option B (For Round Back TV)

06 D2/E2/E3 04 B
05 C1/C2/C3

Alternate Spacer Setups

Option C (For TV with A “Bump”) Spacers may be necessary for 2 holes ONLY.

06 D2/E2/E3 04 B
05 C1/C2/C3
Alternate Spacer Setups

D1/E1 06 B 04
C1/C2 05 If Needed

Option D For cable interference or inset holes, use spacers [05] to create extra space between the TV and TV plate assembly
05 C1/C2/C3 06 D2/E2/E3
04 B
Alternate Spacer Setups

Step 3 Attach the Arm Assembly/Wall Plate [01] to Wall

For wood stud installation, follow STEP 3A For concrete installation, follow STEP 3B
Step 3A Wood Stud Option

WARNING:
Avoid potential personal injury or property damage! DO NOT over-tighten the lag screws [A1]. Tighten the lag screws [A1] only until they are pulled firmly against the wall plate.

DONOT USE ANCHOR [A2] FOR THIS STEP!
Ensure the arm assembly/wall plate [01] is securely fastened to the wall before continuing to the next step.

X

Any material covering the wall must not exceed 5/8 in. (16 mm) Nominal wood stud size: common 2 x 4 in. (51 x 102 mm) minimum 1½ x 3½ in. (38 x 89 mm) Stud center must be verified

3A-1

CAUTION!
If the stud is not quite well where you’d like, please refer to the step 3A-3 in Page 09 (Horizontal Shift) to adjust the position

3A-2

16 in.(406mm)

Use a stud finder(not included) to locate wood studs or use an awl (not included) to verify the edges. Mark the edge and center locations.

Awl (Not lncluded)

Position the arm assembly/wall plate [01] at your desired height and line up the holes with your stud center line. Level the arm assembly/wall plate [01] and mark the holes.

HEAVY! You may need assistance with this step.

3A-3 Shift the Arm AssemblyIf Needed

To better position your mount and TV on your wall,the mount can be horizontal shifted

side to side by following these steps

3A-3-1

Lossen the four preassembled bolts using wrench, and keep the four bolts for use in the step 3A-3-3

3A-3-2 Shift the arm assembly to your desired position.

3/8 in.(10mm)
Wrench

3A-3-3 Fasten the four bolts using wrench to fix the arm assembly to your desired
position.
3/8 in.(10mm)
Wrench

3A-4 3A-5

Drill 4 pilot holes using a 5/32 in.(4 mm) mm diameter drill bit. Make sure the depth is not less than 2 3/4 in.(70mm)
2 3/4 in.(70mm)
ø5/32 in.(4 mm)
Install the wall plate using 4 lag screws [A1]. Tighten the lag screws [A1] only until they are pulled firmly against the wall plate.

HEAVY! You may

need assistance with

A1

this step.

Step 3B Solid Concrete or Concrete Block Option

1/2 in.(13mm) Socket Wrench (Not included)

WARNING:
Avoid potential personal injury or property damage! DO NOT over-tighten the lag screws [A1]. Tighten the lag screws [A1] only until they are pulled firmly against the wall plate.

Ensure the wall plate [01] is securely fastened to the wall before continuing to the next step.
Any material covering the wall must not exceed 5/8 in. (16 mm) Mount the wall plate directly onto the concrete surface Minimum solid concrete thickness: 203 mm (8 in.) Minimum concrete block size: 203 x 203 x 406 mm (8 x 8 x 16 in.) Never drill into the mortar between blocks

Wall Anchor
A2

3B-1
3B-2
3B-3 A2
3B-4

Position arm assembly/wall plate

01

[01] at your desired height, level the wall arm assembly/wall plate [01] and mark the pilot hole

locations.

Drill 4 pilot holes using a 3/8 in.(10mm)diameter drill bit. Make sure the depth is not less than 3 in.(75mm). Never drill into the mortar between blocks.
3 in.(75mm)
ø3/8 in.(10mm)
Use the hammer to knock anchors [A2] into the wall. Be sure the anchors [A2] are seated flush with the concrete surface.

Install wall plate using lag

screws [A1] and anchors [A2].

Tighten the lag screws [A1] only

until they are pulled firmly

against the wall plate. DO NOT

01

over-tighten the lag screws [A1].

You may need

1/2 in.(13mm)

A1

assistance with this step.

Socket Wrench (Not included)

Step 4 Secure the TV onto the Arm Assembly/Wall Plate
Secure the TV with TV bracket assembly and TV plate onto the arm assembly/wall plate by tightening the bolts [S]using wrench

S
Step 5 Level Adjustment

3/8 in.(10mm)
Wrench
HEAVY! You may need assistance with this step.

S

1. Loosen the bolt [S]. 2. Level the TV 3. Tighten the bolt [S] to secure TV in place.

or
Screwdriver (Not included)

3/8 in.(10mm)
Wrench

Step 6 Tilt Adjustment

T

T

Loosen

Tighten

1. Loosen the preassembled bolts [T] using wrench. 2. Adjust TV to your desired tilt angle. 3. Tighten the preassembled bolts [T] to secure TV in place

3/8 in.(10mm)
Wrench

Thank you again
for choosing this Perlesmith product!
All of us at Perlesmith do appreciate your product purchase. We hope that you are as happy with your product as we are designing and manufacturing it for you. We strive to provide you with the best quality products and services in the industry. Please share your experience of our product with others at www.perlesmith.com if you are satisfied. If you have any questions please don’t hesitate to contact us at Technical Support: 1-800-556-6806 Mon-Fri 10am – 5pm (PST) (USA) (CAN) Other Info: supportus@perlesmith.com (US/CA/DE/UK/FR/IT/ES/AU) Please check www.perlesmith.com for more products and company information.

Perlesmith offers products in these categories

TV Stands

Anti-tip Straps

AV Shelves

Speaker Stands

TV Carts

Full Motion Mounts

Tilt Mounts

Corner Mounts

Please remember us when you need one.

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals