PERLESMITH TV Wall Mount PSXF3 Instruction Manual
- June 6, 2024
- Perlesmith
Table of Contents
TV Wall Mount PSXF3
TV Wall Mount Instruction Manual
V1.0
Model:PSXF3
Thank you for choosing this Perlesmith product! At Perlesmith we strive to provide you with the best quality products and services in the industry. Please share your experience of our product with others at www.perlesmith.com/pages/reviews if you are satisfied. Should you have any issues, please don’t hesitate to contact us.
Website: www.perlesmith.com
Technical Support: 1-800-556-6806 Mon- Fri 10am – 5pm (PST) (USA) (CAN) Other Info: supportus@perlesmith.com (US/CA/DE/UK/FR/IT/ES/AU)
IMPORTANT SAFETY INFORMATION
Please carefully read all instructions before attempting installation. If you
do not understand the instructions or have any concerns or questions, please
contact our Technical Support line at
1-800-556-6806 or customer service at
supportus@perlesmith.com CAUTION: Avoid potential personal injuries and
property damage! · Do not use this product for any purpose that is not
explicitly specified in this manual. Do not exceed weight capacity. We are not
liable for damage or injury caused by improper mounting, incorrect assembly or
inappropriate use. · This product is designed for use in wood stud, solid
concrete, and concrete block walls – DO NOT install into drywall alone. · The
wall must be capable of supporting five times the weight of the TV and mount
combined.
Weight Restrictions
132 lbs. (60 kg)
If your TV weighs more, this mount is NOT compatible.
WARNING
DO NOT exceed the maximum weight indicated. This mounting system is intended
for use only with the maximum weights indicated. Use with products heavier
than the maximum weights indicated may result in failure of the mount and its
accessories, causing possible damage and or injury.
Check the VESA Pattern of Your TV before the Installation
MAX:400mm/16 in.
MAX:800mm/31 in.
100 mm 4 in. 200 mm 7 7/8 in. 300 mm 11 3/4 in. 400 mm 15 3/4 in. 600 mm 23 6/10 in. 800 mm 31 1/2 in.
Minimum VESA pattern: 200mm/8 in.(W)x100mm/4 in.(H)
If your TV VESA is greater than 800×400 mm/31×16 in. or less than VESA
200x100mm/8x4in., this mount is NOT compatible. If this mount is NOT
compatible, please contact customer service at supportus@perlesmith.com to
find a compatible mount.
01
Verify Your Wall Construction
CAUTION
DO NOT install into drywall alone
Wood Studs (with Drywall)
Solid Concrete or Concrete Block
Tools Needed (Not lncluded)
If you are not sure the wall construction, please contact our product
support line at 1-800-556-6806 or
customer service at
supportus@perlesmith.com
Stud Finder
Tape Measure
Pencil
Drill Hammer
7/32 in.(5.5 mm) Wood Drill
3/8 in.(10mm) Concrete Drill
1/2 in.(13mm) Socket Wrench
Screwdriver
Awl
Supplied Parts and Hardware
Warning:This product contains small items that could be a choking hazard if
swallowed. Before starting assembly, verify all parts are included and
undamaged. Do not use damaged or defective parts. lf you require replacement
parts, contact our Product Support line at
1-800-556-6806 or customer service at
supportus@perlesmith.com · Please note: Not all hardware included in this
package will be used.
Supplied Parts and Hardware for Step 1
The TV brackets are attached to the arm assembly/ wall plate with plastic cable ties
TV Bracket 03 x2
05 Washer
06 Spacers [if needed]
M6/M8 [B] x4
L2.5mm [C1] x8
02
L10mm [C2] x4
L22mm [C3] x4
07 TV Bolts [Only one bolt size fits your TV] Note: The bolts are shown in
accordance with the actual size
M6
M6 x 15mm [D1] x4
M6 x 35mm [D2] x4
M8
M8 x 15mm [E1] x4
M8 x 25mm [E2] x4
M8 x 35mm [E3] x4
Supplied Parts and Hardware for Step 2
M8 x 50mm [E4] x4
Wall Plate
01 x1
Wall Plate Template
04 x1
Level x1
Note: The lag screw is shown in accordance with the actual size
A1
x6
Lag Screw M8x65mm
03
A2 x6
Washer M8
A3 x6
Wall Anchor
CAUTION!
These anchors are for concrete or brick walls ONLY. DO NOT use them in drywall
or wood studs.
Supplied Parts and Hardware for Step 3 to Step 6
Front Support
09 x1
Arm Assembly
02 x1
Bolt [F1] x2
Bolt [F2] x1
Step 1 Secure the TV Brackets to TV
Select TV Bolts
Only one bolt size fits your TV.
M6
M8
Allen Key x1
Bolt length: Verify adequate thread engagement with bolts or bolts/spacers combination. We recommend thread engagement by at least 5 turns. -Too short will not hold the TV. -Too long will damage the TV.
Too Short
Too Long
Correct
Correct
04
Note: If necessary, the spacers can be used in multi-layer. If the
installation fails after trying various methods, please contact customer
service at supportus@perlesmith.com
CAUTION: Ensure the TV brackets [03] are EQUALLY CENTERED on your TV AND
securely fastened in place. 03
UP
Option A (For Flat Back TV)
07 D1/E1 05 B
Option B (For Round Back TV)
07 D2/E2/E3/E4 05 B
06 C1/C2/C3
Alternate Spacer Setups
05
Option C (For TV with A “Bump”) Spacers may be necessary for 2 holes ONLY.
07 D2/E2/E3/E4 05 B
06 C1/C2/C3 Alternate Spacer Setups
D1/E1 07 B 05
Option D For cable interference or inset holes, use spacers [06] to create
extra space between the TV and TV brackets
06 C1/C2/C3 07 D2/E2/E3/E4
05 B
Alternate Spacer Setups 06
Step 2 Attach the Wall Plate [01] to Wall
For wood stud installation, follow STEP 2A For concrete installation, follow
STEP 2B
Step 2A Wood Stud Option
WARNING:
Avoid potential personal injury or property damage! DO NOT over-tighten the
lag screws [A1]. Tighten the lag screws [A1] only until the washers [A2] are
pulled firmly against the wall plate.
DONOT USE ANCHOR [A3] FOR THIS STEP!
Ensure the wall plate [01] is securely fastened to the wall before continuing
to the next step.
X
Any material covering the wall must not exceed 5/8 in. (16 mm) Nominal wood stud size: common 2 x 4 in. (51 x 102 mm) minimum 1½ x 3½ in. (38 x 89 mm) Stud center must be verified
2A-1
Use a stud finder(not included) to
locate wood studs or use an awl (not included) to verify the edges. Mark
the edge and center locations.
2A-2
1264inin.(.4(60069mmmm) )
Awl (Not lncluded)
Position the wall plate template [04] at your desired height and line up the
holes with your stud center line. Level the wall plate template [04] and mark
the 04 holes.
07
2A-3
Drill 4 pilot holes using a 7/32 in.(5.5 mm) diameter drill bit. Make sure the depth is not less than 2 9/16 in.(65mm).
2A-4
2 9/16 in.(65mm)
ø7/32 in.(5.5 mm)
Install the wall plate using lag screws [A1] and washer [A2]. Tighten the lag
screws [A1] only until the washers [A2] are pulled firmly against the wall
plate. 01
A1 A2
You may need assistance with this step.
Step 2B Solid Concrete or Concrete Block Option
1/2 in.(13mm) Socket Wrench (Not included)
WARNING:
Avoid potential personal injury or property damage! DO NOT over-tighten the
lag screws [A1]. Tighten the lag screws [A1] only until the washers [A2] are
pulled firmly against the wall plate.
Ensure the wall plate [01] is securely fastened to the wall before continuing
to the next step.
Any material covering the wall must not exceed 5/8 in. (16 mm) Mount the wall
plate directly onto the concrete surface Minimum solid concrete thickness: 203
mm (8 in.) Minimum concrete block size: 203 x 203 x 406 mm (8 x 8 x 16 in.)
Never drill into the mortar between blocks
Wall Anchor
A3
08
2B-1 2B-2 2B-3 2B-4
A1 A2
Position the wall plate template [04] at your desired height, level the wall
plate template and mark the pilot hole locations. 04
Drill 6 pilot holes using a 3/8 in.(10mm)diameter drill bit. Make sure the
depth is not less than 2 3/4 in.(70mm). Never drill into the mortar between
blocks.
2 3/4 in.(70mm)
ø3/8 in.(10mm)
Use the hammer to knock anchors [A3] into the wall. Be sure the anchors [A3]
are seated flush with the concrete surface.
Install wall plate using lag screws [A1], washers [A2] and anchors [A3].
Tighten the lag
screws [A1] only until the washers [A2] are pulled firmly against the wall
plate. DO NOT over-tighten the lag screws [A1]. 01
You may need assistance with this step.
09
1/2 in.(13mm) Socket Wrench (Not included)
Step 3 Secure the Arm Assembly [02] to Wall Plate [01] 1. Hang the arm assembly [02] to wall plate [01]. 2. Shift the arm assembly [02] along the wall plate [01] to your desired position. 3. Secure the arm assembly [02] to wall plate [01] using bolts [F1].
02
01
F1
Note: The bolts [F1] need
Allen Key
to be tightened hard.
Step 4 Secure Front Support to Arm Assembly
09 02
1.Make sure the big button in Front Support [09] hangs on the hook of the arm
assembly.
2.Secure the front support [09] to arm assembly [02] using bolts [F2].
F2
Allen Key
10
Step 5 Hang the TV onto the Front Support 5-1 Remove the preassembled bolt [S]
and save to use in 5-2
S
Screwdriver (Not lncluded)
5-2 Hang the TV with brackets [03] onto the front support [09]
S
Press the safety locks down, then fasten the removed bolts [S]
Screwdriver (Not lncluded)
HEAVY! You may need assistance with this step.
11
Step 6 Adjustments
Level
CAUTION!
DO NOT over-loosen these four nuts when adjusting the level angle to prevent
the TV from falling off.
1.Loosen the bolt [F2] . 2.Level your TV. 3.Tighten the bolt [F2] to secure the TV in place.
F2
Allen Key
F2
1. Loosen the preassembled knob [T].
Tilt
2. Adjust TV to your desired tilt angle.
3. Tighten the preassembled knob [T] to secure the TV in place.
Loosen
T
Tighten
T
12
Horizontal Shift
Note: Please take off the TV before shifting the arm assmebly along the wall plate
Loosen bolts [S] S
Take off TV
To better position your mount and TV on your wall, the mount can be horizontal
shifted left to right by following these steps.
1. Loosen the bolts [F1]. 2. Shift the arm assembly [02] to your desired
position. 3. Tighten the bolts [F1] hard. 4. Repeat the procedures in Step 5
to rehang and secure the TV onto the front
support[09].
02
F1
Note: The bolts [F1] need
to be tightened hard.
HEAVY! You may need assistance with this step.
13
Allen Key
Thank you again
for choosing this Perlesmith product!
All of us at Perlesmith do appreciate your product purchase. We hope that you
are as happy with your product as we are designing and manufacturing it for
you. We strive to provide you with the best quality products and services in
the industry. Please share your experience of our product with others at
www.perlesmith.com if you are satisfied. If you have any questions please
don’t hesitate to contact us at Technical Support:
1-800-556-6806 Mon-Fri 10am – 5pm (PST)
(USA) (CAN) Other Info: supportus@perlesmith.com (US/CA/DE/UK/FR/IT/ES/AU)
Please check www.perlesmith.com for more products and company information.
Perlesmith offers products in these categories
TV Stands
Anti-tip Straps
AV Shelves
Speaker Stands
TV Carts
Full Motion Mounts
Tilt Mounts
Corner Mounts
Please remember us when you need one.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>