PERLESMITH TV Wall Mount PSLF6 Instruction Manual
- June 6, 2024
- Perlesmith
Table of Contents
TV Wall Mount
Instruction Manual
Model:PSLF6
V2.0
Thank you for choosing this Perlesmith product! At Perlesmith we strive to
provide you with the best quality products and services in the industry.
Please share your experience of our product with others at
www.perlesmith.com/pages/reviews if
you are satisfied. Should you have any issues, please don’t hesitate to
contact us.
Website: www.perlesmith.com
Technical Support:
1-800-556-6806 Mon-Fri 10am – 5pm (PST)
(USA) (CAN)
Other Info:
supportus@perlesmith.com (US)
supportca@perlesmith.com (CA)
IMPORTANT SAFETY INFORMATION
Please carefully read all instructions before attempting installation. If you
do not understand the instructions or have any concerns or questions, please
contact our Technical Support line at
1-800-556-6806 or customer service at
supportus@perlesmith.com
(US)/supportca@perlesmith.com (CA)
CAUTION: Avoid potential personal injuries and property damage!
- Do not use this product for any purpose that is not explicitly specified in this manual. Do not exceed weight capacity. We are not liable for damage or injury caused by improper mounting, incorrect assembly, or inappropriate use.
- This product is designed for use in wood stud, solid concrete, concrete block brick walls – DO NOT install into drywall alone.
- The wall must be capable of supporting five times the weight of the TV and mount combined.
Weight Restrictions
If your TV weighs more, this mount is NOT compatible.
WARNING
DO NOT exceed the maximum weight indicated. This mounting system is intended
for use only within the maximum weights indicated. Use with products heavier
than the maximum weights indicated may result in failure of the mount and its
accessories, causing possible damage and or injury.
Check the VESA Pattern of Your TV before the Installation
Minimum VESA pattern: 200mm/8 in.(W)x100mm/4 in.(H)
100 mm ≈ 4 in.
200 mm ≈ 7 7/8 in.
400 mm ≈ 15 3/4 in.
300 mm ≈ 11 3/4 in.
600 mm ≈ 23 6/10 in.
If your TV VESA is greater than 600×400 mm/24×16 in. or less than VESA 200x100mm/8x4in., this mount is NOT compatible.
Verify Your Wall Construction
CAUTION
DO NOT install into drywall alone
If you are not sure about the wall construction, please contact our product
support line at 1-800-556-6806 or
customer service at
supportus@perlesmith.com (US)
supportca@perlesmith.com (CA)
Tools Needed (Not included)
Supplied Parts and Hardware
Warning: This product contains small items that could be a choking hazard
if swallowed.
Before starting assembly, verify all parts are included and undamaged. Do not
use damaged or defective parts. if you require replacement parts, contact our
Product Support line at 1-800-556-6806
or customer service at
supportus@perlesmith.com
(US)/supportca@perlesmith.com (CA)
- Please note: Not all hardware included in this package will be used.
Supplied Parts and Hardware for Step 1
The TV brackets are attached to the arm assembly/ wall plate with plastic
cable ties
TV
Bracket
03 x2
|
---|---
07 TV Bolts [Only one bolt size fits your TV] Note: The bolts are
shown in accordance with the actual size
Supplied Parts and Hardware for Step 2
Note: The lag screw is shown in accordance with the actual size
Supplied Parts and Hardware for Step 3 to Step 6
Step 1 Secure the TV Brackets to TV
Bolt length: Verify adequate thread engagement with bolts or bolts/spacers
combination.
We recommend thread engagement by at least 5 turns.
-Too short will not hold the TV.
-Too long will damage the TV.
Note: If necessary, the spacers can be used in multi-layer. If the
installation fails after trying various methods, please contact customer
service at
supportus@perlesmith.com
(US)/supportca@perlesmith.com (CA)
CAUTION: Ensure the TV brackets [03] are EQUALLY CENTERED on your TV AND
securely fastened in place.
Option C (For TV with A “Bump”) Spacers may be necessary for 2 holes
ONLY.
Option D
For cable interference or inset holes, use spacers [06] to create extra space
between the TV and TV brackets
Step 2 Attach the Wall Plate [01] to Wall
For wood stud installation, follow STEP 2A
For concrete installation, follow STEP 2B
Step 2A Wood Stud Option
WARNING:
- Avoid potential personal injury or property damage! DO NOT over-tighten the lag screws [A1]. Tighten the lag screws [A1] only until the washers [A2] is pulled firmly against the wall plate.
- DONOT USE ANCHOR [A3] FOR THIS STEP!
- Ensure the wall plate [01] is securely fastened to the wall before continuing to the next step.
- Any material covering the wall must not exceed 5/8 in. (16 mm)
- Nominal wood stud size: common 2 x 4 in. (51 x 102 mm) minimum 1½ x 3½ in. (38 x 89 mm)
- Stud center must be verified
Position the wall plate template [04] at your desired height and line up the
holes with your stud centerline. Level the wall plate template [04] and mark
the holes.
Drill 4 pilot holes using a 7/32 in.(5.5 mm) diameter drill bit. Make sure the
depth is not less than 2 9/16 in.(65mm).
Install the wall plate using lag screws [A1] and washer [A2]. Tighten the lag
screws [A1] only until the washers [A2] are pulled firmly against the wall
plate.
You may need assistance with this step.
Step 2B Solid Concrete or Concrete Block Option
WARNING:
- Avoid potential personal injury or property damage! DO NOT over-tighten the lag screws [A1]. Tighten the lag screws [A1] only until the washers [A2] are pulled firmly against the wall plate.
- Ensure the wall plate [01] is securely fastened to the wall before continuing to the next step.
- Any material covering the wall must not exceed 5/8 in. (16 mm)
- Mount the wall plate directly onto the concrete surface
- Minimum solid concrete thickness: 203 mm (8 in.)
- Minimum concrete block size: 203 x 203 x 406 mm (8 x 8 x 16 in.)
- Never drill into the mortar between blocks
Position the wall plate template [04] at your desired height, level the wall
plate template, and mark the pilot hole locations.
Drill 6 pilot holes using a 3/8 in.(10mm)diameter drill bit. Make sure the
depth is not less than 2 3/4 in.(70mm). Never drill into the mortar between
blocks.
|
---|---
Use the hammer to knock anchors [A3] into the wall. Be sure the anchors [A3]
are seated flush with the concrete surface.
Install wall plate using lag screws [A1], washers [A2], and anchors [A3].
Tighten the lag screws [A1] only until the washers [A2] is pulled firmly
against the wall plate. DO NOT over-tighten the lag screws [A1].
You may need assistance with this step.
Step 3 Secure the Arm Assembly [02] to Wall Plate [01]
- Hang the arm assembly [02] to the wall plate [01].
- Shift the arm assembly [02] along with the wall plate [01] to your desired position.
- Secure the arm assembly [02] to the wall plate [01] using bolts [F1].
Note: The bolts [F1] need to be tightened hard.
Step 4 Secure Front Support to Arm Assembly
- Make sure the big button in Front Support [08] hangs on the hook of the arm assembly.
- Secure the front support [08] to arm assembly [02] using bolts [F2].
Step 5 Hang the TV onto the Front Support
Press the safety locks down, then fasten the removed bolts [S]
HEAVY! You may need assistance with this step.
Step 6 Adjustments
|
- Loosen the preassembled knob [T].
- Adjust TV to your desired tilt angle.
- Tighten the preassembled knob [T] to secure the TV in place.
---|---
CAUTION!
DO NOT
over-loosen these four nuts when adjusting the level angle to prevent the TV
from falling off.
-
Loosen the bolt [F2] .
-
Level your TV.
-
Tighten the bolt [F2] to secure the TV in place.
Note: Please take off the TV before shifting the arm assembly along the wall plate
To better position your mount and TV on your wall, the mount can be horizontal shifted left to right by following these steps.
- Loosen the bolts [F1].
- Shift the arm assembly [02] to your desired position.
- Tighten the bolts [F1] hard.
- Repeat the procedures in Step 5 to rehang and secure the TV onto the front support[08].
Note: The bolts [F1] need to be tightened hard.
HEAVY! You may need assistance with this step.
Thank you again for choosing this Perlesmith product!
All of us at Perlesmith do appreciate your product purchase. We hope that you are as happy with your product as we designing and manufacturing it for you. We strive to provide you with the best quality products and services in the industry. Please share your experience of our product with others at www.perlesmith.com/pages/reviews if you are satisfied. If you have any questions please don’t hesitate to contact us at
Technical Support:
1-800-556-6806 Mon-Fri 10am – 5pm
(PST) (USA) (CAN)
Other Info :
supportus@perlesmith.com (US）
supportca@perlesmith.com (CA)
Please check
www.perlesmith.com
for more products and
company information.
Perlesmith offers products in these categories please remember us when you
need one. Please remember us when you need one.
Please remember us when you need one.
Documents / Resources
|
PERLESMITH TV Wall Mount
PSLF6
[pdf] Instruction Manual
PERLESMITH, PSLF6, TV, Wall Mount
---|---
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>